Analyses and Optimization of Physical and Mechanical Properties of Direct Recycled Aluminium Alloy (AA6061) Wastes by ANOVA Approach
The present study is aimed at investigating microhardness and density of aluminium alloy chips when subjected to various settings of preheating temperature and preheating time. Three values of preheating temperature were taken as 450 °C, 500 °C, and 550 °C. On the other hand, three values of preheating time were chosen (1, 2, 3) hours. The influences of the process parameters (preheating temperature and time) were analyzed using Design of Experiments (DOE) approach whereby full factorial design with center point analysis was adopted. The total runs were 11 and they comprise of two factors of full factorial design with 3 center points. The responses were microhardness and density. The results showed that the density and microhardness increased with decreasing the preheating temperature. The results also found that the preheating temperature is more important to be controlled rather than the preheating time in microhardness analysis while both the preheating temperature and preheating time are important in density analysis. It can be concluded that setting temperature at 450 °C for 1 hour resulted in the optimum responses.
 S Shamsudin, Z. W. Zhong, S. N Ab Rahim & M. A. Lajis (2016) The influence of temperature and preheating time in extrudate quality of solid-state recycled aluminum. Int J Adv Manuf Technol DOI 10.1007/s00170-016-9521-4.
 G. Gaustad, E. Olivetti, and R. Kirchain, “Economic and environmental evaluation of various aluminum scrap upgrading options using chance constrained optimization modeling,” in Global symposium on recycling, waste treatment, and clean technology (REWAS), 2008.
 Ahmed Sahib Mahdi, Mohd Sukri Mustapa, Mohd Amri lajis and Mohd warikh abd Rashid (2016) Compression Strength and Microhardness of Recycling Milled Aluminium (AA6061) for Various Binder Vol. 3, Issue 2, pp: (98-104), Month: October 2015 - March 2016
 J. Gronostajski, H. Marciniak, and a. Matuszak, “New methods of aluminium and aluminium-alloy chips recycling,” J. Mater. Process. Technol., vol. 106, pp. 34–39, 2000.
 Kadir, M. I. A., Mustapa, M. S., Ibrahim, M. R., Samsi, M. A., Mahdi, A. S. (2017) Microstructures and characteristics of solid state recycling aluminium chips AA6061/Al-SiC composites fabricated by cold compaction method.
 Samsi, M. A., Mustapa, M. S., Badarulzaman, N. A., Kadir, M. I. A., Mahdi, A. S. 2017 The effect of quenching on physical characteristics of recycled AA6061 aluminum chips.
 Mahdi, A. S., Mustapa, M. S., Lajis, M. A., Rashid, M. W. A.2016, Effect of compaction pressure on mechanical properties of aluminium particle sizes AA6061al alloy through powder metallurgical process.
 Chiba R, Yoshimura M (2015) Solid-state recycling of aluminium alloy swarf into c-channel by hot extrusion. JManuf Process 17(0): 1–8. doi:10.1016/j.jmapro.2014.10.002.
 S Shamsudin, M. A. Lajis and Z. W. Zhong, Solid-state recycling of light metals: A review, 2016.
 S. N. Ab Rahim, M. A. Lajis, S. Ariffin. A Review on Recycling Aluminum Chips by Hot Extrusion Process, 2015.
 Kondoh K, Luangvaranunt T, Aizawa T (2002) Solid-state recycle processing for magnesium alloy waste via direct hot forging. Mater Trans 43(3):322–325.
 Mohammed H. Rady, Mohd Sukri Mustapa, S Shamsudin and M. A. Lajis Optimization of the Temperature Related Parameters in Solid-State Recycled Aluminium Alloy (AA6061) Via Design of Experiments (DOE) Method, 2017.