Heat and Mass Transfer Modelling of Industrial Sludge Drying at Different Pressures and Temperatures
A two-dimensional finite volume axisymmetric model is developed to predict the simultaneous heat and mass transfers during the drying of industrial sludge. The simulations were run using COMSOL-Multiphysics 3.5a. The input parameters of the numerical model were acquired from a preliminary experimental work. Results permit to establish correlations describing the evolution of the various parameters as a function of the drying temperature and the sludge water content. The selection and coupling of the equation are validated based on the drying kinetics acquired experimentally at a temperature range of 45-65 °C and absolute pressure range of 200-1000 mbar. The model, incorporating the heat and mass transfer mechanisms at different operating conditions, shows simulated values of temperature and water content. Simulated results are found concordant with the experimental values, only at the first and last drying stages where sludge shrinkage is insignificant. Simulated and experimental results show that sludge drying is favored at high temperatures and low pressure. As experimentally observed, the drying time is reduced by 68% for drying at 65 °C compared to 45 °C under 1 atm. At 65 °C, a 200-mbar absolute pressure vacuum leads to an additional reduction in drying time estimated by 61%. However, the drying rate is underestimated in the intermediate stage. This rate underestimation could be improved in the model by considering the shrinkage phenomena that occurs during sludge drying.
 BG Aval / DMDR - AREVA, Rapport d’avancement sur la gestion des dechets radioactifs MAVL d’AREVA, (2015).
 S. Louarn, J. Ploteau, P. Glouannec, H. Noel, Experimental and numerical study of flat plate sludge drying at low temperature by convection and direct conduction, Drying Technology. 32 (2014) 1664–1674. https://doi.org/10.1080/07373937.2014.916299.
 N.B. Hassine, X. Chesneau, A.H. Laatar, Numerical modeling of heat and mass transfers under solar drying of sewage sludge, Heat Transfer Research. 49 (2012) 327–348. https://doi.org/10.1615/HeatTransRes.2018017977.
 D. Wu, X. Peng, A. Su, A. Mujumdar, C. Hsu, D. Lee, Heat and mass transfer in unsaturated porous cake with heated walls, Drying Technology. 26 (2008) 1079–1085. https://doi.org/10.1080/07373930802179491.
 R. Thuwapanichayanan, S. Prachayawarakorn, S. Soponronnarit, Modeling of diffusion with shrinkage and quality investigation of banana foam mat drying, Drying Technology. 26 (2008) 1326–1333. https://doi.org/10.1080/07373930802330979.
 M. Kohout, A.P. Collier, F. Štěpánek, Mathematical modelling of solvent drying from a static particle bed, Chemical Engineering Science. 61 (2006) 3674–3685. https://doi.org/10.1016/j.ces.2005.12.036.
 M. Murru, G. Giorgio, S. Montomoli, F. Ricard, F. Stepanek, Model-based scale-up of vacuum contact drying of pharmaceutical compounds, Chemical Engineering Science. 66 (2011) 5045–5054. https://doi.org/10.1016/j.ces.2011.06.059.
 C. L. Yaws, The Yaws Handbook of Vapor Pressure : Antoine Coefficients, Gulf Prof. Pub., 336p, Elsevier, 2015. https://doi.org/10.1016/C2014-0-03590-3.
 B.K. Koua, P.M.E. Koffi, P. Gbaha, Evolution of shrinkage, real density, porosity, heat and mass transfer coefficients during indirect solar drying of cocoa beans, Journal of the Saudi Society of Agricultural Sciences. 18 (2019) 72–82. https://doi.org/10.1016/j.jssas.2017.01.002.