Open Science Research Excellence

Open Science Index

Commenced in January 2007 Frequency: Monthly Edition: International Publications Count: 30132


Select areas to restrict search in scientific publication database:
10010373
Studies on the Characterization and Machinability of Duplex Stainless Steel 2205 during Dry Turning
Abstract:
The present investigation is a study of the effect of advanced Physical Vapor Deposition (PVD) coatings on cutting temperature residual stresses and surface roughness during Duplex Stainless Steel (DSS) 2205 turning. Austenite stabilizers like nickel, manganese, and molybdenum reduced the cost of DSS. Surface Integrity (SI) plays an important role in determining corrosion resistance and fatigue life. Resistance to various types of corrosion makes DSS suitable for applications with critical environments like Heat exchangers, Desalination plants, Seawater pipes and Marine components. However, lower thermal conductivity, poor chip control and non-uniform tool wear make DSS very difficult to machine. Cemented carbide tools (M grade) were used to turn DSS in a dry environment. AlTiN and AlTiCrN coatings were deposited using advanced PVD High Pulse Impulse Magnetron Sputtering (HiPIMS) technique. Experiments were conducted with cutting speed of 100 m/min, 140 m/min and 180 m/min. A constant feed and depth of cut of 0.18 mm/rev and 0.8 mm were used, respectively. AlTiCrN coated tools followed by AlTiN coated tools outperformed uncoated tools due to properties like lower thermal conductivity, higher adhesion strength and hardness. Residual stresses were found to be compressive for all the tools used for dry turning, increasing the fatigue life of the machined component. Higher cutting temperatures were observed for coated tools due to its lower thermal conductivity, which results in very less tool wear than uncoated tools. Surface roughness with uncoated tools was found to be three times higher than coated tools due to lower coefficient of friction of coating used.
Digital Object Identifier (DOI):

References:

[1] Robert N Gunn, Duplex Stainless Steels: microstructure, Properties and Applications. Woodhead Publishing: United Kingdom, 1997, pp. 4-54.
[2] J. Olsson, M. Snis, “Duplex— a new generation of stainless steels for desalination plants”, Desalination, vol. 205(1–3), 2007, pp. 104–113.
[3] J.O. Nilsson, “Super duplex stainless steels”, Materials Science and Technology, vol. 8, 1992, pp. 685-700.
[4] Atul Kulkarni, Vikas Sargade, “Charaterization and performance of AlTiN, AlTiCrN, TiN/TiAlN PVD coated carbide tolls while turning SS304”, Materials and Manufacturing Processes, vol. 30, 2015, pp. 748-755.
[5] I. Ciftci, “Machining of austenitic stainless steels using CVD multi-layer coated cemented carbide tools”, Tribology International, vol. 39(6), 2006, pp. 565–569.
[6] B. Voronenko, “Austenitic-ferritic stainless steels: a state of the art review”, Metal Science and Heat Treatment, vol. 39 (10), 1997, pp. 428–439.
[7] Sonawane, G. D.; Sargade, V. G.; Machinability Studies of Duplex Stainless Steel 2205 using Coated Tools in Proc. 10th International Conference on Precision, Meso, Micro and Nano Engineering (COPEN 10), Madras, 2017, pp. 460-463.
[8] Sharma A. K., Tiwari A. K., Dixit A. R., “Effect of minimum quality Lubrication (MQL) in machining process using conventional and nano-fluid based cutting fluids: a review”, Clean Production, vol. 67, 2016, pp. 197-207.
[9] Bunshah, R. F. Handbook of Hard Coatings; William Andrew Publishing: New York, 2002, ch. 5.
[10] G. Krolczyk, P. Nieslony, and S. Legutko, “Determination of tool life and research wear during duplex stainless steel turning”, Archives of civil and mechanical engineering, vol. 15, 2015, pp. 347-354.
[11] Sharma A. K., Tiwari A. K., Dixit A. R., “Effect of minimum quality Lubrication (MQL) in machining process using conventional and nano-fluid based cutting fluids: a review”, Clean Production, vol. 67, 2016, pp. 197-207.
[12] Q. Ran, J. Li, Y. Xu, X. Xiao, H. Yu, L. Jiang, “Novel Cu-bearing economical 21Cr duplex stainless steels”, Materials and Design, 46 (2013), 758–765. Q. Ran, J. Li, Y. Xu, X. Xiao, H. Yu, L. Jiang, “Novel Cu-bearing economical 21Cr duplex stainless steels”, Materials and Design, vol. 46, 2013, pp. 758–765.
[13] Królczyk, G.; Gajek, M.; Legutko S., “Effect of the Cutting Parameters Impact on Tool Life in Duplex Stainless Steel Turning Process”, Tehnicki Vjesnik (Technical News), vol. 20(4), 2013, pp. 587-592.
[14] D. Philip Selvaraj, Palanisamy Chandramohan, “Influence of Cutting Speed, Feed Rate and Bulk Texture on the Surface Finish of Nitrogen Alloyed Duplex Stainless Steels during Dry Turning”, Scientific research Engineering, vol. 2, 2010, pp. 453-460.
[15] Królczyk, G.; Gajek, M.; Legutko S., “Effect of the Cutting Parameters Impact on Tool Life in Duplex Stainless Steel Turning Process”, Tehnicki Vjesnik (Technical News), vol. 20(4), 2013, pp. 587-592.
[16] M. Alauddin, M. A. El Baradie and M. S. J. Hashmi “Prediction of tool life in end milling by response surface methodology”, Journal of Materials Processing and Technology, vol. 71, 1997, pp. 456-465.
[17] G. Krolczyk, P. Nieslony, and S. Legutko, “Microhardness and Surface Integrity in Turning Process of Duplex Stainless Steel (DSS) for Different Cutting Conditions”, Journal of Materials Engineering and Performance, vol. 23, 2014, pp. 859–866.
[18] N. Solomon and I. Solomon, “Deformation induced Martensite in AISI 316 Stainless Steel”, Metallurgy, vol. 46(2), 2010, pp. 131-136.
[19] T Braham-Bouchnak, G. Germain, “High pressure Water Jet Assisted Machining of Duplex SS: Machinability and Tool Life”, International Journal of Material Forming, vol. 3 (1), 2010, pp. 507-510.
[20] Chen et. al., Investigation on the thermostability of residual stress and microstructure in shot peened SAF 2507 duplex stainless steel, Vacuum, vol. 218, 2018, pp. 145-153.
[21] Garcia et. al., Effect of cutting parameters in the surface residual stresses generated by turning in AISI 4340 steel, International Journal of Machine Tools & Manufacture, vol. 61, 2012, pp. 48–57.
Vol:13 No:11 2019Vol:13 No:10 2019Vol:13 No:09 2019Vol:13 No:08 2019Vol:13 No:07 2019Vol:13 No:06 2019Vol:13 No:05 2019Vol:13 No:04 2019Vol:13 No:03 2019Vol:13 No:02 2019Vol:13 No:01 2019
Vol:12 No:12 2018Vol:12 No:11 2018Vol:12 No:10 2018Vol:12 No:09 2018Vol:12 No:08 2018Vol:12 No:07 2018Vol:12 No:06 2018Vol:12 No:05 2018Vol:12 No:04 2018Vol:12 No:03 2018Vol:12 No:02 2018Vol:12 No:01 2018
Vol:11 No:12 2017Vol:11 No:11 2017Vol:11 No:10 2017Vol:11 No:09 2017Vol:11 No:08 2017Vol:11 No:07 2017Vol:11 No:06 2017Vol:11 No:05 2017Vol:11 No:04 2017Vol:11 No:03 2017Vol:11 No:02 2017Vol:11 No:01 2017
Vol:10 No:12 2016Vol:10 No:11 2016Vol:10 No:10 2016Vol:10 No:09 2016Vol:10 No:08 2016Vol:10 No:07 2016Vol:10 No:06 2016Vol:10 No:05 2016Vol:10 No:04 2016Vol:10 No:03 2016Vol:10 No:02 2016Vol:10 No:01 2016
Vol:9 No:12 2015Vol:9 No:11 2015Vol:9 No:10 2015Vol:9 No:09 2015Vol:9 No:08 2015Vol:9 No:07 2015Vol:9 No:06 2015Vol:9 No:05 2015Vol:9 No:04 2015Vol:9 No:03 2015Vol:9 No:02 2015Vol:9 No:01 2015
Vol:8 No:12 2014Vol:8 No:11 2014Vol:8 No:10 2014Vol:8 No:09 2014Vol:8 No:08 2014Vol:8 No:07 2014Vol:8 No:06 2014Vol:8 No:05 2014Vol:8 No:04 2014Vol:8 No:03 2014Vol:8 No:02 2014Vol:8 No:01 2014
Vol:7 No:12 2013Vol:7 No:11 2013Vol:7 No:10 2013Vol:7 No:09 2013Vol:7 No:08 2013Vol:7 No:07 2013Vol:7 No:06 2013Vol:7 No:05 2013Vol:7 No:04 2013Vol:7 No:03 2013Vol:7 No:02 2013Vol:7 No:01 2013
Vol:6 No:12 2012Vol:6 No:11 2012Vol:6 No:10 2012Vol:6 No:09 2012Vol:6 No:08 2012Vol:6 No:07 2012Vol:6 No:06 2012Vol:6 No:05 2012Vol:6 No:04 2012Vol:6 No:03 2012Vol:6 No:02 2012Vol:6 No:01 2012
Vol:5 No:12 2011Vol:5 No:11 2011Vol:5 No:10 2011Vol:5 No:09 2011Vol:5 No:08 2011Vol:5 No:07 2011Vol:5 No:06 2011Vol:5 No:05 2011Vol:5 No:04 2011Vol:5 No:03 2011Vol:5 No:02 2011Vol:5 No:01 2011
Vol:4 No:12 2010Vol:4 No:11 2010Vol:4 No:10 2010Vol:4 No:09 2010Vol:4 No:08 2010Vol:4 No:07 2010Vol:4 No:06 2010Vol:4 No:05 2010Vol:4 No:04 2010Vol:4 No:03 2010Vol:4 No:02 2010Vol:4 No:01 2010
Vol:3 No:12 2009Vol:3 No:11 2009Vol:3 No:10 2009Vol:3 No:09 2009Vol:3 No:08 2009Vol:3 No:07 2009Vol:3 No:06 2009Vol:3 No:05 2009Vol:3 No:04 2009Vol:3 No:03 2009Vol:3 No:02 2009Vol:3 No:01 2009
Vol:2 No:12 2008Vol:2 No:11 2008Vol:2 No:10 2008Vol:2 No:09 2008Vol:2 No:08 2008Vol:2 No:07 2008Vol:2 No:06 2008Vol:2 No:05 2008Vol:2 No:04 2008Vol:2 No:03 2008Vol:2 No:02 2008Vol:2 No:01 2008
Vol:1 No:12 2007Vol:1 No:11 2007Vol:1 No:10 2007Vol:1 No:09 2007Vol:1 No:08 2007Vol:1 No:07 2007Vol:1 No:06 2007Vol:1 No:05 2007Vol:1 No:04 2007Vol:1 No:03 2007Vol:1 No:02 2007Vol:1 No:01 2007