205
6249
Effect of Valve Pressure Drop in Exergy Analysis of C2+ Recovery Plants Refrigeration Cycles
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Digital Article Identifier (DOI):
204
11531
Using Support Vector Machine for Prediction Dynamic Voltage Collapse in an Actual Power System
Abstract: This paper presents dynamic voltage collapse prediction on an actual power system using support vector machines.
Dynamic voltage collapse prediction is first determined based on the PTSI calculated from information in dynamic simulation output. Simulations were carried out on a practical 87 bus test system by considering load increase as the contingency. The data collected from the time domain simulation is then used as input to the SVM in which support vector regression is used as a predictor to determine the
dynamic voltage collapse indices of the power system. To reduce training time and improve accuracy of the SVM, the Kernel function type and Kernel parameter are considered. To verify the
effectiveness of the proposed SVM method, its performance is compared with the multi layer perceptron neural network (MLPNN). Studies show that the SVM gives faster and more accurate results for dynamic voltage collapse prediction compared with the MLPNN.
Digital Article Identifier (DOI):
203
570
Library Aware Power Conscious Realization of Complementary Boolean Functions
Abstract: In this paper, we consider the problem of logic simplification for a special class of logic functions, namely complementary Boolean functions (CBF), targeting low power implementation using static CMOS logic style. The functions are uniquely characterized by the presence of terms, where for a canonical binary 2-tuple, D(mj) ∪ D(mk) = { } and therefore, we have | D(mj) ∪ D(mk) | = 0 [19]. Similarly, D(Mj) ∪ D(Mk) = { } and hence | D(Mj) ∪ D(Mk) | = 0. Here, 'mk' and 'Mk' represent a minterm and maxterm respectively. We compare the circuits minimized with our proposed method with those corresponding to factored Reed-Muller (f-RM) form, factored Pseudo Kronecker Reed-Muller (f-PKRM) form, and factored Generalized Reed-Muller (f-GRM) form. We have opted for algebraic factorization of the Reed-Muller (RM) form and its different variants, using the factorization rules of [1], as it is simple and requires much less CPU execution time compared to Boolean factorization operations. This technique has enabled us to greatly reduce the literal count as well as the gate count needed for such RM realizations, which are generally prone to consuming more cells and subsequently more power consumption. However, this leads to a drawback in terms of the design-for-test attribute associated with the various RM forms. Though we still preserve the definition of those forms viz. realizing such functionality with only select types of logic gates (AND gate and XOR gate), the structural integrity of the logic levels is not preserved. This would consequently alter the testability properties of such circuits i.e. it may increase/decrease/maintain the same number of test input vectors needed for their exhaustive testability, subsequently affecting their generalized test vector computation. We do not consider the issue of design-for-testability here, but, instead focus on the power consumption of the final logic implementation, after realization with a conventional CMOS process technology (0.35 micron TSMC process). The quality of the resulting circuits evaluated on the basis of an established cost metric viz., power consumption, demonstrate average savings by 26.79% for the samples considered in this work, besides reduction in number of gates and input literals by 39.66% and 12.98% respectively, in comparison with other factored RM forms.
Digital Article Identifier (DOI):
202
1691
Visual Tag-based Location-Aware System for Household Robots
Abstract: This paper proposes a location-aware system for
household robots which allows users to paste predefined paper tags at
different locations according to users- comprehension of the house. In this system a household robot may be aware of its location and the
attributes thereof by visually recognizing the tags when the robot is moving. This paper also presents a novel user interface to define a
moving path of the robot, which allows users to draw the path in the air
with a finger so as to generate commands for following motions.
Digital Article Identifier (DOI):
201
11630
A Dynamic Decision Model for Vertical Handoffs across Heterogeneous Wireless Networks
Abstract: The convergence of heterogeneous wireless access technologies characterizes the 4G wireless networks. In such converged systems, the seamless and efficient handoff between
different access technologies (vertical handoff) is essential and remains a challenging problem. The heterogeneous co-existence of access technologies with largely different characteristics creates a decision problem of determining the “best" available network at
“best" time to reduce the unnecessary handoffs. This paper proposes a dynamic decision model to decide the “best" network at “best"
time moment to handoffs. The proposed dynamic decision model make the right vertical handoff decisions by determining the “best"
network at “best" time among available networks based on, dynamic
factors such as “Received Signal Strength(RSS)" of network and
“velocity" of mobile station simultaneously with static factors like Usage Expense, Link capacity(offered bandwidth) and power
consumption. This model not only meets the individual user needs but also improve the whole system performance by reducing the unnecessary handoffs.
Digital Article Identifier (DOI):
200
1812
Control of Pendulum on a Cart with State Dependent Riccati Equations
Abstract: State Dependent Riccati Equation (SDRE) approach is
a modification of the well studied LQR method. It has the capability of being applied to control nonlinear systems. In this paper the technique
has been applied to control the single inverted pendulum (SIP) which represents a rich class of nonlinear underactuated systems. SIP
modeling is based on Euler-Lagrange equations. A procedure is developed
for judicious selection of weighting parameters and constraint handling. The controller designed by SDRE technique here gives better results than existing controllers designed by energy based techniques.
Digital Article Identifier (DOI):
199
3340
Transmission Planning – a Probabilistic Load Flow Perspective
Abstract: Perhaps no single issue has been cited as either the root
cause and / or the greatest challenge to the restructured power system then the lack of adequate reliable transmission. Probabilistic transmission planning has become increasingly necessary and important in recent
years. The transmission planning analysis carried out by the authors,
spans a 10-year horizon, taking into consideration a value of 2 % load
increase / year at each consumer. Taking into consideration this increased
load, a probabilistic power flow was carried out, all the system components
being regarded from probabilistic point of view. Several contingencies
have been generated, for assessing the security of the power system. The results have been analyzed and several important conclusions were pointed. The objective is to achieve a network that works without limit violations for all (or most of) scenario realizations. The case study is represented by the IEEE 14 buses test power system.
Digital Article Identifier (DOI):
198
2157
Machine Vision System for Automatic Weeding Strategy in Oil Palm Plantation using Image Filtering Technique
Abstract: Machine vision is an application of computer vision to automate conventional work in industry, manufacturing or any other
field. Nowadays, people in agriculture industry have embarked into research on implementation of engineering technology in their farming activities. One of the precision farming activities that involve machine vision system is automatic weeding strategy. Automatic weeding strategy in oil palm plantation could minimize
the volume of herbicides that is sprayed to the fields. This paper discusses an automatic weeding strategy in oil palm plantation using machine vision system for the detection and differential spraying of weeds. The implementation of vision system involved the used of
image processing technique to analyze weed images in order to recognized and distinguished its types. Image filtering technique has
been used to process the images as well as a feature extraction method to classify the type of weed images. As a result, the image processing technique contributes a promising result of classification to be implemented in machine vision system for automated weeding strategy.
Digital Article Identifier (DOI):
197
8921
Performance Analysis of Quantum Cascaded Lasers
Abstract: Improving the performance of the QCL through block diagram as well as mathematical models is the main scope of this paper. In order to enhance the performance of the underlined device, the mathematical model parameters are used in a reliable manner in such a way that the optimum behavior was achieved. These parameters play the central role in specifying the optical characteristics of the considered laser source. Moreover, it is important to have a large amount of radiated power, where increasing the amount of radiated power represents the main hopping process that can be predicted from the behavior of quantum laser devices. It was found that there is a good agreement between the calculated values from our mathematical model and those obtained with VisSim and experimental results. These demonstrate the strength of mplementation of both mathematical and block diagram models.
Digital Article Identifier (DOI):
196
12104
A Dynamic Model for a Drill in the Drilling Process
Abstract: The dynamic model of a drill in drilling process was
proposed and investigated in this study. To assure a good drilling quality, the vibration variation on the drill tips during high speed
drilling is needed to be investigated. A pre-twisted beam is used to
simulate the drill. The moving Winkler-Type elastic foundation is used to characterize the tip boundary variation in drilling. Due to the
variation of the drill depth, a time dependent dynamic model for the drill is proposed. Results simulated from this proposed model indicate that an abrupt natural frequencies drop are experienced as the drill tip
tough the workpiece, and a severe vibration is induced. The effects of parameters, e.g. drilling speed, depth, drill size and thrust force on the
drill tip responses studied.
Digital Article Identifier (DOI):
195
12657
A Novel Methodology for Synthesis of Fault Trees from MATLAB-Simulink Model
Abstract: Fault tree analysis is a well-known method for
reliability and safety assessment of engineering systems. In the last 3
decades, a number of methods have been introduced, in the literature,
for automatic construction of fault trees. The main difference between these methods is the starting model from which the tree is constructed. This paper presents a new methodology for the construction of static and dynamic fault trees from a system Simulink
model. The method is introduced and explained in detail, and its correctness and completeness is experimentally validated by using an example, taken from literature. Advantages of the method are also mentioned.
Digital Article Identifier (DOI):
194
8705
A New Framework for Evaluation and Prioritization of Suppliers using a Hierarchical Fuzzy TOPSIS
Abstract: This paper suggests an algorithm for the evaluation
and selection of suppliers. At the beginning, all the needed materials and services used by the organization were identified and categorized
with regard to their nature by ABC method. Afterwards, in order to reduce risk factors and maximize the organization's profit, purchase strategies were determined. Then, appropriate criteria were identified for primary evaluation of suppliers applying to the organization. The output of this stage was a list of suppliers qualified by the organization to participate in its tenders. Subsequently, considering a material in particular, appropriate criteria on the ordering of the
mentioned material were determined, taking into account the particular materials' specifications as well as the organization's needs. Finally, for the purpose of validation and verification of the
proposed model, it was applied to Mobarakeh Steel Company (MSC), the qualified suppliers of this Company are ranked by the means of a Hierarchical Fuzzy TOPSIS method. The obtained results
show that the proposed algorithm is quite effective, efficient and easy to apply.
Digital Article Identifier (DOI):
193
249
A Low Voltage High Performance Self Cascode Current Mirror
Abstract: A current mirror (CM) based on self cascode MOSFETs low voltage analog and mixed mode structures has been proposed. The proposed CM has high output impedance and can operate at 0.5 V. P-Spice simulations confirm the high performance of this CM with a bandwidth of 6.0 GHz at input current of 100 μA.
Digital Article Identifier (DOI):
192
4482
A Hybrid Distributed Vision System for Robot Localization
Abstract: Localization is one of the critical issues in the field of
robot navigation. With an accurate estimate of the robot pose, robots will be capable of navigating in the environment autonomously and efficiently. In this paper, a hybrid Distributed Vision System (DVS)
for robot localization is presented. The presented approach integrates
odometry data from robot and images captured from overhead cameras
installed in the environment to help reduce possibilities of fail
localization due to effects of illumination, encoder accumulated errors,
and low quality range data. An odometry-based motion model is applied to predict robot poses, and robot images captured by overhead
cameras are then used to update pose estimates with HSV histogram-based measurement model. Experiment results show the
presented approach could localize robots in a global world coordinate system with localization errors within 100mm.
Digital Article Identifier (DOI):
191
8489
Digital Redesign of Interval Systems via Particle Swarm Optimization
Abstract: In this paper, a PSO-based approach is proposed to
derive a digital controller for redesigned digital systems having an interval plant based on resemblance of the extremal gain/phase
margins. By combining the interval plant and a controller as an interval system, extremal GM/PM associated with the loop transfer function
can be obtained. The design problem is then formulated as an optimization problem of an aggregated error function revealing the deviation on the extremal GM/PM between the redesigned digital
system and its continuous counterpart, and subsequently optimized by
a proposed PSO to obtain an optimal set of parameters for the digital controller. Computer simulations have shown that frequency
responses of the redesigned digital system having an interval plant bare a better resemblance to its continuous-time counter part by the incorporation of a PSO-derived digital controller in comparison to those obtained using existing open-loop discretization methods.
Digital Article Identifier (DOI):
190
14501
A 7DOF Manipulator Control in an Unknown Environment based on an Exact Algorithm
Abstract: An exact algorithm for a n-link manipulator movement amidst arbitrary unknown static obstacles is presented.
The algorithm guarantees the reaching of a target configuration of the manipulator in a finite number of steps. The algorithm is
reduced to a finite number of calls of a subroutine for planning a trajectory in the presence of known forbidden states. The polynomial approximation algorithm which is used as the subroutine is presented. The results of the exact algorithm
implementation for the control of a seven link (7 degrees of
freedom, 7DOF) manipulator are given.
Digital Article Identifier (DOI):
189
15333
Digital Automatic Gain Control Integrated on WLAN Platform
Abstract: In this work we present a solution for DAGC (Digital
Automatic Gain Control) in WLAN receivers compatible to IEEE 802.11a/g standard. Those standards define communication in 5/2.4
GHz band using Orthogonal Frequency Division Multiplexing OFDM modulation scheme. WLAN Transceiver that we have used
enables gain control over Low Noise Amplifier (LNA) and a
Variable Gain Amplifier (VGA). The control over those signals is
performed in our digital baseband processor using dedicated hardware block DAGC. DAGC in this process is used to automatically control the VGA and LNA in order to achieve better
signal-to-noise ratio, decrease FER (Frame Error Rate) and hold the
average power of the baseband signal close to the desired set point.
DAGC function in baseband processor is done in few steps: measuring power levels of baseband samples of an RF signal,accumulating the differences between the measured power level and
actual gain setting, adjusting a gain factor of the accumulation, and
applying the adjusted gain factor the baseband values. Based on the measurement results of RSSI signal dependence to input power we have concluded that this digital AGC can be implemented applying
the simple linearization of the RSSI. This solution is very simple but also effective and reduces complexity and power consumption of the
DAGC. This DAGC is implemented and tested both in FPGA and in ASIC as a part of our WLAN baseband processor. Finally, we have integrated this circuit in a compact WLAN PCMCIA board based on MAC and baseband ASIC chips designed from us.
Digital Article Identifier (DOI):
188
14019
Advanced Stochastic Models for Partially Developed Speckle
Abstract: Speckled images arise when coherent microwave,
optical, and acoustic imaging techniques are used to image an object, surface or scene. Examples of coherent imaging systems include synthetic aperture radar, laser imaging systems, imaging sonar
systems, and medical ultrasound systems. Speckle noise is a form of object or target induced noise that results when the surface of the object is Rayleigh rough compared to the wavelength of the illuminating radiation. Detection and estimation in images corrupted
by speckle noise is complicated by the nature of the noise and is not
as straightforward as detection and estimation in additive noise. In
this work, we derive stochastic models for speckle noise, with an emphasis on speckle as it arises in medical ultrasound images. The
motivation for this work is the problem of segmentation and tissue classification using ultrasound imaging. Modeling of speckle in this
context involves partially developed speckle model where an underlying Poisson point process modulates a Gram-Charlier series
of Laguerre weighted exponential functions, resulting in a doubly
stochastic filtered Poisson point process. The statistical distribution of partially developed speckle is derived in a closed canonical form.
It is observed that as the mean number of scatterers in a resolution cell is increased, the probability density function approaches an
exponential distribution. This is consistent with fully developed speckle noise as demonstrated by the Central Limit theorem.
Digital Article Identifier (DOI):
187
6899
An Efficient Multi Join Algorithm Utilizing a Lattice of Double Indices
Abstract: In this paper, a novel multi join algorithm to join
multiple relations will be introduced. The novel algorithm is based
on a hashed-based join algorithm of two relations to produce a double index. This is done by scanning the two relations once. But
instead of moving the records into buckets, a double index will be built. This will eliminate the collision that can happen from a complete hash algorithm. The double index will be divided into join
buckets of similar categories from the two relations. The algorithm then joins buckets with similar keys to produce joined buckets. This
will lead at the end to a complete join index of the two relations. without actually joining the actual relations. The time complexity
required to build the join index of two categories is Om log m where m is the size of each category. Totaling time complexity to O n log m
for all buckets. The join index will be used to materialize the joined relation if required. Otherwise, it will be used along with other join
indices of other relations to build a lattice to be used in multi-join operations with minimal I/O requirements. The lattice of the join indices can be fitted into the main memory to reduce time complexity of the multi join algorithm.
Digital Article Identifier (DOI):
186
15143
Design and Performance of Adaptive Polarized MIMO MC-SS-CDMA System for Downlink Mobile Communications
Abstract: In this paper, an adaptive polarized Multiple-Input
Multiple-Output (MIMO) Multicarrier Spread Spectrum Code Division Multiple Access (MC-SS-CDMA) system is designed for downlink mobile communications. The proposed system will be
examined in Frequency Division Duplex (FDD) mode for both macro urban and suburban environments. For the same transmission
bandwidth, a performance comparison between both nonoverlapped and orthogonal Frequency Division Multiplexing (FDM) schemes will be presented. Also, the proposed system will be compared with
both the closed loop vertical MIMO MC-SS-CDMA system and the
synchronous vertical STBC-MIMO MC-SS-CDMA system. As will
be shown, the proposed system introduces a significant performance
gain as well as reducing the spatial dimensions of the MIMO system
and simplifying the receiver implementation. The effect of the
polarization diversity characteristics on the BER performance will be
discussed. Also, the impact of excluding the cross-polarization MCSS-
CDMA blocks in the base station will be investigated. In addition,
the system performance will be evaluated under different Feedback
Information (FBI) rates for slowly-varying channels. Finally, a
performance comparison for vehicular and pedestrian environments
will be presented
Digital Article Identifier (DOI):
185
1995
Plug and Play Interferometer Configuration using Single Modulator Technique
Abstract: We demonstrate single-photon interference over 10 km using a plug and play system for quantum key distribution. The quality of the interferometer is measured by using the interferometer
visibility. The coding of the signal is based on the phase coding and the value of visibility is based on the interference effect, which result a number of count. The setup gives full control of polarization inside
the interferometer. The quality measurement of the interferometer is based on number of count per second and the system produces 94 % visibility in one of the detectors.
Digital Article Identifier (DOI):
184
12636
A Collusion-Resistant Distributed Signature Delegation Based on Anonymous Mobile Agent
Abstract: This paper presents a novel method that allows an
agent host to delegate its signing power to an anonymous mobile
agent in such away that the mobile agent does not reveal any information about its host-s identity and, at the same time, can be authenticated by the service host, hence, ensuring fairness of service
provision. The solution introduces a verification server to verify the
signature generated by the mobile agent in such a way that even if colluding with the service host, both parties will not get more information than what they already have. The solution incorporates
three methods: Agent Signature Key Generation method, Agent
Signature Generation method, Agent Signature Verification method.
The most notable feature of the solution is that, in addition to allowing secure and anonymous signature delegation, it enables
tracking of malicious mobile agents when a service host is attacked. The security properties of the proposed solution are analyzed, and the solution is compared with the most related work.
Digital Article Identifier (DOI):
183
6988
Product-Based Industrial Information Systems (Application to the Steel Industry)
Abstract: This paper shows a simple and effective approach to
the design and implementation of Industrial Information Systems
(IIS) oriented to control the characteristics of each individual product manufactured in a production line and also their manufacturing conditions. The particular products considered in this work are large steel strips that are coiled just after their manufacturing. However, the approach is directly applicable to coiled strips in other industries, like
paper, textile, aluminum, etc. These IIS provide very detailed information of each manufactured product, which complement the general information managed by the ERP system of the production line. In spite of the high importance of this type of IIS to guarantee and improve the quality of the products manufactured in many industries, there are very few works about them in the technical literature. For this reason, this paper represents an important contribution to the development of this type of IIS, providing guidelines for their design, implementation and exploitation.
Digital Article Identifier (DOI):
182
12583
Development of Content Management System with Animated Graph
Abstract: Animated graph gives some good impressions in
presenting information. However, not many people are able to produce it because the process of generating an animated graph requires some technical skills. This work presents Content
Management System with Animated Graph (CMS-AG). It is a webbased system enabling users to produce an effective and interactive
graphical report in a short time period. It allows for three levels of user authentication, provides update profile, account management, template management, graph management, and track changes. The system development applies incremental development approach, object-oriented concepts and Web programming technologies. The design architecture promotes new technology of reporting. It also helps user cut off unnecessary expenses, save time and learn new things on different levels of users. In this paper, the developed system is described.
Digital Article Identifier (DOI):
181
9316
A Similarity Measure for Clustering and its Applications
Abstract: This paper introduces a measure of similarity between
two clusterings of the same dataset produced by two different
algorithms, or even the same algorithm (K-means, for instance, with
different initializations usually produce different results in clustering
the same dataset). We then apply the measure to calculate the
similarity between pairs of clusterings, with special interest directed
at comparing the similarity between various machine clusterings and
human clustering of datasets. The similarity measure thus can be used
to identify the best (in terms of most similar to human) clustering
algorithm for a specific problem at hand. Experimental results
pertaining to the text categorization problem of a Portuguese corpus
(wherein a translation-into-English approach is used) are presented, as well as results on the well-known benchmark IRIS dataset. The
significance and other potential applications of the proposed measure
are discussed.
Digital Article Identifier (DOI):
180
11981
An Overall Approach to the Communication of Organizations in Conventional and Virtual Offices
Abstract: Organizational communication is an administrative
function crucial especially for executives in the implementation of
organizational and administrative functions. Executives spend a
significant part of their time on communicative activities. Doing his or her daily routine, arranging meeting schedules, speaking on the telephone, reading or replying to business correspondence, or
fulfilling the control functions within the organization, an executive typically engages in communication processes.
Efficient communication is the principal device for the adequate implementation of administrative and organizational activities. For
this purpose, management needs to specify the kind of
communication system to be set up and the kind of communication
devices to be used. Communication is vital for any organization.
In conventional offices, communication takes place within the hierarchical pyramid called the organizational structure, and is known as formal or informal communication. Formal communication
is the type that works in specified structures within the organizational rules and towards the organizational goals. Informal communication, on the other hand, is the unofficial type taking place among staff as
face-to-face or telephone interaction.
Communication in virtual as well as conventional offices is
essential for obtaining the right information in administrative
activities and decision-making. Virtual communication technologies
increase the efficiency of communication especially in virtual teams.
Group communication is strengthened through an inter-group central
channel. Further, ease of information transmission makes it possible
to reach the information at the source, allowing efficient and correct decisions. Virtual offices can present as a whole the elements of information which conventional offices produce in different
environments.
At present, virtual work has become a reality with its pros and
cons, and will probably spread very rapidly in coming years, in line
with the growth in information technologies.
Digital Article Identifier (DOI):
179
5570
Comparing Transformational Leadership in Successful and Unsuccessful Companies
Abstract: In this article, while it is attempted to describe the
problem and its importance, transformational leadership is studied by considering leadership theories. Issues such as the definition of
transformational leadership and its aspects are compared on the basis of the ideas of various connoisseurs and then it (transformational leadership) is examined in successful and
unsuccessful companies. According to the methodology, the
method of research, hypotheses, population and statistical sample
are investigated and research findings are analyzed by using descriptive and inferential statistical methods in the framework of
analytical tables. Finally, our conclusion is provided by considering the results of statistical tests. The final result shows that
transformational leadership is significantly higher in successful companies than unsuccessful ones P
Digital Article Identifier (DOI):
178
12815
Service-Oriented Architecture for Object- Centric Information Fusion
Abstract: In many applications there is a broad variety of
information relevant to a focal “object" of interest, and the fusion of such heterogeneous data types is desirable for classification and
categorization. While these various data types can sometimes be treated as orthogonal (such as the hull number, superstructure color,
and speed of an oil tanker), there are instances where the inference and the correlation between quantities can provide improved fusion
capabilities (such as the height, weight, and gender of a person). A
service-oriented architecture has been designed and prototyped to
support the fusion of information for such “object-centric" situations.
It is modular, scalable, and flexible, and designed to support new data sources, fusion algorithms, and computational resources without affecting existing services. The architecture is designed to simplify
the incorporation of legacy systems, support exact and probabilistic entity disambiguation, recognize and utilize multiple types of
uncertainties, and minimize network bandwidth requirements.
Digital Article Identifier (DOI):
177
11757
Use of Semantic Networks as Learning Material and Evaluation of the Approach by Students
Abstract: This article first summarizes reasons why current approaches supporting Open Learning and Distance Education need to be complemented by tools permitting lecturers, researchers and students to cooperatively organize the semantic content of Learning related materials (courses, discussions, etc.) into a fine-grained shared semantic network. This first part of the article also quickly describes the approach adopted to permit such a collaborative work. Then, examples of such semantic networks are presented. Finally, an evaluation of the approach by students is provided and analyzed.
Digital Article Identifier (DOI):
176
6977
On Methodologies for Analysing Sickness Absence Data: An Insight into a New Method
Abstract: Sickness absence represents a major economic and
social issue. Analysis of sick leave data is a recurrent challenge to analysts because of the complexity of the data structure which is
often time dependent, highly skewed and clumped at zero. Ignoring these features to make statistical inference is likely to be inefficient
and misguided. Traditional approaches do not address these problems. In this study, we discuss model methodologies in terms of statistical techniques for addressing the difficulties with sick leave data. We also introduce and demonstrate a new method by performing a longitudinal assessment of long-term absenteeism using
a large registration dataset as a working example available from the Helsinki Health Study for municipal employees from Finland during the period of 1990-1999. We present a comparative study on model
selection and a critical analysis of the temporal trends, the occurrence
and degree of long-term sickness absences among municipal employees. The strengths of this working example include the large
sample size over a long follow-up period providing strong evidence in supporting of the new model. Our main goal is to propose a way to
select an appropriate model and to introduce a new methodology for analysing sickness absence data as well as to demonstrate model
applicability to complicated longitudinal data.
Digital Article Identifier (DOI):
175
8789
Multimedia E-Books for Digital Mechanism and Gear Library
Abstract: This paper presents a digital engineering library – the
Digital Mechanism and Gear Library, DMG-Lib – providing a multimedia collection of e-books, pictures, videos and animations in the domain of mechanisms and machines. The specific characteristic
about DMG-Lib is the enrichment and cross-linking of the different
sources. DMG-Lib e-books not only present pages as pixel images
but also selected figures augmented with interactive animations. The
presentation of animations in e-books increases the clearness of the
information.
To present the multimedia e-books and make them available in the
DMG-Lib internet portal a special e-book reader called StreamBook
was developed for optimal presentation of digitized books and to
enable reading the e-books as well as working efficiently and individually with the enriched information. The objective is to support different user tasks ranging from information retrieval to
development and design of mechanisms.
Digital Article Identifier (DOI):
174
1497
A Hidden Markov Model-Based Isolated and Meaningful Hand Gesture Recognition
Abstract: Gesture recognition is a challenging task for extracting
meaningful gesture from continuous hand motion. In this paper, we propose an automatic system that recognizes isolated gesture,
in addition meaningful gesture from continuous hand motion for Arabic numbers from 0 to 9 in real-time based on Hidden Markov Models (HMM). In order to handle isolated gesture, HMM using
Ergodic, Left-Right (LR) and Left-Right Banded (LRB) topologies is applied over the discrete vector feature that is extracted from stereo
color image sequences. These topologies are considered to different
number of states ranging from 3 to 10. A new system is developed to recognize the meaningful gesture based on zero-codeword detection
with static velocity motion for continuous gesture. Therefore, the
LRB topology in conjunction with Baum-Welch (BW) algorithm for
training and forward algorithm with Viterbi path for testing presents the best performance. Experimental results show that the proposed system can successfully recognize isolated and meaningful gesture and achieve average rate recognition 98.6% and 94.29% respectively.
Digital Article Identifier (DOI):
173
234
A Low-cost Reconfigurable Architecture for AES Algorithm
Abstract: This paper proposes a low-cost reconfigurable
architecture for AES algorithm. The proposed architecture separates
SubBytes and MixColumns into two parallel data path, and supports
different bit-width operation for this two data path. As a result, different number of S-box can be supported in this architecture. The
throughput and power consumption can be adjusted by changing the
number of S-box running in this design. Using the TSMC 0.18μm CMOS standard cell library, a very low-cost implementation of 7K
Gates is obtained under 182MHz frequency. The maximum throughput is 360Mbps while using 4 S-Box simultaneously, and the
minimum throughput is 114Mbps while only using 1 S-Box
Digital Article Identifier (DOI):
172
3922
Application of the Data Distribution Service for Flexible Manufacturing Automation
Abstract: This paper discusses the applicability of the Data
Distribution Service (DDS) for the development of automated and modular manufacturing systems which require a flexible and robust
communication infrastructure. DDS is an emergent standard for datacentric publish/subscribe middleware systems that provides an
infrastructure for platform-independent many-to-many
communication. It particularly addresses the needs of real-time systems that require deterministic data transfer, have low memory
footprints and high robustness requirements. After an overview of the
standard, several aspects of DDS are related to current challenges for the development of modern manufacturing systems with distributed architectures. Finally, an example application is presented based on a modular active fixturing system to illustrate the described aspects.
Digital Article Identifier (DOI):
171
14248
Reliable Face Alignment Using Two-Stage AAM
Authors: Sunho Ki,
Daehwan Kim,
Seongwon Cho,
Sun-Tae Chung,
Jaemin Kim,
Yun-Kwang Hong,
Chang Joon Park,
Dongmin Kwon,
Minhee Kang,
Yusung Kim,
Younghan Yoon
Abstract: AAM (active appearance model) has been successfully
applied to face and facial feature localization. However, its performance is sensitive to initial parameter values. In this paper, we propose a two-stage AAM for robust face alignment, which first fits an
inner face-AAM model to the inner facial feature points of the face and then localizes the whole face and facial features by optimizing the
whole face-AAM model parameters. Experiments show that the proposed face alignment method using two-stage AAM is more reliable to the background and the head pose than the standard
AAM-based face alignment method.
Digital Article Identifier (DOI):
170
12095
Computationally Efficient Adaptive Rate Sampling and Adaptive Resolution Analysis
Abstract: Mostly the real life signals are time varying in nature. For proper characterization of such signals, time-frequency representation is required. The STFT (short-time Fourier transform) is a classical tool used for this purpose. The limitation of the STFT is its fixed time-frequency resolution. Thus, an enhanced version of the STFT, which is based on the cross-level sampling, is devised. It can adapt the sampling frequency and the window function length by following the input signal local variations. Therefore, it provides an adaptive resolution time-frequency representation of the input. The computational complexity of the proposed STFT is deduced and compared to the classical one. The results show a significant gain of the computational efficiency and hence of the processing power. The processing error of the proposed technique is also discussed.
Digital Article Identifier (DOI):
169
12392
Application of a Time-Frequency-Based Blind Source Separation to an Instantaneous Mixture of Secondary Radar Sources
Abstract: In Secondary Surveillance Radar (SSR) systems, it is
more difficult to locate and recognise aircrafts in the neighbourhood of civil airports since aerial traffic becomes greater. Here, we propose to apply a recent Blind Source Separation (BSS) algorithm based
on Time-Frequency Analysis, in order to separate messages sent by different aircrafts and falling in the same radar beam in reception. The above source separation method involves joint-diagonalization
of a set of smoothed version of spatial Wigner-Ville distributions.
The technique makes use of the difference in the t-f signatures of the nonstationary sources to be separated. Consequently, as the SSR sources emit different messages at different frequencies, the above fitted to this new application. We applied the technique in simulation to separate SSR replies. Results are provided at the end
of the paper.
Digital Article Identifier (DOI):
168
10176
Target Detection using Adaptive Progressive Thresholding Based Shifted Phase-Encoded Fringe-Adjusted Joint Transform Correlator
Abstract: A new target detection technique is presented in this
paper for the identification of small boats in coastal surveillance. The
proposed technique employs an adaptive progressive thresholding (APT) scheme to first process the given input scene to separate any
objects present in the scene from the background. The preprocessing
step results in an image having only the foreground objects, such as
boats, trees and other cluttered regions, and hence reduces the search
region for the correlation step significantly. The processed image is then fed to the shifted phase-encoded fringe-adjusted joint transform
correlator (SPFJTC) technique which produces single and delta-like
correlation peak for a potential target present in the input scene. A
post-processing step involves using a peak-to-clutter ratio (PCR) to determine whether the boat in the input scene is authorized or unauthorized. Simulation results are presented to show that the
proposed technique can successfully determine the presence of an authorized boat and identify any intruding boat present in the given input scene.
Digital Article Identifier (DOI):
167
1606
Eclectic Rule-Extraction from Support Vector Machines
Abstract: Support vector machines (SVMs) have shown
superior performance compared to other machine learning techniques,
especially in classification problems. Yet one limitation of SVMs is
the lack of an explanation capability which is crucial in some
applications, e.g. in the medical and security domains. In this paper, a
novel approach for eclectic rule-extraction from support vector
machines is presented. This approach utilizes the knowledge acquired
by the SVM and represented in its support vectors as well as the
parameters associated with them. The approach includes three stages;
training, propositional rule-extraction and rule quality evaluation.
Results from four different experiments have demonstrated the value
of the approach for extracting comprehensible rules of high accuracy
and fidelity.
Digital Article Identifier (DOI):
166
9066
Feature Subset Selection Using Ant Colony Optimization
Abstract: Feature selection is an important step in many pattern
classification problems. It is applied to select a subset of features,
from a much larger set, such that the selected subset is sufficient to
perform the classification task. Due to its importance, the problem of
feature selection has been investigated by many researchers. In this
paper, a novel feature subset search procedure that utilizes the Ant
Colony Optimization (ACO) is presented. The ACO is a
metaheuristic inspired by the behavior of real ants in their search for
the shortest paths to food sources. It looks for optimal solutions by
considering both local heuristics and previous knowledge. When
applied to two different classification problems, the proposed
algorithm achieved very promising results.
Digital Article Identifier (DOI):
165
9816
Design of Genetic-Algorithm Based Robust Power System Stabilizer
Abstract: This paper presents a systematic approach for the
design of power system stabilizer using genetic algorithm and
investigates the robustness of the GA based PSS. The proposed
approach employs GA search for optimal setting of PSS parameters.
The performance of the proposed GPSS under small and large
disturbances, loading conditions and system parameters is tested.
The eigenvalue analysis and nonlinear simulation results show the
effectiveness of the GPSS to damp out the system oscillations. It is
found tat the dynamic performance with the GPSS shows improved
results, over conventionally tuned PSS over a wide range of
operating conditions.
Digital Article Identifier (DOI):
164
713
Neural Networks Approaches for Computing the Forward Kinematics of a Redundant Parallel Manipulator
Abstract: In this paper, different approaches to solve the
forward kinematics of a three DOF actuator redundant hydraulic
parallel manipulator are presented. On the contrary to series
manipulators, the forward kinematic map of parallel manipulators
involves highly coupled nonlinear equations, which are almost
impossible to solve analytically. The proposed methods are using
neural networks identification with different structures to solve the
problem. The accuracy of the results of each method is analyzed in
detail and the advantages and the disadvantages of them in
computing the forward kinematic map of the given mechanism is
discussed in detail. It is concluded that ANFIS presents the best
performance compared to MLP, RBF and PNN networks in this
particular application.
Digital Article Identifier (DOI):
163
9353
Discovering Complex Regularities: from Tree to Semi-Lattice Classifications
Abstract: Data mining uses a variety of techniques each of which
is useful for some particular task. It is important to have a deep
understanding of each technique and be able to perform sophisticated
analysis. In this article we describe a tool built to simulate a variation
of the Kohonen network to perform unsupervised clustering and
support the entire data mining process up to results visualization. A
graphical representation helps the user to find out a strategy to
optimize classification by adding, moving or delete a neuron in order
to change the number of classes. The tool is able to automatically
suggest a strategy to optimize the number of classes optimization, but
also support both tree classifications and semi-lattice organizations of
the classes to give to the users the possibility of passing from one
class to the ones with which it has some aspects in common.
Examples of using tree and semi-lattice classifications are given to
illustrate advantages and problems. The tool is applied to classify
macroeconomic data that report the most developed countries- import
and export. It is possible to classify the countries based on their
economic behaviour and use the tool to characterize the commercial
behaviour of a country in a selected class from the analysis of
positive and negative features that contribute to classes formation.
Possible interrelationships between the classes and their meaning are
also discussed.
Digital Article Identifier (DOI):
162
8136
Novel and Different Definitions for Fuzzy Union and Intersection Operations
Abstract: This paper presents three new methodologies for the
basic operations, which aim at finding new ways of computing union
(maximum) and intersection (minimum) membership values by
taking into effect the entire membership values in a fuzzy set. The
new methodologies are conceptually simple and easy from the
application point of view and are illustrated with a variety of
problems such as Cartesian product of two fuzzy sets, max –min
composition of two fuzzy sets in different product spaces and an
application of an inverted pendulum to determine the impact of the
new methodologies. The results clearly indicate a difference based on
the nature of the fuzzy sets under consideration and hence will be
highly useful in quite a few applications where different values have
significant impact on the behavior of the system.
Digital Article Identifier (DOI):
161
3218
Fast Complex Valued Time Delay Neural Networks
Abstract: Here, a new idea to speed up the operation of
complex valued time delay neural networks is presented. The whole
data are collected together in a long vector and then tested as a one
input pattern. The proposed fast complex valued time delay neural
networks uses cross correlation in the frequency domain between the
tested data and the input weights of neural networks. It is proved
mathematically that the number of computation steps required for
the presented fast complex valued time delay neural networks is less
than that needed by classical time delay neural networks. Simulation
results using MATLAB confirm the theoretical computations.
Digital Article Identifier (DOI):
160
12925
Integrating Visual Modeling throughout the Computer Science Curriculum
Abstract: The purposes of this paper are to (1) promote
excellence in computer science by suggesting a cohesive innovative
approach to fill well documented deficiencies in current computer
science education, (2) justify (using the authors- and others anecdotal
evidence from both the classroom and the real world) why this
approach holds great potential to successfully eliminate the
deficiencies, (3) invite other professionals to join the authors in proof
of concept research. The authors- experiences, though anecdotal,
strongly suggest that a new approach involving visual modeling
technologies should allow computer science programs to retain a
greater percentage of prospective and declared majors as students
become more engaged learners, more successful problem-solvers,
and better prepared as programmers. In addition, the graduates of
such computer science programs will make greater contributions to
the profession as skilled problem-solvers. Instead of wearily
rememorizing code as they move to the next course, students will
have the problem-solving skills to think and work in more
sophisticated and creative ways.
Digital Article Identifier (DOI):
159
10055
Electronic Government in the GCC Countries
Abstract: The study investigated the practices of organisations in Gulf Cooperation Council (GCC) countries with regards to G2C egovernment maturity. It reveals that e-government G2C initiatives in the surveyed countries in particular, and arguably around the world in general, are progressing slowly because of the lack of a trusted and secure medium to authenticate the identities of online users. The authors conclude that national ID schemes will play a major role in helping governments reap the benefits of e-government if the three advanced technologies of smart card, biometrics and public key infrastructure (PKI) are utilised to provide a reliable and trusted authentication medium for e-government services.
Digital Article Identifier (DOI):
158
9329
Impact of the Real Effective Exchange Rate (Reer) on Turkish Agricultural Trade
Abstract: In this work, the autoregressive vectors are used to
know dynamics of the Agricultural export and import, and the real
effective exchange rate (REER). In order to analyze the interactions,
the impulse- response function is used in decomposition of variance,
causality of Granger as well as the methodology of Johansen to know
the relations co integration. The REER causes agricultural export and
import in the sense of Granger. The influence displays the
innovations of the REER on the agricultural export and import is not
very great and the duration of the effects is short. It displays that
REER has an immediate positive effect, after the tenth year it
displays smooth results on the agricultural export. Evidence of a
vector exists co integration, In short run, REER has smaller effects
on export and import, compared to the long-run effects.
Digital Article Identifier (DOI):
157
6603
UAE National ID Programme Case Study
Abstract: This article provides some insight into the
implementation of the national ID programme in the United Arab
Emirates (UAE). The fundamental aim is to contribute to the
existing body of knowledge in the field, as it sheds light on some of
the lessons learned from the programme that is believed to widening
the knowledge horizons of those involved in such initiatives.
Digital Article Identifier (DOI):
156
4778
Gender based Barriers to Effective Collaboration: A Case Study on Children's Safeguard Partnerships
Abstract: This paper explores gender related barriers to interagency collaboration in statutory children safeguard partnerships against a theoretical framework that considers individuals, professions and organisations interacting as part of a complex adaptive system. We argue that gender-framed obstacles to effective communication between culturally discrepant agencies can ultimately impact on the effectiveness of policy delivery,. We focused our research on three partnership structures in Sefton Metropolitan Borough in order to observe how interactions occur, whether the agencies involved perceive their occupational environment as being gender affected and whether they believe this can hinder effective collaboration with other biased organisations. Our principal empirical findings indicate that there is a general awareness amongst professionals of the role that gender plays in each of the agencies reviewed, that gender may well constitute a barrier to effective communication, but there is a sense in which there is little scope for change in the short term. We aim to signal here, however, the need to change against the risk of service failure.
Digital Article Identifier (DOI):
155
12773
Development, Displacement and Rehabilitation: An Action Anthropological Study on Kovvada Reservoir in West Godavari Agency of Andhra Pradesh, India
Abstract: This paper discusses the issue of tribal development,
displacement, rehabilitation and resettlement policies, and
implementation in the agency (scheduled / tribal) areas of the West
Godavari District, Andhra Pradesh State, India. This study is based
on action anthropological approach, conducted among the displaced
tribal communities i.e. Konda Reddis and Nayakapods of this region,
under the 'Kovvada Reservoir' Project. These groups are
traditionally shifting cultivators and popularly known as the
Primitive Tribal Groups (PTGs) in the government records. This
paper also focuses on the issues of tribal displacement and land
alienation due to construction of the Kovvada reservoir, without
proper rehabilitation and resettlement, although there are well
defined guidelines, procedures and norms for the rehabilitation of
Project Affected Persons (PAPs). It is necessary to begin with, to
provide an overview of the issues in tribal development and policies
related to displacement and rehabilitation in the Indian context as a
background to the Kovvada Reservoir Project, the subject of this
study.
Digital Article Identifier (DOI):
154
9074
Relationship between Communication Effectiveness and the Extent of Communication among Organizational Units
Abstract: This contribution deals with the relationship between
communication effectiveness and the extent of communication
among organizational units. To facilitate communication between
employees and to increase the level of understanding, the knowledge
of communication tools is necessary. Recent experience has shown
that personal communication is critical for smooth running of
companies and cannot be fully replaced by any form of technical
communication devices.
Below are presented the outcomes of the research on the
relationship between the extent of communication among
organisational units and its efficiency.
Keywords: Company meetings,
corporate culture,
efficiency,
effective communication,
form of communication,
information,
organizational units,
quality of communication,
strategy,
subordinates,
superiors.
Digital Article Identifier (DOI):
153
15758
Accounting Research from the Globalization Perspective
Abstract: This paper explores the idea of globalisation and
considers accounting-s role in that process in order to develop new
spaces for accounting research. That-s why in this paper we are
looking for questions not necessary for answers. Adopting an
'alternative' view of accounting it-s related to the fact that we sees
accounting as social and evolutionist process, that pays heed to those
voices arguing for greater social and environmental justice, and that
draws attention to the role of accounting researchers in the process of
globalisation. The paper defines globalisation and expands the
globalisation and accounting research agenda introducing in this
context the harmonization process in accounting. There are the two
main systems which are disputing the first stage of being the
benchmark: GAAP and IFRS. Each of them has his pluses and
minuses on being the selected one. Due to this fact a convergence of
the two, joining the advantages and disadvantages of the two should
be the solution for an unique international accounting solution. Is this
idea realizable, what steps has been made until now, what should be
done in the future. The paper is emphasising the role of the cultural
differences in the process of imposing of an unique international
accounting system by the global organizations..
Digital Article Identifier (DOI):
152
15262
Re-Engineering the Human: New Reproductive Technologies and the Specter of Frankenstein
Abstract: The virulent debates that have dogged research on,
and the diffusion of, a wide range of technologies indicate a growing
loss of confidence in what we might call, the techno-scientific
endeavour to reshape the world. Utopian images of a world rendered
ever more amenable to human desires are now closely shadowed by
just as compelling dystopian visions of monstrosity and disaster that
are nevertheless constructed from the same cultural material. The
paper uses the case of the debates over developments in reproductive
technology to offer some observations on the ways in which such
technologies routinely become enmirred in cultural ambivalence.
Digital Article Identifier (DOI):
151
12223
Communication and Human Resource Management and its Compliance with Culture
Abstract: According to the conception of personnel
management, human resource management requires efficient use of
human resources. This is ensured by various activities directed
towards the area of management. Among these activities there are for
example the recruitment of employees, development, strengthening
of relations, mutual inspiring, implementation of correct working
processes and systems used by individuals or groups.
Digital Article Identifier (DOI):
150
7897
Managerial Styles of Asian Executives: The Case of Thailand
Abstract: This research project is developed in order to study
managerial styles of modern Thai executives. The thorough
understanding will lead to continuous improvement and efficient
performance of Thai business organizations. Regarding managerial
skills, Thai executives focus heavily upon human skills. Also, the
negotiator roles are most emphasis in their management. In addition,
Thai executives pay most attention to the fundamental management
principles including Harmony and Unity of Direction of the
organizations. Moreover, the management techniques, consisting of
Team work and Career Planning are of their main concern. Finally,
Thai executives wish to enhance their firms- image and employees-
morale through conducting the ethical and socially responsible
activities. The major tactic deployed to stimulate employees- ethical
behaviors and mindset is Code of Ethics development.
Digital Article Identifier (DOI):
149
6848
Integrated Method for Detection of Unknown Steganographic Content
Abstract: This article concerns the presentation of an integrated
method for detection of steganographic content embedded by new
unknown programs. The method is based on data mining and
aggregated hypothesis testing. The article contains the theoretical
basics used to deploy the proposed detection system and the
description of improvement proposed for the basic system idea.
Further main results of experiments and implementation details are
collected and described. Finally example results of the tests are
presented.
Keywords: Steganography,
steganalysis,
data embedding,
data
mining,
feature extraction,
knowledge base,
system learning,
hypothesis testing,
error estimation,
black box program,
file
structure.
Digital Article Identifier (DOI):
148
10968
Application of Fuzzy Logic in Fault Diagnosis in Transformers using Dissolved Gas based on Different Standards
Abstract: One of the problems in fault diagnosis of transformer
based on dissolved gas, is lack of matching the result of fault
diagnosis of different standards with the real world. In this paper, the
result of the different standards is analyzed using fuzzy and the result
is compared with the empirical test. The comparison between the
suggested method and existing methods indicate the capability of the
suggested method in on-line fault diagnosis of the transformers. In
addition, in some cases the existing standards are not able to
diagnose the fault. In theses cases, the presented method has the
potential of diagnosing the fault. The information of three
transformers is used to the show the capability of the suggested
method in diagnosing the fault. The results validate the capability of
the presented method in fault diagnosis of the transformer.
Digital Article Identifier (DOI):
147
2338
Transmission Pricing based on Voltage Angle Decomposition
Abstract: In this paper a new approach for transmission pricing
is presented. The main idea is voltage angle allocation, i.e.
determining the contribution of each contract on the voltage angle of
each bus. DC power flow is used to compute a primary solution for
angle decomposition. To consider the impacts of system non-linearity
on angle decomposition, the primary solution is corrected in different
iterations of decoupled Newton-Raphson power flow. Then, the
contribution of each contract on power flow of each transmission line
is computed based on angle decomposition. Contract-related flows
are used as a measure for “extent of use" of transmission network
capacity and consequently transmission pricing. The presented
approach is applied to a 4-bus test system and IEEE 30-bus test
system.
Digital Article Identifier (DOI):
146
11644
Mathematical Approach for Large Deformation Analysis of the Stiffened Coupled Shear Walls
Abstract: Shear walls are used in most of the tall buildings for
carrying the lateral load. When openings for doors or windows are
necessary to be existed in the shear walls, a special type of the shear
walls is used called "coupled shear walls" which in some cases is
stiffened by specific beams and so, called "stiffened coupled shear
walls".
In this paper, a mathematical method for geometrically nonlinear
analysis of the stiffened coupled shear walls has been presented.
Then, a suitable formulation for determining the critical load of the
stiffened coupled shear walls under gravity force has been proposed.
The governing differential equations for equilibrium and deformation
of the stiffened coupled shear walls have been obtained by setting up
the equilibrium equations and the moment-curvature relationships for
each wall. Because of the complexity of the differential equation, the
energy method has been adopted for approximate solution of the
equations.
Digital Article Identifier (DOI):
145
11148
Development of a Neural Network based Algorithm for Multi-Scale Roughness Parameters and Soil Moisture Retrieval
Abstract: The overall objective of this paper is to retrieve soil
surfaces parameters namely, roughness and soil moisture related to
the dielectric constant by inverting the radar backscattered signal
from natural soil surfaces.
Because the classical description of roughness using statistical
parameters like the correlation length doesn't lead to satisfactory
results to predict radar backscattering, we used a multi-scale
roughness description using the wavelet transform and the Mallat
algorithm. In this description, the surface is considered as a
superposition of a finite number of one-dimensional Gaussian
processes each having a spatial scale. A second step in this study
consisted in adapting a direct model simulating radar backscattering
namely the small perturbation model to this multi-scale surface
description. We investigated the impact of this description on radar
backscattering through a sensitivity analysis of backscattering
coefficient to the multi-scale roughness parameters.
To perform the inversion of the small perturbation multi-scale
scattering model (MLS SPM) we used a multi-layer neural network
architecture trained by backpropagation learning rule. The inversion
leads to satisfactory results with a relative uncertainty of 8%.
Digital Article Identifier (DOI):
144
3690
Modeling Approaches for Large-Scale Reconfigurable Engineering Systems
Abstract: This paper reviews various approaches that have been
used for the modeling and simulation of large-scale engineering
systems and determines their appropriateness in the development of a
RICS modeling and simulation tool. Bond graphs, linear graphs,
block diagrams, differential and difference equations, modeling
languages, cellular automata and agents are reviewed. This tool
should be based on linear graph representation and supports symbolic
programming, functional programming, the development of noncausal
models and the incorporation of decentralized approaches.
Digital Article Identifier (DOI):
143
7224
Transportation and Physical Development around Kumasi, Ghana
Abstract: This research explores the links between physical
development and transportation infrastructure around Kumasi,
Ghana. It utilizes census data as well as fieldwork and interviews
carried out during July and December 2005. The results suggest that
there is a weak association between transportation investments and
physical development, and that recent housing has generally occurred
in poorly accessible locations. Road investments have generally
followed physical expansion rather than the reverse. Hence policies
designed to manage the fast growth now occurring around Ghanaian
cities should not focus exclusively on improving transportation
infrastructure but also strengthening the underlying the traditional
land management structures and the official land administrative
institutions that operate within those structures.
Digital Article Identifier (DOI):
142
526
Improving Performance of World Wide Web by Adaptive Web Traffic Reduction
Abstract: The ever increasing use of World Wide Web in the
existing network, results in poor performance. Several techniques
have been developed for reducing web traffic by compressing the size
of the file, saving the web pages at the client side, changing the burst
nature of traffic into constant rate etc. No single method was
adequate enough to access the document instantly through the
Internet. In this paper, adaptive hybrid algorithms are developed for
reducing web traffic. Intelligent agents are used for monitoring the
web traffic. Depending upon the bandwidth usage, user-s preferences,
server and browser capabilities, intelligent agents use the best
techniques to achieve maximum traffic reduction. Web caching,
compression, filtering, optimization of HTML tags, and traffic
dispersion are incorporated into this adaptive selection. Using this
new hybrid technique, latency is reduced to 20 – 60 % and cache hit
ratio is increased 40 – 82 %.
Digital Article Identifier (DOI):
141
7745
An Improved Algorithm of SPIHT based on the Human Visual Characteristics
Abstract: Because of excellent properties, people has paid more
attention to SPIHI algorithm, which is based on the traditional wavelet
transformation theory, but it also has its shortcomings. Combined the
progress in the present wavelet domain and the human's visual
characteristics, we propose an improved algorithm based on human
visual characteristics of SPIHT in the base of analysis of SPIHI
algorithm. The experiment indicated that the coding speed and quality
has been enhanced well compared to the original SPIHT algorithm,
moreover improved the quality of the transmission cut off.
Digital Article Identifier (DOI):
140
3868
A Multimedia Telemonitoring Network for Healthcare
Abstract: TELMES project aims to develop a securized
multimedia system devoted to medical consultation teleservices. It
will be finalized with a pilot system for a regional telecenters
network that connects local telecenters, having as support
multimedia platforms. This network will enable the implementation
of complex medical teleservices (teleconsulations, telemonitoring,
homecare, urgency medicine, etc.) for a broader range of patients
and medical professionals, mainly for family doctors and those
people living in rural or isolated regions. Thus, a multimedia,
scalable network, based on modern IT&C paradigms, will result. It
will gather two inter-connected regional telecenters, in Iaşi and
Piteşti, Romania, each of them also permitting local connections of
hospitals, diagnostic and treatment centers, as well as local networks
of family doctors, patients, even educational entities. As
communications infrastructure, we aim to develop a combined fixmobile-
internet (broadband) links. Other possible communication
environments will be GSM/GPRS/3G and radio waves. The
electrocardiogram (ECG) acquisition, internet transmission and
local analysis, using embedded technologies, was already
successfully done for patients- telemonitoring.
Digital Article Identifier (DOI):
139
8832
Through Biometric Card in Romania: Person Identification by Face, Fingerprint and Voice Recognition
Abstract: In this paper three different approaches for person
verification and identification, i.e. by means of fingerprints, face and
voice recognition, are studied. Face recognition uses parts-based
representation methods and a manifold learning approach. The
assessment criterion is recognition accuracy. The techniques under
investigation are: a) Local Non-negative Matrix Factorization
(LNMF); b) Independent Components Analysis (ICA); c) NMF with
sparse constraints (NMFsc); d) Locality Preserving Projections
(Laplacianfaces). Fingerprint detection was approached by classical
minutiae (small graphical patterns) matching through image
segmentation by using a structural approach and a neural network as
decision block. As to voice / speaker recognition, melodic cepstral
and delta delta mel cepstral analysis were used as main methods, in
order to construct a supervised speaker-dependent voice recognition
system. The final decision (e.g. “accept-reject" for a verification
task) is taken by using a majority voting technique applied to the
three biometrics. The preliminary results, obtained for medium
databases of fingerprints, faces and voice recordings, indicate the
feasibility of our study and an overall recognition precision (about
92%) permitting the utilization of our system for a future complex
biometric card.
Digital Article Identifier (DOI):
138
634
Modeling Ambient Carbon Monoxide Pollutant Due to Road Traffic
Abstract: Rapid urbanization, industrialization and population
growth have led to an increase in number of automobiles that cause
air pollution. It is estimated that road traffic contributes 60% of air
pollution in urban areas. A case by case assessment is required to
predict the air quality in urban situations, so as to evolve certain
traffic management measures to maintain the air quality levels with
in the tolerable limits. Calicut city in the state of Kerala, India has
been chosen as the study area. Carbon Monoxide (CO) concentration
was monitored at 15 links in Calicut city and air quality performance
was evaluated over each link. The CO pollutant concentration values
were compared with the National Ambient Air Quality Standards
(NAAQS), and the CO values were predicted by using CALINE4 and
IITLS and Linear regression models. The study has revealed that
linear regression model performs better than the CALINE4 and
IITLS models. The possible association between CO pollutant
concentration and traffic parameters like traffic flow, type of vehicle,
and traffic stream speed was also evaluated.
Digital Article Identifier (DOI):
137
5112
A Watermarking System Using the Wavelet Technique for Satellite Images
Abstract: The huge development of new technologies and the
apparition of open communication system more and more
sophisticated create a new challenge to protect digital content from
piracy. Digital watermarking is a recent research axis and a new
technique suggested as a solution to these problems. This technique
consists in inserting identification information (watermark) into
digital data (audio, video, image, databases...) in an invisible and
indelible manner and in such a way not to degrade original medium-s
quality. Moreover, we must be able to correctly extract the
watermark despite the deterioration of the watermarked medium (i.e
attacks). In this paper we propose a system for watermarking satellite
images. We chose to embed the watermark into frequency domain,
precisely the discrete wavelet transform (DWT). We applied our
algorithm on satellite images of Tunisian center. The experiments
show satisfying results. In addition, our algorithm showed an
important resistance facing different attacks, notably the compression
(JEPG, JPEG2000), the filtering, the histogram-s manipulation and
geometric distortions such as rotation, cropping, scaling.
Digital Article Identifier (DOI):
136
1692
Average Switching Thresholds and Average Throughput for Adaptive Modulation using Markov Model
Abstract: The motivation for adaptive modulation and coding is
to adjust the method of transmission to ensure that the maximum
efficiency is achieved over the link at all times. The receiver
estimates the channel quality and reports it back to the transmitter.
The transmitter then maps the reported quality into a link mode. This
mapping however, is not a one-to-one mapping. In this paper we
investigate a method for selecting the proper modulation scheme.
This method can dynamically adapt the mapping of the Signal-to-
Noise Ratio (SNR) into a link mode. It enables the use of the right
modulation scheme irrespective of changes in the channel conditions
by incorporating errors in the received data. We propose a Markov
model for this method, and use it to derive the average switching
thresholds and the average throughput. We show that the average
throughput of this method outperforms the conventional threshold
method.
Digital Article Identifier (DOI):
135
1709
Visualisation Techniques Connecting VRML and GENESIS Environments
Abstract: We created the tool, which combines the powerful
GENESIS (GEneral NEural SImulation System) simulation language
with the up-to-date visualisation and internet techniques. Our
solution resides in the connection between the simulation output from
GENESIS, which is converted to the data-structure suitable for
WWW browsers and VRML (Virtual Reality Modelling Language)
viewers. The selected GENESIS simulations are once exported into
the VRML code, and stored in our neurovisualisation portal
(webserver). There, the loaded models, demonstrating mainly the
spread of electrical signal (action potentials, postsynaptic potentials)
along the neuronal membrane (axon, dendritic tree, neuron) could be
displayed in the client-s VRML viewer, without interacting with
original GENESIS environment. This enables the visualisation of
basic neurophysiological phenomena designed for GENESIS
simulator on the independent OS (operation system).
Digital Article Identifier (DOI):
134
3417
An Agent-Based Approach to Immune Modelling: Priming Individual Response
Abstract: This study focuses on examining why the range of
experience with respect to HIV infection is so diverse, especially in
regard to the latency period. An agent-based approach in modelling
the infection is used to extract high-level behaviour which cannot be
obtained analytically from the set of interaction rules at the cellular
level. A prototype model encompasses local variation in baseline
properties, contributing to the individual disease experience, and is
included in a network which mimics the chain of lymph nodes. The
model also accounts for stochastic events such as viral mutations.
The size and complexity of the model require major computational
effort and parallelisation methods are used.
Digital Article Identifier (DOI):
133
9247
Finding Authoritative Researchers on Academic Web Sites
Abstract: In this paper, we present a methodology for finding
authoritative researchers by analyzing academic Web sites. We show
a case study in which we concentrate on a set of Czech computer
science departments- Web sites. We analyze the relations between
them via hyperlinks and find the most important ones using several
common ranking algorithms. We then examine the contents of the
research papers present on these sites and determine the most
authoritative Czech authors.
Digital Article Identifier (DOI):
132
15595
Observations about the Principal Components Analysis and Data Clustering Techniques in the Study of Medical Data
Abstract: The medical data statistical analysis often requires the
using of some special techniques, because of the particularities of
these data. The principal components analysis and the data clustering
are two statistical methods for data mining very useful in the medical
field, the first one as a method to decrease the number of studied
parameters, and the second one as a method to analyze the
connections between diagnosis and the data about the patient-s
condition. In this paper we investigate the implications obtained from
a specific data analysis technique: the data clustering preceded by a
selection of the most relevant parameters, made using the principal
components analysis. Our assumption was that, using the principal
components analysis before data clustering - in order to select and to
classify only the most relevant parameters – the accuracy of
clustering is improved, but the practical results showed the opposite
fact: the clustering accuracy decreases, with a percentage
approximately equal with the percentage of information loss reported
by the principal components analysis.
Digital Article Identifier (DOI):
131
4523
A Neural Computing-Based Approach for the Early Detection of Hepatocellular Carcinoma
Abstract: Hepatocellular carcinoma, also called hepatoma, most
commonly appears in a patient with chronic viral hepatitis. In
patients with a higher suspicion of HCC, such as small or subtle
rising of serum enzymes levels, the best method of diagnosis
involves a CT scan of the abdomen, but only at high cost. The aim of
this study was to increase the ability of the physician to early detect
HCC, using a probabilistic neural network-based approach, in order
to save time and hospital resources.
Digital Article Identifier (DOI):
130
7050
Image Compression with Back-Propagation Neural Network using Cumulative Distribution Function
Abstract: Image Compression using Artificial Neural Networks
is a topic where research is being carried out in various directions
towards achieving a generalized and economical network.
Feedforward Networks using Back propagation Algorithm adopting
the method of steepest descent for error minimization is popular and
widely adopted and is directly applied to image compression.
Various research works are directed towards achieving quick
convergence of the network without loss of quality of the restored
image. In general the images used for compression are of different
types like dark image, high intensity image etc. When these images
are compressed using Back-propagation Network, it takes longer
time to converge. The reason for this is, the given image may
contain a number of distinct gray levels with narrow difference with
their neighborhood pixels. If the gray levels of the pixels in an image
and their neighbors are mapped in such a way that the difference in
the gray levels of the neighbors with the pixel is minimum, then
compression ratio as well as the convergence of the network can be
improved. To achieve this, a Cumulative distribution function is
estimated for the image and it is used to map the image pixels. When
the mapped image pixels are used, the Back-propagation Neural
Network yields high compression ratio as well as it converges
quickly.
Digital Article Identifier (DOI):
129
10582
An Improved Resource Discovery Approach Using P2P Model for Condor: A Grid Middleware
Abstract: Resource Discovery in Grids is critical for efficient
resource allocation and management. Heterogeneous nature and
dynamic availability of resources make resource discovery a
challenging task. As numbers of nodes are increasing from tens to
thousands, scalability is essentially desired. Peer-to-Peer (P2P)
techniques, on the other hand, provide effective implementation of
scalable services and applications. In this paper we propose a model
for resource discovery in Condor Middleware by using the four axis
framework defined in P2P approach. The proposed model enhances
Condor to incorporate functionality of a P2P system, thus aim to
make Condor more scalable, flexible, reliable and robust.
Digital Article Identifier (DOI):
128
7383
Improving the Reusability and Interoperability of E-Learning Material
Abstract: A key requirement for e-learning materials is
reusability and interoperability, that is the possibility to use at least
part of the contents in different courses, and to deliver them trough
different platforms. These features make possible to limit the cost of
new packages, but require the development of material according to
proper specifications. SCORM (Sharable Content Object Reference
Model) is a set of guidelines suitable for this purpose. A specific
adaptation project has been started to make possible to reuse existing
materials. The paper describes the main characteristics of SCORM
specification, and the procedure used to modify the existing material.
Digital Article Identifier (DOI):
127
13894
E-learning for Professional Education of Personnel in a Hospital
Abstract: A collaboration among the Hospital S. Giovanni Battista
of Turin, the Politecnico of Turin, and the MUST company is
described. The content of the collaboration has been and is the use of
ICT-s, e-learning, and blended learning for the internal professional
education, training, and keeping up to date of the personnel of the
hospital. A platform for the delivery of the teaching materials has
been built, including an evaluation and self-evaluation tool. The first
on line courses have been developed and delivered and many more
are in preparation. The first results of the monitoring of the efficacy
of the online education have been positive.
Digital Article Identifier (DOI):
126
11092
Texture Feature Extraction using Slant-Hadamard Transform
Abstract: Random and natural textures classification is still
one of the biggest challenges in the field of image processing and
pattern recognition. In this paper, texture feature extraction using
Slant Hadamard Transform was studied and compared to other
signal processing-based texture classification schemes. A
parametric SHT was also introduced and employed for natural
textures feature extraction. We showed that a subtly modified
parametric SHT can outperform ordinary Walsh-Hadamard
transform and discrete cosine transform. Experiments were carried
out on a subset of Vistex random natural texture images using a
kNN classifier.
Digital Article Identifier (DOI):
125
6432
Feature Reduction of Nearest Neighbor Classifiers using Genetic Algorithm
Abstract: The design of a pattern classifier includes an attempt
to select, among a set of possible features, a minimum subset of
weakly correlated features that better discriminate the pattern classes.
This is usually a difficult task in practice, normally requiring the
application of heuristic knowledge about the specific problem
domain. The selection and quality of the features representing each
pattern have a considerable bearing on the success of subsequent
pattern classification. Feature extraction is the process of deriving
new features from the original features in order to reduce the cost of
feature measurement, increase classifier efficiency, and allow higher
classification accuracy. Many current feature extraction techniques
involve linear transformations of the original pattern vectors to new
vectors of lower dimensionality. While this is useful for data
visualization and increasing classification efficiency, it does not
necessarily reduce the number of features that must be measured
since each new feature may be a linear combination of all of the
features in the original pattern vector. In this paper a new approach is
presented to feature extraction in which feature selection, feature
extraction, and classifier training are performed simultaneously using
a genetic algorithm. In this approach each feature value is first
normalized by a linear equation, then scaled by the associated weight
prior to training, testing, and classification. A knn classifier is used to
evaluate each set of feature weights. The genetic algorithm optimizes
a vector of feature weights, which are used to scale the individual
features in the original pattern vectors in either a linear or a nonlinear
fashion. By this approach, the number of features used in classifying
can be finely reduced.
Digital Article Identifier (DOI):
124
11907
Using Non-Linear Programming Techniques in Determination of the Most Probable Slip Surface in 3D Slopes
Abstract: Among many different methods that are used for
optimizing different engineering problems mathematical (numerical)
optimization techniques are very important because they can easily
be used and are consistent with most of engineering problems. Many
studies and researches are done on stability analysis of three
dimensional (3D) slopes and the relating probable slip surfaces and
determination of factors of safety, but in most of them force
equilibrium equations, as in simplified 2D methods, are considered
only in two directions. In other words for decreasing mathematical
calculations and also for simplifying purposes the force equilibrium
equation in 3rd direction is omitted. This point is considered in just a
few numbers of previous studies and most of them have only given a
factor of safety and they haven-t made enough effort to find the most
probable slip surface. In this study shapes of the slip surfaces are
modeled, and safety factors are calculated considering the force
equilibrium equations in all three directions, and also the moment
equilibrium equation is satisfied in the slip direction, and using
nonlinear programming techniques the shape of the most probable
slip surface is determined. The model which is used in this study is a
3D model that is composed of three upper surfaces which can cover
all defined and probable slip surfaces. In this research the meshing
process is done in a way that all elements are prismatic with
quadrilateral cross sections, and the safety factor is defined on this
quadrilateral surface in the base of the element which is a part of the
whole slip surface. The method that is used in this study to find the
most probable slip surface is the non-linear programming method in
which the objective function that must get optimized is the factor of
safety that is a function of the soil properties and the coordinates of
the nodes on the probable slip surface. The main reason for using
non-linear programming method in this research is its quick
convergence to the desired responses. The final results show a good
compatibility with the previously used classical and 2D methods and
also show a reasonable convergence speed.
Digital Article Identifier (DOI):
123
12751
Application of Mapping and Superimposing Rule for Solution of Parabolic PDE in Porous Medium under Cyclic Loading
Abstract: This paper presents an analytical method to solve
governing consolidation parabolic partial differential equation (PDE)
for inelastic porous Medium (soil) with consideration of variation of
equation coefficient under cyclic loading. Since under cyclic loads,
soil skeleton parameters change, this would introduce variable
coefficient of parabolic PDE. Classical theory would not rationalize
consolidation phenomenon in such condition. In this research, a
method based on time space mapping to a virtual time space along
with superimposing rule is employed to solve consolidation of
inelastic soils in cyclic condition. Changes of consolidation
coefficient applied in solution by modification of loading and
unloading duration by introducing virtual time. Mapping function is
calculated based on consolidation partial differential equation results.
Based on superimposing rule a set of continuous static loads in
specified times used instead of cyclic load. A set of laboratory
consolidation tests under cyclic load along with numerical
calculations were performed in order to verify the presented method.
Numerical solution and laboratory tests results showed accuracy of
presented method.
Digital Article Identifier (DOI):
122
7878
Studies on Automatic Measurement Technology for Surface Braided Angle of Three-Dimensional Braided Composite Material Performs
Abstract: This paper describes a new measuring algorithm for
three-dimensional (3-D) braided composite material .Braided angle is
an important parameter of braided composites. The objective of this
paper is to present an automatic measuring system. In the paper, the
algorithm is performed by using vcµ6.0 language on PC. An
advanced filtered algorithm for image of 3-D braided composites
material performs has been developed. The procedure is completely
automatic and relies on the gray scale information content of the
images and their local wavelet transform modulus maxims.
Experimental results show that the proposed method is feasible.
The algorithm was tested on both carbon-fiber and glass-fiber
performs.
Digital Article Identifier (DOI):
121
10884
Advanced Information Extraction with n-gram based LSI
Abstract: Number of documents being created increases at an
increasing pace while most of them being in already known topics
and little of them introducing new concepts. This fact has started a
new era in information retrieval discipline where the requirements
have their own specialties. That is digging into topics and concepts
and finding out subtopics or relations between topics. Up to now IR
researches were interested in retrieving documents about a general
topic or clustering documents under generic subjects. However these
conventional approaches can-t go deep into content of documents
which makes it difficult for people to reach to right documents they
were searching. So we need new ways of mining document sets
where the critic point is to know much about the contents of the
documents. As a solution we are proposing to enhance LSI, one of
the proven IR techniques by supporting its vector space with n-gram
forms of words. Positive results we have obtained are shown in two
different application area of IR domain; querying a document
database, clustering documents in the document database.
Digital Article Identifier (DOI):
120
8821
Using Genetic Algorithm to Improve Information Retrieval Systems
Abstract: This study investigates the use of genetic algorithms
in information retrieval. The method is shown to be applicable to
three well-known documents collections, where more relevant
documents are presented to users in the genetic modification. In this
paper we present a new fitness function for approximate information
retrieval which is very fast and very flexible, than cosine similarity
fitness function.
Digital Article Identifier (DOI):
119
2372
Applications of Genetic Programming in Data Mining
Abstract: This paper details the application of a genetic
programming framework for induction of useful classification rules
from a database of income statements, balance sheets, and cash flow
statements for North American public companies. Potentially
interesting classification rules are discovered. Anomalies in the
discovery process merit further investigation of the application of
genetic programming to the dataset for the problem domain.
Digital Article Identifier (DOI):
118
2687
Adequacy of Object-Oriented Framework System-Based Testing Techniques
Abstract: An application framework provides a reusable design
and implementation for a family of software systems. If the
framework contains defects, the defects will be passed on to the
applications developed from the framework. Framework defects are
hard to discover at the time the framework is instantiated. Therefore,
it is important to remove all defects before instantiating the
framework. In this paper, two measures for the adequacy of an
object-oriented system-based testing technique are introduced. The
measures assess the usefulness and uniqueness of the testing
technique. The two measures are applied to experimentally compare
the adequacy of two testing techniques introduced to test objectoriented
frameworks at the system level. The two considered testing
techniques are the New Framework Test Approach and Testing
Frameworks Through Hooks (TFTH). The techniques are also
compared analytically in terms of their coverage power of objectoriented
aspects. The comparison study results show that the TFTH
technique is better than the New Framework Test Approach in terms
of usefulness degree, uniqueness degree, and coverage power.
Digital Article Identifier (DOI):
117
5383
Simultaneous Tuning of Static Var Compensator and Power System Stabilizer Employing Real- Coded Genetic Algorithm
Abstract: Power system stability enhancement by simultaneous tuning of a Power System Stabilizer (PSS) and a Static Var Compensator (SVC)-based controller is thoroughly investigated in this paper. The coordination among the proposed damping stabilizers and the SVC internal voltage regulators has also been taken into consideration. The design problem is formulated as an optimization problem with a time-domain simulation-based objective function and Real-Coded Genetic Algorithm (RCGA) is employed to search for optimal controller parameters. The proposed stabilizers are tested on a weakly connected power system with different disturbances and loading conditions. The nonlinear simulation results are presented to show the effectiveness and robustness of the proposed control schemes over a wide range of loading conditions and disturbances. Further, the proposed design approach is found to be robust and improves stability effectively even under small disturbance and unbalanced fault conditions.
Digital Article Identifier (DOI):
116
1296
Optimization of Transmission Lines Loading in TNEP Using Decimal Codification Based GA
Abstract: Transmission network expansion planning (TNEP) is a basic part of power system planning that determines where, when and how many new transmission lines should be added to the network. Up till now, various methods have been presented to solve the static transmission network expansion planning (STNEP) problem. But in all of these methods, lines adequacy rate has not been considered at the end of planning horizon, i.e., expanded network misses adequacy after some times and needs to be expanded again. In this paper, expansion planning has been implemented by merging lines loading parameter in the STNEP and inserting investment cost into the fitness function constraints using genetic algorithm. Expanded network will possess a maximum adequacy to provide load demand and also the transmission lines overloaded later. Finally, adequacy index could be defined and used to compare some designs that have different investment costs and adequacy rates. In this paper, the proposed idea has been tested on the Garvers network. The results show that the network will possess maximum efficiency economically.
Digital Article Identifier (DOI):
115
12942
Multimachine Power System Stabilizers Design Using PSO Algorithm
Abstract: In this paper, multiobjective design of multi-machine Power System Stabilizers (PSSs) using Particle Swarm Optimization (PSO) is presented. The stabilizers are tuned to simultaneously shift the lightly damped and undamped electro-mechanical modes of all machines to a prescribed zone in the s-plane. A multiobjective problem is formulated to optimize a composite set of objective functions comprising the damping factor, and the damping ratio of the lightly damped electromechanical modes. The PSSs parameters tuning problem is converted to an optimization problem which is solved by PSO with the eigenvalue-based multiobjective function. The proposed PSO based PSSs is tested on a multimachine power system under different operating conditions and disturbances through eigenvalue analysis and some performance indices to illustrate its robust performance.
Digital Article Identifier (DOI):
114
12951
A Novel Optimal Setting for Directional over Current Relay Coordination using Particle Swarm Optimization
Abstract: Over Current Relays (OCRs) and Directional Over Current Relays (DOCRs) are widely used for the radial protection and ring sub transmission protection systems and for distribution systems. All previous work formulates the DOCR coordination problem either as a Non-Linear Programming (NLP) for TDS and Ip or as a Linear Programming (LP) for TDS using recently a social behavior (Particle Swarm Optimization techniques) introduced to the work. In this paper, a Modified Particle Swarm Optimization (MPSO) technique is discussed for the optimal settings of DOCRs in power systems as a Non-Linear Programming problem for finding Ip values of the relays and for finding the TDS setting as a linear programming problem. The calculation of the Time Dial Setting (TDS) and the pickup current (Ip) setting of the relays is the core of the coordination study. PSO technique is considered as realistic and powerful solution schemes to obtain the global or quasi global optimum in optimization problem.
Digital Article Identifier (DOI):
113
2652
A Novel Method for Behavior Modeling in Uncertain Information Systems
Abstract: None of the processing models in the software
development has explained the software systems performance
evaluation and modeling; likewise, there exist uncertainty in the
information systems because of the natural essence of requirements,
and this may cause other challenges in the processing of software
development. By definition an extended version of UML (Fuzzy-
UML), the functional requirements of the software defined
uncertainly would be supported. In this study, the behavioral
description of uncertain information systems by the aid of fuzzy-state
diagram is crucial; moreover, the introduction of behavioral diagrams
role in F-UML is investigated in software performance modeling
process. To get the aim, a fuzzy sub-profile is used.
Digital Article Identifier (DOI):
112
3920
Comanche – A Compiler-Driven I/O Management System
Abstract: Most scientific programs have large input and output
data sets that require out-of-core programming or use virtual memory
management (VMM). Out-of-core programming is very error-prone
and tedious; as a result, it is generally avoided. However, in many
instance, VMM is not an effective approach because it often results
in substantial performance reduction. In contrast, compiler driven I/O
management will allow a program-s data sets to be retrieved in parts,
called blocks or tiles. Comanche (COmpiler MANaged caCHE) is a
compiler combined with a user level runtime system that can be used
to replace standard VMM for out-of-core programs. We describe
Comanche and demonstrate on a number of representative problems
that it substantially out-performs VMM. Significantly our system
does not require any special services from the operating system and
does not require modification of the operating system kernel.
Digital Article Identifier (DOI):
111
14414
Generating Class-Based Test Cases for Interface Classes of Object-Oriented Gray-Box Frameworks
Abstract: An application framework provides a reusable design
and implementation for a family of software systems. Application
developers extend the framework to build their particular
applications using hooks. Hooks are the places identified to show
how to use and customize the framework. Hooks define Framework
Interface Classes (FICs) and their possible specifications, which
helps in building reusable test cases for the implementations of these
classes. In applications developed using gray-box frameworks, FICs
inherit framework classes or use them without inheritance. In this
paper, a test-case generation technique is extended to build test cases
for FICs built for gray-box frameworks. A tool is developed to
automate the introduced technique.
Digital Article Identifier (DOI):
110
12903
Hybrid GA Tuned RBF Based Neuro-Fuzzy Controller for Robotic Manipulator
Abstract: In this paper performance of Puma 560
manipulator is being compared for hybrid gradient descent
and least square method learning based ANFIS controller with
hybrid Genetic Algorithm and Generalized Pattern Search
tuned radial basis function based Neuro-Fuzzy controller.
ANFIS which is based on Takagi Sugeno type Fuzzy
controller needs prior knowledge of rule base while in radial
basis function based Neuro-Fuzzy rule base knowledge is not
required. Hybrid Genetic Algorithm with generalized Pattern
Search is used for tuning weights of radial basis function
based Neuro- fuzzy controller. All the controllers are checked
for butterfly trajectory tracking and results in the form of
Cartesian and joint space errors are being compared. ANFIS
based controller is showing better performance compared to
Radial Basis Function based Neuro-Fuzzy Controller but rule
base independency of RBF based Neuro-Fuzzy gives it an
edge over ANFIS
Digital Article Identifier (DOI):
109
12237
Effect of Transmission Codes on Hybrid SC/MRC Diversity Reception MQAM system over Rayleigh Fading Channels
Abstract: In this paper, the effect of transmission codes on the
performance of coherent square M-ary quadrature amplitude
modulation (CSMQAM) under hybrid selection/maximal-ratio
combining (H-S/MRC) diversity is analysed. The fading channels are
modeled as frequency non-selective slow independent and identically
distributed Rayleigh fading channels corrupted by additive white
Gaussian noise (AWGN). The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM under H-S/MRC diversity by
plotting error probabilities versus average signal to noise ratio (SNR)
for various values L and N in order to examine the improvement in
the performance of the digital communications system as the number
of selected diversity branches is increased. The results for no
diversity, conventional SC and Lth order MRC schemes are also
plotted for comparison. Closed form analytical results derived in this
paper are sufficiently simple and therefore can be computed
numerically without any approximations. The analytical results
presented in this paper are expected to provide useful information
needed for design and analysis of digital communication systems
over wireless fading channels.
Digital Article Identifier (DOI):
108
14735
Using Rao-Blackwellised Particle Filter Track 3D Arm Motion based on Hierarchical Limb Model
Abstract: For improving the efficiency of human 3D tracking, we
present an algorithm to track 3D Arm Motion. First, the Hierarchy
Limb Model (HLM) is proposed based on the human 3D skeleton
model. Second, via graph decomposition, the arm motion state space,
modeled by HLM, can be discomposed into two low dimension
subspaces: root nodes and leaf nodes. Finally, Rao-Blackwellised
Particle Filter is used to estimate the 3D arm motion. The result of
experiment shows that our algorithm can advance the computation
efficiency.
Digital Article Identifier (DOI):
107
12596
Adaptive Early Packet Discarding Policy Based on Two Traffic Classes
Abstract: Unlike the best effort service provided by the internet
today, next-generation wireless networks will support real-time
applications. This paper proposes an adaptive early packet discard
(AEPD) policy to improve the performance of the real time TCP
traffic over ATM networks and avoid the fragmentation problem.
Three main aspects are incorporated in the proposed policy. First,
providing quality-of-service (QoS) guaranteed for real-time
applications by implementing a priority scheduling. Second,
resolving the partially corrupted packets problem by differentiating
the buffered cells of one packet from another. Third, adapting a
threshold dynamically using Fuzzy logic based on the traffic
behavior to maintain a high throughput under a variety of load
conditions. The simulation is run for two priority classes of the input
traffic: real time and non-real time classes. Simulation results show
that the proposed AEPD policy improves throughput and fairness
over that using static threshold under the same traffic conditions.
Digital Article Identifier (DOI):
106
8190
Increased Capacity of Information Hiding in LSB-s Method for Text and Image
Abstract: Steganography, derived from Greek, literally means
“covered writing". It includes a vast array of secret communications
methods that conceal the message-s very existence. These methods
include invisible inks, microdots, character arrangement, digital
signatures, covert channels, and spread spectrum communications.
This paper proposes a new improved version of Least Significant Bit
(LSB) method. The approach proposed is simple for implementation
when compared to Pixel value Differencing (PVD) method and yet
achieves a High embedding capacity and imperceptibility. The
proposed method can also be applied to 24 bit color images and
achieve embedding capacity much higher than PVD.
Digital Article Identifier (DOI):
105
8513
Design of Digital Differentiator to Optimize Relative Error
Abstract: It is observed that the Weighted least-square (WLS)
technique, including the modifications, results in equiripple error
curve. The resultant error as a percent of the ideal value is highly
non-uniformly distributed over the range of frequencies for which the
differentiator is designed. The present paper proposes a modification
to the technique so that the optimization procedure results in lower
maximum relative error compared to the ideal values. Simulation
results for first order as well as higher order differentiators are given
to illustrate the excellent performance of the proposed method.
Digital Article Identifier (DOI):
104
14977
High Level Characterization and Optimization of Switched-Current Sigma-Delta Modulators with VHDL-AMS
Abstract: Today, design requirements are extending more and
more from electronic (analogue and digital) to multidiscipline design.
These current needs imply implementation of methodologies to make
the CAD product reliable in order to improve time to market, study
costs, reusability and reliability of the design process.
This paper proposes a high level design approach applied for the
characterization and the optimization of Switched-Current Sigma-
Delta Modulators. It uses the new hardware description language
VHDL-AMS to help the designers to optimize the characteristics of
the modulator at a high level with a considerably reduced CPU time
before passing to a transistor level characterization.
Digital Article Identifier (DOI):
103
12990
A 24-Bit, 8.1-MS/s D/A Converter for Audio Baseband Channel Applications
Abstract: This paper study the high-level modelling and design
of delta-sigma (ΔΣ) noise shapers for audio Digital-to-Analog
Converter (DAC) so as to eliminate the in-band Signal-to-Noise-
Ratio (SNR) degradation that accompany one channel mismatch in
audio signal. The converter combines a cascaded digital signal
interpolation, a noise-shaping single loop delta-sigma modulator with
a 5-bit quantizer resolution in the final stage. To reduce sensitivity of
Digital-to-Analog Converter (DAC) nonlinearities of the last stage, a
high pass second order Data Weighted Averaging (R2DWA) is
introduced. This paper presents a MATLAB description modelling
approach of the proposed DAC architecture with low distortion and
swing suppression integrator designs. The ΔΣ Modulator design can
be configured as a 3rd-order and allows 24-bit PCM at sampling rate
of 64 kHz for Digital Video Disc (DVD) audio application. The
modeling approach provides 139.38 dB of dynamic range for a 32
kHz signal band at -1.6 dBFS input signal level.
Digital Article Identifier (DOI):
102
14939
Environmental Interference Cancellation of Speech with the Radial Basis Function Networks: An Experimental Comparison
Abstract: In this paper, we use Radial Basis Function Networks
(RBFN) for solving the problem of environmental interference
cancellation of speech signal. We show that the Second Order Thin-
Plate Spline (SOTPS) kernel cancels the interferences effectively.
For make comparison, we test our experiments on two conventional
most used RBFN kernels: the Gaussian and First order TPS (FOTPS)
basis functions. The speech signals used here were taken from the
OGI Multi-Language Telephone Speech Corpus database and were
corrupted with six type of environmental noise from NOISEX-92
database. Experimental results show that the SOTPS kernel can
considerably outperform the Gaussian and FOTPS functions on
speech interference cancellation problem.
Digital Article Identifier (DOI):
101
13170
Enhanced GA-Fuzzy OPF under both Normal and Contingent Operation States
Abstract: The genetic algorithm (GA) based solution techniques
are found suitable for optimization because of their ability of
simultaneous multidimensional search. Many GA-variants have been
tried in the past to solve optimal power flow (OPF), one of the
nonlinear problems of electric power system. The issues like
convergence speed and accuracy of the optimal solution obtained
after number of generations using GA techniques and handling
system constraints in OPF are subjects of discussion. The results
obtained for GA-Fuzzy OPF on various power systems have shown
faster convergence and lesser generation costs as compared to other
approaches. This paper presents an enhanced GA-Fuzzy OPF (EGAOPF)
using penalty factors to handle line flow constraints and load
bus voltage limits for both normal network and contingency case
with congestion. In addition to crossover and mutation rate
adaptation scheme that adapts crossover and mutation probabilities
for each generation based on fitness values of previous generations, a
block swap operator is also incorporated in proposed EGA-OPF. The
line flow limits and load bus voltage magnitude limits are handled by
incorporating line overflow and load voltage penalty factors
respectively in each chromosome fitness function. The effects of
different penalty factors settings are also analyzed under contingent
state.
Digital Article Identifier (DOI):
100
15492
Ohmic Quality Factor and Efficiency Estimation for a Gyrotron Cavity
Abstract: Operating a device at high power and high frequency
is a major problem because wall losses greatly reduce the efficiency
of the device. In the present communication, authors analytically
analyzed the dependence of ohmic/RF efficiency, the fraction of
output power with respect to the total power generated, of gyrotron
cavity structure on the conductivity of copper for the second
harmonic TE0,6 mode. This study shows a rapid fall in the RF
efficiency as the quality (conductivity) of copper degrades. Starting
with an RF efficiency near 40% at the conductivity of ideal copper
(5.8 x 107 S/m), the RF efficiency decreases (upto 8%) as the copper
quality degrades. Assuming conductivity half that of ideal copper the
RF efficiency as a function of diffractive quality factor, Qdiff, has
been studied. Here the RF efficiency decreases rapidly with
increasing diffractive Q. Ohmic wall losses as a function of
frequency for 460 GHz gyrotron cavity excited in TE0,6 mode has
also been analyzed. For 460 GHz cavity, the extracted power is
reduced to 32% of the generated power due to ohmic losses in the
walls of the cavity.
Digital Article Identifier (DOI):
99
5025
Eigenwave Analysis and Simulation of Disc Loaded Interaction Structure for Wideband Gyro-TWT Amplifier
Abstract: In the present paper, disc loaded interaction structure
for potential application in wideband Gyro-TWT amplifier has been
analyzed, taking all the space and modal harmonics into
consideration, for the eigenwave solutions. The analysis has been
restricted to azimuthally symmetric TE0,n mode. Dispersion
characteristics have been plotted by varying the structure parameters
and have been validated against HFSS simulation results. The
variation of eigenvalue with respect to different structure parameters
has also been presented. It has been observed that disc periodicity
plays very important role for wideband operation of disc-loaded
Gyro-TWT.
Digital Article Identifier (DOI):
98
3803
Creating the Color Panoramic View using Medley of Grayscale and Color Partial Images
Abstract: Panoramic view generation has always offered
novel and distinct challenges in the field of image processing.
Panoramic view generation is nothing but construction of bigger
view mosaic image from set of partial images of the desired view.
The paper presents a solution to one of the problems of image
seascape formation where some of the partial images are color and
others are grayscale. The simplest solution could be to convert all
image parts into grayscale images and fusing them to get grayscale
image panorama. But in the multihued world, obtaining the colored
seascape will always be preferred. This could be achieved by picking
colors from the color parts and squirting them in grayscale parts of
the seascape. So firstly the grayscale image parts should be colored
with help of color image parts and then these parts should be fused to
construct the seascape image.
The problem of coloring grayscale images has no exact solution.
In the proposed technique of panoramic view generation, the job of
transferring color traits from reference color image to grayscale
image is done by palette based method. In this technique, the color
palette is prepared using pixel windows of some degrees taken from
color image parts. Then the grayscale image part is divided into pixel
windows with same degrees. For every window of grayscale image
part the palette is searched and equivalent color values are found,
which could be used to color grayscale window. For palette
preparation we have used RGB color space and Kekre-s LUV color
space. Kekre-s LUV color space gives better quality of coloring. The
searching time through color palette is improved over the exhaustive
search using Kekre-s fast search technique.
After coloring the grayscale image pieces the next job is fusion of
all these pieces to obtain panoramic view. For similarity estimation
between partial images correlation coefficient is used.
Digital Article Identifier (DOI):
97
7857
Using Interval Constrained Petri Nets for the Fuzzy Regulation of Quality: Case of Assembly Process Mechanics
Abstract: The indistinctness of the manufacturing processes makes that a parts cannot be realized in an absolutely exact way towards the specifications on the dimensions. It is thus necessary to assume that the effectively realized product has to belong in a very strict way to compatible intervals with a correct functioning of the parts. In this paper we present an approach based on mixing tow different characteristics theories, the fuzzy system and Petri net system. This tool has been proposed to model and control the quality in an assembly system. A robust command of a mechanical assembly process is presented as an application. This command will then have to maintain the specifications interval of parts in front of the variations. It also illustrates how the technique reacts when the product quality is high, medium, or low.
Digital Article Identifier (DOI):
96
12796
Phase Jitter Transfer in High Speed Data Links
Abstract: Phase locked loops in 10 Gb/s and faster data links are
low phase noise devices. Characterization of their phase jitter
transfer functions is difficult because the intrinsic noise of the PLLs
is comparable to the phase noise of the reference clock signal. The
problem is solved by using a linear model to account for the intrinsic
noise. This study also introduces a novel technique for measuring the
transfer function. It involves the use of the reference clock as a
source of wideband excitation, in contrast to the commonly used
sinusoidal excitations at discrete frequencies. The data reported here
include the intrinsic noise of a PLL for 10 Gb/s links and the jitter
transfer function of a PLL for 12.8 Gb/s links. The measured transfer
function suggests that the PLL responded like a second order linear
system to a low noise reference clock.
Digital Article Identifier (DOI):
95
2145
Analysis of Effect of Pre-Logic Factoring on Cell Based Combinatorial Logic Synthesis
Abstract: In this paper, an analysis is presented, which
demonstrates the effect pre-logic factoring could have on an
automated combinational logic synthesis process succeeding it. The
impact of pre-logic factoring for some arbitrary combinatorial
circuits synthesized within a FPGA based logic design environment
has been analyzed previously. This paper explores a similar effect,
but with the non-regenerative logic synthesized using elements of a
commercial standard cell library. On an overall basis, the results
obtained pertaining to the analysis on a variety of MCNC/IWLS
combinational logic benchmark circuits indicate that pre-logic
factoring has the potential to facilitate simultaneous power, delay and
area optimized synthesis solutions in many cases.
Digital Article Identifier (DOI):
94
9651
Stability Analysis of a Class of Nonlinear Systems Using Discrete Variable Structures and Sliding Mode Control
Abstract: This paper presents the application of discrete-time
variable structure control with sliding mode based on the 'reaching
law' method for robust control of a 'simple inverted pendulum on
moving cart' - a standard nonlinear benchmark system. The
controllers designed using the above techniques are completely
insensitive to parametric uncertainty and external disturbance. The
controller design is carried out using pole placement technique to find
state feedback gain matrix , which decides the dynamic behavior
of the system during sliding mode. This is followed by feedback gain
realization using the control law which is synthesized from 'Gao-s
reaching law'. The model of a single inverted pendulum and the
discrete variable structure control controller are developed, simulated
in MATLAB-SIMULINK and results are presented. The response of
this simulation is compared with that of the discrete linear quadratic
regulator (DLQR) and the advantages of sliding mode controller over
DLQR are also presented
Digital Article Identifier (DOI):
93
885
Comparative Study of Fault Identification and Classification on EHV Lines Using Discrete Wavelet Transform and Fourier Transform Based ANN
Abstract: An appropriate method for fault identification and classification on extra high voltage transmission line using discrete wavelet transform is proposed in this paper. The sharp variations of the generated short circuit transient signals which are recorded at the sending end of the transmission line are adopted to identify the fault. The threshold values involve fault classification and these are done on the basis of the multiresolution analysis. A comparative study of the performance is also presented for Discrete Fourier Transform (DFT) based Artificial Neural Network (ANN) and Discrete Wavelet Transform (DWT). The results prove that the proposed method is an effective and efficient one in obtaining the accurate result within short duration of time by using Daubechies 4 and 9. Simulation of the power system is done using MATLAB.
Digital Article Identifier (DOI):
92
15644
A New Algorithm for Enhanced Robustness of Copyright Mark
Abstract: This paper discusses a new heavy tailed distribution based data hiding into discrete cosine transform (DCT) coefficients of image, which provides statistical security as well as robustness against steganalysis attacks. Unlike other data hiding algorithms, the proposed technique does not introduce much effect in the stegoimage-s DCT coefficient probability plots, thus making the presence of hidden data statistically undetectable. In addition the proposed method does not compromise on hiding capacity. When compared to the generic block DCT based data-hiding scheme, our method found more robust against a variety of image manipulating attacks such as filtering, blurring, JPEG compression etc.
Digital Article Identifier (DOI):
91
10545
A Novel Zero Voltage Transition Synchronous Buck Converter for Portable Application
Abstract: This paper proposes a zero-voltage transition (ZVT) PWM synchronous buck converter, which is designed to operate at low output voltage and high efficiency typically required for portable systems. To make the DC-DC converter efficient at lower voltage, synchronous converter is an obvious choice because of lower conduction loss in the diode. The high-side MOSFET is dominated by the switching losses and it is eliminated by the soft switching technique. Additionally, the resonant auxiliary circuit designed is also devoid of the switching losses. The suggested procedure ensures an efficient converter. Theoretical analysis, computer simulation, and experimental results are presented to explain the proposed schemes.
Digital Article Identifier (DOI):
90
13526
PUMA 560 Optimal Trajectory Control using Genetic Algorithm, Simulated Annealing and Generalized Pattern Search Techniques
Abstract: Robot manipulators are highly coupled nonlinear
systems, therefore real system and mathematical model of dynamics
used for control system design are not same. Hence, fine-tuning of
controller is always needed. For better tuning fast simulation speed
is desired. Since, Matlab incorporates LAPACK to increase the speed
and complexity of matrix computation, dynamics, forward and
inverse kinematics of PUMA 560 is modeled on Matlab/Simulink in
such a way that all operations are matrix based which give very less
simulation time. This paper compares PID parameter tuning using
Genetic Algorithm, Simulated Annealing, Generalized Pattern Search
(GPS) and Hybrid Search techniques. Controller performances for all
these methods are compared in terms of joint space ITSE and
cartesian space ISE for tracking circular and butterfly trajectories.
Disturbance signal is added to check robustness of controller. GAGPS
hybrid search technique is showing best results for tuning PID
controller parameters in terms of ITSE and robustness.
Digital Article Identifier (DOI):
89
4907
Study on Ultrasonic Vibration Effects on Grinding Process of Alumina Ceramic (Al2O3)
Abstract: Nowadays, engineering ceramics have significant
applications in different industries such as; automotive, aerospace,
electrical, electronics and even martial industries due to their
attractive physical and mechanical properties like very high hardness
and strength at elevated temperatures, chemical stability, low friction
and high wear resistance. However, these interesting properties plus
low heat conductivity make their machining processes too hard,
costly and time consuming. Many attempts have been made in order
to make the grinding process of engineering ceramics easier and
many scientists have tried to find proper techniques to economize
ceramics' machining processes. This paper proposes a new diamond
plunge grinding technique using ultrasonic vibration for grinding
Alumina ceramic (Al2O3). For this purpose, a set of laboratory
equipments have been designed and simulated using Finite Element
Method (FEM) and constructed in order to be used in various
measurements. The results obtained have been compared with the
conventional plunge grinding process without ultrasonic vibration
and indicated that the surface roughness and fracture strength
improved and the grinding forces decreased.
Digital Article Identifier (DOI):
88
1586
Adjustment of a PET Scanner for PEPT
Abstract: Positron emission particle tracking (PEPT) is a
technique in which a single radioactive tracer particle can be
accurately tracked as it moves. A limitation of PET is that in order to
reconstruct a tomographic image it is necessary to acquire a large
volume of data (millions of events), so it is difficult to study rapidly
changing systems. By considering this fact, PEPT is a very fast
process compared with PET.
In PEPT detecting both photons defines a line and the annihilation
is assumed to have occurred somewhere along this line. The location
of the tracer can be determined to within a few mm from coincident
detection of a small number of pairs of back-to-back gamma rays and
using triangulation. This can be achieved many times per second and
the track of a moving particle can be reliably followed. This
technique was invented at the University of Birmingham [1].
The attempt in PEPT is not to form an image of the tracer particle
but simply to determine its location with time. If this tracer is
followed for a long enough period within a closed, circulating system
it explores all possible types of motion.
The application of PEPT to industrial process systems carried out
at the University of Birmingham is categorized in two subjects: the
behaviour of granular materials and viscous fluids. Granular
materials are processed in industry for example in the manufacture of
pharmaceuticals, ceramics, food, polymers and PEPT has been used
in a number of ways to study the behaviour of these systems [2].
PEPT allows the possibility of tracking a single particle within the
bed [3]. Also PEPT has been used for studying systems such as: fluid
flow, viscous fluids in mixers [4], using a neutrally-buoyant tracer
particle [5].
Digital Article Identifier (DOI):
87
4472
Experimental Estimation of Mixed-Mode Fracture Properties of Steel Weld
Abstract: The modified Arcan fixture was used in order to
investigate the mixed mode fracture properties of high strength steel
butt weld through experimental and numerical analysis. The fixture
consisted of a central section with "butterfly-shaped" specimen that
had central crack. The specimens were under pure mode I (opening),
pure mode II (shearing) and all in plane mixed mode loading angles
starting from 0 to 90 degrees. The geometric calibration factors were
calculated with the aid of finite element analysis for various loading
mode and different crack length (0.45≤ a/w ≤0.55) and the critical
fracture loads obtained experimentally. The critical fracture
toughness (KIC & KIIC) estimated with experimental and numerical
analysis under mixed mode loading conditions.
Digital Article Identifier (DOI):
86
6531
Mixed-Mode Study of Rock Fracture Mechanics by using the Modified Arcan Specimen Test
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Digital Article Identifier (DOI):
85
3600
Stress Analysis of Adhesively Bonded Double- Lap Joints Subjected to Combined Loading
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Digital Article Identifier (DOI):
84
7429
Numerical Investigation of Delamination in Carbon-Epoxy Composite using Arcan Specimen
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Digital Article Identifier (DOI):
83
12688
Continuous and Discontinuous Shock Absorber Control through Skyhook Strategy in Semi-Active Suspension System (4DOF Model)
Abstract: Active vibration isolation systems are less commonly
used than passive systems due to their associated cost and power
requirements. In principle, semi-active isolation systems can deliver
the versatility, adaptability and higher performance of fully active
systems for a fraction of the power consumption. Various semi-active
control algorithms have been suggested in the past. This paper
studies the 4DOF model of semi-active suspension performance
controlled by on–off and continuous skyhook damping control
strategy. The frequency and transient responses of model are
evaluated in terms of body acceleration, roll angle and tire deflection
and are compared with that of a passive damper. The results show
that the semi-active system controlled by skyhook strategy always
provides better isolation than a conventional passively damped
system except at tire natural frequencies.
Digital Article Identifier (DOI):
82
4703
Fracture Toughness Characterization of Carbon-Epoxy Composite using Arcan Specimen
Abstract: In this study the behavior of interlaminar fracture of
carbon-epoxy thermoplastic laminated composite is investigated
numerically and experimentally. Tests are performed with Arcan
specimens. Testing with Arcan specimen gives the opportunity of
utilizing just one kind of specimen for extracting fracture properties
for mode I, mode II and different mixed mode ratios of materials with
exerting load via different loading angles. Variation of loading angles
in range of 0-90° made possible to achieve different mixed mode
ratios. Correction factors for various conditions are obtained from
ABAQUS 2D finite element models which demonstrate the finite
shape of Arcan specimens used in this study. Finally, applying the
correction factors to critical loads obtained experimentally, critical
interlaminar fracture toughness of this type of carbon- epoxy
composite has been attained.
Digital Article Identifier (DOI):
81
3151
Geometry Calibration Factors of Modified Arcan Fracture Test for Welded Joint
Abstract: In this study the mixed mode fracture mechanics
parameters were investigated for high tensile steel butt welded joint
based on modified Arcan test and finite element analysis was used to
evaluate the effect of crack length on fracture criterion. The nondimensional
stress intensity factors, strain energy release rates and Jintegral
energy on crack tip were obtained for various in-plane
loading combinations on Arcan specimen starting from pure mode-I
to pure mode-II loading conditions. The specimen and apparatus were
modeled by finite element method and analyzed under various
loading angles (between 0 to 90 degrees with 15 degree interval) to
simulate the pure mode-I, II and mixed mode fracture. Since the
analytical results are independent from elasticity modules for
isotropic materials, therefore the results in elastic fields can be used
for Arcan specimens. The main objective of this study was to
evaluate the geometric calibration factors for modified Arcan test
specimen in order to obtain fracture toughness under mixed mode
loading conditions.
Digital Article Identifier (DOI):
80
6541
Prediction of the Epileptic Events 'Epileptic Seizures' by Neural Networks and Expert Systems
Abstract: Many studies have focused on the nonlinear analysis
of electroencephalography (EEG) mainly for the characterization of
epileptic brain states. It is assumed that at least two states of the
epileptic brain are possible: the interictal state characterized by a
normal apparently random, steady-state EEG ongoing activity; and
the ictal state that is characterized by paroxysmal occurrence of
synchronous oscillations and is generally called in neurology, a
seizure.
The spatial and temporal dynamics of the epileptogenic process is
still not clear completely especially the most challenging aspects of
epileptology which is the anticipation of the seizure. Despite all the
efforts we still don-t know how and when and why the seizure
occurs. However actual studies bring strong evidence that the
interictal-ictal state transition is not an abrupt phenomena. Findings
also indicate that it is possible to detect a preseizure phase.
Our approach is to use the neural network tool to detect interictal
states and to predict from those states the upcoming seizure ( ictal
state). Analysis of the EEG signal based on neural networks is used
for the classification of EEG as either seizure or non-seizure. By
applying prediction methods it will be possible to predict the
upcoming seizure from non-seizure EEG.
We will study the patients admitted to the epilepsy monitoring
unit for the purpose of recording their seizures. Preictal, ictal, and
post ictal EEG recordings are available on such patients for analysis
The system will be induced by taking a body of samples then
validate it using another. Distinct from the two first ones a third body
of samples is taken to test the network for the achievement of
optimum prediction. Several methods will be tried 'Backpropagation
ANN' and 'RBF'.
Digital Article Identifier (DOI):
79
10012
The Adoption and Diffusion of Electronic Wallets
Abstract: Despite the strong and consistent increase in the use of
electronic payment methods worldwide, the diffusion of electronic
wallets is still far from widespread. Analysis of the failure of
electronic wallet uptake has either focused on technical issues or
chosen to analyse a specific scheme. This article proposes a joint
approach to analysing key factors affecting the adoption of e-wallets
by using the ‘Technology Acceptance Model” [1] which we have
expanded to take into account the cost of using e-wallets. We use this
model to analyse Monéo, the only French electronic wallet still in
operation.
Digital Article Identifier (DOI):
78
2788
A ±0.5V BiCMOS Class-A Current Conveyor
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Digital Article Identifier (DOI):
77
3912
A New Recognition Scheme for Machine- Printed Arabic Texts based on Neural Networks
Abstract: This paper presents a new approach to tackle the problem of recognizing machine-printed Arabic texts. Because of the difficulty of recognizing cursive Arabic words, the text has to be normalized and segmented to be ready for the recognition stage. The new scheme for recognizing Arabic characters depends on multiple parallel neural networks classifier. The classifier has two phases. The first phase categories the input character into one of eight groups. The second phase classifies the character into one of the Arabic character classes in the group. The system achieved high recognition rate.
Digital Article Identifier (DOI):
76
6118
Client Server System for e-Services Access Using Mobile Communications Networks
Abstract: The client server systems using mobile
communications networks for data transmission became very
attractive for many economic agents, in the purpose of promoting and
offering electronic services to their clients. E-services are suitable for
business developing and financial benefits increasing. The products
or services can be efficiently delivered to a large number of clients,
using mobile Internet access technologies. The clients can have
access to e-services, anywhere and anytime, with the support of 3G,
GPRS, WLAN, etc., channels bandwidth, data services and protocols.
Based on the mobile communications networks evolution and
development, a convergence of technological and financial interests
of mobile operators, software developers, mobile terminals producers
and e-content providers is established. These will lead to a high level
of integration of IT&C resources and will facilitate the value added
services delivery through the mobile communications networks. In
this paper it is presented a client server system, for e-services access,
with Smartphones and PDA-s mobile software applications, installed
on Symbian and Windows Mobile operating systems.
Digital Article Identifier (DOI):
75
10341
The Influence of the Commons Structure Modification on the Active Power Losses Allocation
Abstract: The tracing methods determine the contribution the
power system sources have in their supplying. These methods can be
used to assess the transmission prices, but also to recover the
transmission fixed cost. In this paper is presented the influence of the
modification of commons structure has on the specific price of transfer
and on active power losses. The authors propose a power losses
allocation method, based on Kirschen-s method. The system operator
must make use of a few basic principles about allocation. The only
necessary information is the power flows on system branches and the
modifications applied to power system buses. In order to illustrate this
method, the 25-bus test system is used, elaborated within the Electrical
Power Engineering Department, from Timisoara, Romania.
Digital Article Identifier (DOI):
74
3808
1-D Modeling of Hydrate Decomposition in Porous Media
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Digital Article Identifier (DOI):
73
985
Improvement of Synchronous Machine Dynamic Characteristics via Neural Network Based Controllers
Abstract: This paper presents Simulation and experimental
study aimed at investigating the effectiveness of an adaptive artificial
neural network stabilizer on enhancing the damping torque of a
synchronous generator. For this purpose, a power system comprising
a synchronous generator feeding a large power system through a
short tie line is considered. The proposed adaptive neuro-control
system consists of two multi-layered feed forward neural networks,
which work as a plant model identifier and a controller. It generates
supplementary control signals to be utilized by conventional
controllers. The details of the interfacing circuits, sensors and
transducers, which have been designed and built for use in tests, are
presented. The synchronous generator is tested to investigate the
effect of tuning a Power System Stabilizer (PSS) on its dynamic
stability. The obtained simulation and experimental results verify the
basic theoretical concepts.
Digital Article Identifier (DOI):
72
1756
Approximation of Sturm-Liouville Problems by Exponentially Weighted Legendre-Gauss Tau Method
Abstract: We construct an exponentially weighted Legendre- Gauss Tau method for solving differential equations with oscillatory solutions. The proposed method is applied to Sturm-Liouville problems. Numerical examples illustrating the efficiency and the high accuracy of our results are presented.
Digital Article Identifier (DOI):
71
2258
Dynamics and Control of Bouncing Ball
Abstract: This paper investigates the control of a bouncing
ball using Model Predictive Control. Bouncing ball is a benchmark
problem for various rhythmic tasks such as juggling, walking,
hopping and running. Humans develop intentions which may be
perceived as our reference trajectory and tries to track it. The
human brain optimizes the control effort needed to track its
reference; this forms the central theme for control of bouncing ball
in our investigations.
Digital Article Identifier (DOI):
70
6927
Improved Root-Mean-Square-Gain-Combining for SIMO Channels
Abstract: The major problem that wireless communication
systems undergo is multipath fading caused by scattering of the
transmitted signal. However, we can treat multipath propagation as
multiple channels between the transmitter and receiver to improve
the signal-to-scattering-noise ratio. While using Single Input
Multiple Output (SIMO) systems, the diversity receivers extract
multiple signal branches or copies of the same signal received from
different channels and apply gain combining schemes such as Root
Mean Square Gain Combining (RMSGC). RMSGC asymptotically
yields an identical performance to that of the theoretically optimal
Maximum Ratio Combining (MRC) for values of mean Signal-to-
Noise-Ratio (SNR) above a certain threshold value without the need
for SNR estimation. This paper introduces an improvement of
RMSGC using two different issues. We found that post-detection and
de-noising the received signals improve the performance of RMSGC
and lower the threshold SNR.
Digital Article Identifier (DOI):
69
8203
Parallel Joint Channel Coding and Cryptography
Abstract: Method of Parallel Joint Channel Coding and
Cryptography has been analyzed and simulated in this paper. The
method is an extension of Soft Input Decryption with feedback,
which is used for improvement of channel decoding of secured
messages. Parallel Joint Channel Coding and Cryptography results in
improved coding gain of channel decoding, which achieves more
than 2 dB. Such results are an implication of a combination of
receiver components and their interoperability.
Digital Article Identifier (DOI):
68
1056
Analysis of Public-Key Cryptography for Wireless Sensor Networks Security
Abstract: With the widespread growth of applications of
Wireless Sensor Networks (WSNs), the need for reliable security
mechanisms these networks has increased manifold. Many security
solutions have been proposed in the domain of WSN so far. These
solutions are usually based on well-known cryptographic
algorithms.
In this paper, we have made an effort to survey well known
security issues in WSNs and study the behavior of WSN nodes that
perform public key cryptographic operations. We evaluate time
and power consumption of public key cryptography algorithm for
signature and key management by simulation.
Digital Article Identifier (DOI):
67
2384
Method to Improve Channel Coding Using Cryptography
Abstract: A new approach for the improvement of coding gain
in channel coding using Advanced Encryption Standard (AES) and
Maximum A Posteriori (MAP) algorithm is proposed. This new
approach uses the avalanche effect of block cipher algorithm AES
and soft output values of MAP decoding algorithm. The performance
of proposed approach is evaluated in the presence of Additive White
Gaussian Noise (AWGN). For the verification of proposed approach,
computer simulation results are included.
Digital Article Identifier (DOI):
66
14419
Risk-Management by Numerical Pattern Analysis in Data-Mining
Abstract: In this paper a new method is suggested for risk
management by the numerical patterns in data-mining. These patterns
are designed using probability rules in decision trees and are cared to
be valid, novel, useful and understandable. Considering a set of
functions, the system reaches to a good pattern or better objectives.
The patterns are analyzed through the produced matrices and some
results are pointed out. By using the suggested method the direction
of the functionality route in the systems can be controlled and best
planning for special objectives be done.
Digital Article Identifier (DOI):
65
2466
A First Course in Numerical Methods with “Mathematica“
Abstract: In the present paper some recommendations for the
use of software package “Mathematica" in a basic numerical analysis
course are presented. The methods which are covered in the course
include solution of systems of linear equations, nonlinear equations
and systems of nonlinear equations, numerical integration,
interpolation and solution of ordinary differential equations. A set of
individual assignments developed for the course covering all the
topics is discussed in detail.
Digital Article Identifier (DOI):
64
1897
Trustworthy in Virtual Organization
Abstract: In open settings, the participants in virtual
organization are autonomous and there is no central authority to
ensure the felicity of their interactions. When agents interact in such
settings, each relies upon being able to model the trustworthiness of
the agents with whom it interacts. Fundamentally, such models must
consider the past behavior of the other parties in order to predict their
future behavior. Further, it is sensible for the agents to share
information via referrals to trustworthy agents. In this article, trust is
a bet on the future contingent actions of others" and enumerates six
major factors supporting it: (1) reputation, (2) performance, (3)
appearance, (4) accountability, (5) precommitment, and (6)
contextual facilitation.
Digital Article Identifier (DOI):
63
10275
Design and Development of an MPH Program for Distance Education Delivery
Abstract: The Master-s of Public Health (MPH) degree is
growing in popularity among a number of higher education
institutions throughout the world as a distance education graduate
program. This paper offers an overview of program design and
development strategies that promote successful distance delivery of
MPH programs. Design and development challenges are discussed in
terms of type of distance delivery, accreditation, student demand,
faculty development, user needs, course content, and marketing
strategies. The ongoing development of a distance education MPH
program at Utah State University will be used to highlight and
consider various aspects of this important but challenging process.
Digital Article Identifier (DOI):
62
13587
Systematic Analysis of Dynamic Association of Health Outcomes with Computer Usage for Office Staff
Abstract: This paper systematically investigates the timedependent
health outcomes for office staff during computer work
using the developed mathematical model. The model describes timedependent
health outcomes in multiple body regions associated with
computer usage. The association is explicitly presented with a doseresponse
relationship which is parametrized by body region
parameters. Using the developed model we perform extensive
investigations of the health outcomes statically and dynamically. We
compare the risk body regions and provide various severity rankings
of the discomfort rate changes with respect to computer-related
workload dynamically for the study population. Application of the
developed model reveals a wide range of findings. Such broad
spectrum of investigations in a single report literature is lacking.
Based upon the model analysis, it is discovered that the highest
average severity level of the discomfort exists in neck, shoulder, eyes,
shoulder joint/upper arm, upper back, low back and head etc. The
biggest weekly changes of discomfort rates are in eyes, neck, head,
shoulder, shoulder joint/upper arm and upper back etc. The fastest
discomfort rate is found in neck, followed by shoulder, eyes, head,
shoulder joint/upper arm and upper back etc. Most of our findings are
consistent with the literature, which demonstrates that the developed
model and results are applicable and valuable and can be utilized to
assess correlation between the amount of computer-related workload
and health risk.
Digital Article Identifier (DOI):
61
8129
Collaborative Document Evaluation: An Alternative Approach to Classic Peer Review
Abstract: Research papers are usually evaluated via peer
review. However, peer review has limitations in evaluating research
papers. In this paper, Scienstein and the new idea of 'collaborative
document evaluation' are presented. Scienstein is a project to
evaluate scientific papers collaboratively based on ratings, links,
annotations and classifications by the scientific community using the
internet. In this paper, critical success factors of collaborative
document evaluation are analyzed. That is the scientists- motivation
to participate as reviewers, the reviewers- competence and the
reviewers- trustworthiness. It is shown that if these factors are
ensured, collaborative document evaluation may prove to be a more
objective, faster and less resource intensive approach to scientific
document evaluation in comparison to the classical peer review
process. It is shown that additional advantages exist as collaborative
document evaluation supports interdisciplinary work, allows
continuous post-publishing quality assessments and enables the
implementation of academic recommendation engines. In the long
term, it seems possible that collaborative document evaluation will
successively substitute peer review and decrease the need for
journals.
Digital Article Identifier (DOI):
60
11219
Evaluation of Exerting Force on the Heating Surface Due to Bubble Ebullition in Subcooled Flow Boiling
Abstract: Vibration characteristics of subcooled flow boiling on
thin and long structures such as a heating rod were recently
investigated by the author. The results show that the intensity of the
subcooled boiling-induced vibration (SBIV) was influenced strongly
by the conditions of the subcooling temperature, linear power density
and flow velocity. Implosive bubble formation and collapse are the
main nature of subcooled boiling, and their behaviors are the only
sources to originate from SBIV. Therefore, in order to explain the
phenomenon of SBIV, it is essential to obtain reliable information
about bubble behavior in subcooled boiling conditions. This was
investigated at different conditions of coolant subcooling
temperatures of 25 to 75°C, coolant flow velocities of 0.16 to
0.53m/s, and linear power densities of 100 to 600 W/cm. High speed
photography at 13,500 frames per second was performed at these
conditions. The results show that even at the highest subcooling
condition, the absolute majority of bubbles collapse very close to the
surface after detaching from the heating surface. Based on these
observations, a simple model of surface tension and momentum
change is introduced to offer a rough quantitative estimate of the
force exerted on the heating surface during the bubble ebullition. The
formation of a typical bubble in subcooled boiling is predicted to
exert an excitation force in the order of 10-4 N.
Digital Article Identifier (DOI):
59
6736
Information Systems Outsourcing Reasons and Risks: An Empirical Study
Abstract: Outsourcing, a management practice strongly
consolidated within the area of Information Systems, is currently
going through a stage of unstoppable growth. This paper makes a
proposal about the main reasons which may lead firms to adopt
Information Systems Outsourcing. It will equally analyse the
potential risks that IS clients are likely to face. An additional
objective is to assess these reasons and risks in the case of large
Spanish firms, while simultaneously examining their evolution over
time.
Digital Article Identifier (DOI):
58
9536
Assessment of Pollution Reduction
Abstract: Environmental investments, including ecological
projects, relating to the protection of atmosphere are today a need.
However, investing in the environment should be based on rational
management rules. This comes across a problem of selecting a
method to assess substances reduced during projects. Therefore, a
method allowing for the assessment of decision rationality has to be
found.
The purpose of this article is to present and systematise pollution
reduction assessment methods and illustrate theoretical analyses with
empirical data.
Empirical results confirm theoretical considerations, which proved
that the only method for judging pollution reduction, free of apparent
disadvantages, is the Eco 99-ratio method. To make decisions on
environmental projects, financing institutions should take into
account a rationality rule. Therefore the Eco 99-ratio method could
be applied to make decisions relating to environmental investments in
the area of air protection.
Digital Article Identifier (DOI):
57
12441
Issues in Deploying Smart Antennas in Mobile Radio Networks
Abstract: With the exponentially increasing demand for
wireless communications the capacity of current cellular systems will
soon become incapable of handling the growing traffic. Since radio
frequencies are diminishing natural resources, there seems to be a
fundamental barrier to further capacity increase. The solution can be
found in smart antenna systems.
Smart or adaptive antenna arrays consist of an array of antenna
elements with signal processing capability, that optimize the
radiation and reception of a desired signal, dynamically. Smart
antennas can place nulls in the direction of interferers via adaptive
updating of weights linked to each antenna element. They thus cancel
out most of the co-channel interference resulting in better quality of
reception and lower dropped calls. Smart antennas can also track the
user within a cell via direction of arrival algorithms. This implies that
they are more advantageous than other antenna systems. This paper
focuses on few issues about the smart antennas in mobile radio
networks.
Digital Article Identifier (DOI):
56
15307
Optimum Cascaded Design for Speech Enhancement Using Kalman Filter
Abstract: Speech enhancement is the process of eliminating
noise and increasing the quality of a speech signal, which is
contaminated with other kinds of distortions. This paper is on
developing an optimum cascaded system for speech enhancement.
This aim is attained without diminishing any relevant speech
information and without much computational and time complexity.
LMS algorithm, Spectral Subtraction and Kalman filter have been
deployed as the main de-noising algorithms in this work. Since these
algorithms suffer from respective shortcomings, this work has been
undertaken to design cascaded systems in different combinations and
the evaluation of such cascades by qualitative (listening) and
quantitative (SNR) tests.
Digital Article Identifier (DOI):
55
9569
Efficient Boosting-Based Active Learning for Specific Object Detection Problems
Abstract: In this work, we present a novel active learning approach
for learning a visual object detection system. Our system
is composed of an active learning mechanism as wrapper around
a sub-algorithm which implement an online boosting-based learning
object detector. In the core is a combination of a bootstrap procedure
and a semi automatic learning process based on the online boosting
procedure. The idea is to exploit the availability of classifier during
learning to automatically label training samples and increasingly
improves the classifier. This addresses the issue of reducing labeling
effort meanwhile obtain better performance. In addition, we propose
a verification process for further improvement of the classifier.
The idea is to allow re-update on seen data during learning for
stabilizing the detector. The main contribution of this empirical study
is a demonstration that active learning based on an online boosting
approach trained in this manner can achieve results comparable or
even outperform a framework trained in conventional manner using
much more labeling effort. Empirical experiments on challenging data
set for specific object deteciton problems show the effectiveness of
our approach.
Digital Article Identifier (DOI):
54
7478
Component-based Segmentation of Words from Handwritten Arabic Text
Abstract: Efficient preprocessing is very essential for automatic
recognition of handwritten documents. In this paper, techniques on
segmenting words in handwritten Arabic text are presented. Firstly,
connected components (ccs) are extracted, and distances among
different components are analyzed. The statistical distribution of this
distance is then obtained to determine an optimal threshold for words
segmentation. Meanwhile, an improved projection based method is
also employed for baseline detection. The proposed method has been
successfully tested on IFN/ENIT database consisting of 26459
Arabic words handwritten by 411 different writers, and the results
were promising and very encouraging in more accurate detection of
the baseline and segmentation of words for further recognition.
Digital Article Identifier (DOI):
53
4832
Effect of Fuel Spray Angle on Soot Formation in Turbulent Spray Flames
Abstract: Results are presented from a combined experimental
and modeling study undertaken to understand the effect of fuel spray
angle on soot production in turbulent liquid spray flames. The
experimental work was conducted in a cylindrical laboratory furnace
at fuel spray cone angle of 30º, 45º and 60º. Soot concentrations
inside the combustor are measured by filter paper technique. The soot
concentration is modeled by using the soot particle number density
and the mass density based acetylene concentrations. Soot oxidation
occurred by both hydroxide radicals and oxygen molecules. The
comparison of calculated results against experimental measurements
shows good agreement. Both the numerical and experimental results
show that the peak value of soot and its location in the furnace
depend on fuel spray cone angle. An increase in spray angle enhances
the evaporating rate and peak temperature near the nozzle. Although
peak soot concentration increase with enhance of fuel spray angle but
soot emission from the furnace decreases.
Digital Article Identifier (DOI):
52
1146
Identifying Corporate Managerial Topics with Web Pages
Abstract: This paper has as its main aim to analyse how
corporate web pages can become an essential tool in order to detect
strategic trends by firms or sectors, and even a primary source for
benchmarking. This technique has made it possible to identify the key
issues in the strategic management of the most excellent large Spanish
firms and also to describe trends in their long-range planning, a way of
working that can be generalised to any country or firm group. More
precisely, two objectives were sought. The first one consisted in showing
the way in which corporate websites make it possible to obtain direct
information about the strategic variables which can define firms. This
tool is dynamic (since web pages are constantly updated) as well as
direct and reliable, since the information comes from the firm itself, not
from comments of third parties (such as journalists, academicians,
consultants...). When this information is analysed for a group of firms,
one can observe their characteristics in terms of both managerial tasks
and business management. As for the second objective, the methodology
proposed served to describe the corporate profile of the large Spanish
enterprises included in the Ibex35 (the Ibex35 or Iberia Index is the
reference index in the Spanish Stock Exchange and gathers periodically
the 35 most outstanding Spanish firms). An attempt is therefore made to
define the long-range planning that would be characteristic of the largest
Spanish firms.
Digital Article Identifier (DOI):
51
819
A Real Time Collision Avoidance Algorithm for Mobile Robot based on Elastic Force
Abstract: This present paper proposes the modified Elastic Strip
method for mobile robot to avoid obstacles with a real time system in
an uncertain environment. The method deals with the problem of
robot in driving from an initial position to a target position based on
elastic force and potential field force. To avoid the obstacles, the
robot has to modify the trajectory based on signal received from the
sensor system in the sampling times. It was evident that with the
combination of Modification Elastic strip and Pseudomedian filter to
process the nonlinear data from sensor uncertainties in the data
received from the sensor system can be reduced. The simulations and
experiments of these methods were carried out.
Digital Article Identifier (DOI):
50
6284
A New Analytical Approach for Free Vibration of Membrane from Wave Standpoint
Abstract: In this paper, an analytical approach for free vibration
analysis of rectangular and circular membranes is presented. The
method is based on wave approach. From wave standpoint vibration
propagate, reflect and transmit in a structure. Firstly, the propagation
and reflection matrices for rectangular and circular membranes are
derived. Then, these matrices are combined to provide a concise and
systematic approach to free vibration analysis of membranes.
Subsequently, the eigenvalue problem for free vibration of membrane
is formulated and the equation of membrane natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Digital Article Identifier (DOI):
49
3759
Design and Fabrication of a Column-Climber Robot (Koala Robot)
Abstract: This paper proposes a robot able to climb Columns.
This robot is not dependent on the diameter and material of the
columns. Some climbing robots have been designed up to now but
Koala robot was designed and fabricated for climbing columns
exclusively. Simple kinematics of climbing in the nature inspired us
to design this robot. We used two linear mechanisms to grip the
column. The gripper consists of a DC motor and a power screw
mechanism with a linear bushing as a guide. This mechanism
provides enough force to grip the column. In addition we needed an
actuator for climbing the column; hence, two pneumatic jacks were
used. All the mechanical parts were designed according to the
exerted forces and operational condition. The prototype can be
simply installed and controlled on the column by an inexperienced
operator. This robot is intended for inspection and surveillance of
pipes in oil industries and power poles in electric industries.
Digital Article Identifier (DOI):
48
10334
Solar Tracking System: More Efficient Use of Solar Panels
Abstract: This paper shows the potential system benefits of
simple tracking solar system using a stepper motor and light sensor.
This method is increasing power collection efficiency by developing
a device that tracks the sun to keep the panel at a right angle to its
rays. A solar tracking system is designed, implemented and
experimentally tested. The design details and the experimental results
are shown.
Digital Article Identifier (DOI):
47
3160
Compact Slotted Broadband Antenna for Wireless Applications
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Digital Article Identifier (DOI):
46
2036
The Functionality and Usage of CRM Systems
Abstract: Modern information and communication technologies
offer a variety of support options for the efficient handling of
customer relationships. CRM systems have been developed, which
are designed to support the processes in the areas of marketing, sales
and service. Along with technological progress, CRM systems are
constantly changing, i.e. the systems are continually enhanced by
new functions. However, not all functions are suitable for every
company because of different frameworks and business processes. In
this context the question arises whether or not CRM systems are
widely used in Austrian companies and which business processes are
most frequently supported by CRM systems. This paper aims to shed
light on the popularity of CRM systems in Austrian companies in
general and the use of different functions to support their daily
business. First of all, the paper provides a theoretical overview of the
structure of modern CRM systems and proposes a categorization of
currently available software functionality for collaborative,
operational and analytical CRM processes, which provides the
theoretical background for the empirical study. Apart from these
theoretical considerations, the paper presents the empirical results of
a field survey on the use of CRM systems in Austrian companies and
analyzes its findings.
Digital Article Identifier (DOI):
45
7963
Identification of the Electronic City Application Obstacles in Iran
Abstract: Amazing development of the information technology,
communications and internet expansion as well as the requirements
of the city managers to new ideas to run the city and higher
participation of the citizens encourage us to complete the electronic
city as soon as possible. The foundations of this electronic city are in
information technology. People-s participation in metropolitan
management is a crucial topic. Information technology does not
impede this matter. It can ameliorate populace-s participation and
better interactions between the citizens and the city managers.
Citizens can proffer their ideas, beliefs and votes through digital
mass media based upon the internet and computerization plexuses on
the topical matters to receive appropriate replies and services. They
can participate in urban projects by becoming cognizant of the city
views. The most significant challenges are as follows: information
and communicative management, altering citizens- views, as well as
legal and office documents
Electronic city obstacles have been identified in this research. The
required data were forgathered through questionnaires to identify the
barriers from a statistical community comprising specialists and
practitioners of the ministry of information technology and
communication, the municipality information technology
organization.
The conclusions demonstrate that the prioritized electronic city
application barriers in Iran are as follows:
The support quandaries (non-financial ones), behavioral, cultural
and educational plights, the security, legal and license predicaments,
the hardware, orismological and infrastructural curbs, the software
and fiscal problems.
Digital Article Identifier (DOI):
44
4350
User Acceptance of Location-based Services
Abstract: Location-based services (LBS) exploit the known
location of a user to provide services dependent on their geographic
context and personalized needs [1].
The development and arrival of broadband mobile data networks
supported with mobile terminals equipped with new location
technologies like GPS have finally created opportunities for
implementation of LBS applications. But, from the other side,
collecting location information data in general raises privacy
concerns.
This paper presents results from two surveys of LBS acceptance in
Croatia. The first survey was administered on 181 students, and the
second extended survey involved pattern of 180 Croatian citizens.
We developed questionnaire which consists of descriptions of 15
different applications with scale which measures perceptions and
attitudes of users towards these applications.
We report the results to identify potential commercial applications
for LBS in B2C segment. Our findings suggest that some types of
applications like emergency&safety services and navigation have
significantly higher rate of acceptance than other types.
Digital Article Identifier (DOI):
43
10999
Sufficiency Economy: A Contribution to Economic Development
Abstract: The Philosophy of Sufficiency Economy, bestowed
by His Majesty the King Bhumibol Adulyadej to the people of
Thailand, highlights a balanced way of living. Three principles of
moderation reasonableness, and immunity, along with the conditions
for morality and knowledge, can be applied to any level of the
society–from an individual to the nation. The Philosophy of
Sufficiency Economy helps address the current development
challenges, which are issues on institutions, environmental
sustainability, human well-being, and the role of the government.
Digital Article Identifier (DOI):
42
3358
An Exploration on On-line Mass Collaboration: Focusing on its Motivation Structure
Abstract: The Internet has become an indispensable part of our lives. Witnessing recent web-based mass collaboration, e.g. Wikipedia, people are questioning whether the Internet has made fundamental changes to the society or whether it is merely a hyperbolic fad. It has long been assumed that collective action for a certain goal yields the problem of free-riding, due to its non-exclusive and non-rival characteristics. Then, thanks to recent technological advances, the on-line space experienced the following changes that enabled it to produce public goods: 1) decrease in the cost of production or coordination 2) externality from networked structure 3) production function which integrates both self-interest and altruism. However, this research doubts the homogeneity of on-line mass collaboration and argues that a more sophisticated and systematical approach is required. The alternative that we suggest is to connect the characteristics of the goal to the motivation. Despite various approaches, previous literature fails to recognize that motivation can be structurally restricted by the characteristic of the goal. First we draw a typology of on-line mass collaboration with 'the extent of expected beneficiary' and 'the existence of externality', and then we examine each combination of motivation using Benkler-s framework. Finally, we explore and connect such typology with its possible dominant participating motivation.
Digital Article Identifier (DOI):
41
7474
Demand and Supply Chain Simulation in Telecommunication Industry by Multi-Rate Expert Systems
Abstract: In modern telecommunications industry, demand &
supply chain management (DSCM) needs reliable design and
versatile tools to control the material flow. The objective for efficient
DSCM is reducing inventory, lead times and related costs in order to
assure reliable and on-time deliveries from manufacturing units
towards customers. In this paper the multi-rate expert system based
methodology for developing simulation tools that would enable
optimal DSCM for multi region, high volume and high complexity
manufacturing environment was proposed.
Digital Article Identifier (DOI):
40
5390
Developing the Personal, Dissolving the Political
Abstract: The emergence of person-centred discourse based
around notions of 'personal development planning- and 'work'life
balance' has taken hold in education and the workplace in recent
years. This paper examines this discourse with regard to recent
developments in higher education as well as the inter-related issue of
work-life balance in occupational careers. In both cases there have
been national and trans-national policy initiatives directed towards
improving both personal opportunities and competitive advantage in
a global knowledge-based economy. However, despite an increasing
concern with looking outward at this globalised educational and
employment marketplace, there is something of a paradox in
encouraging people to look inward at themselves in order to become
more self-determined. This apparent paradox is considered from a
discourse analytic perspective in terms of the ideological effects of an
increasing concern with the personal world. Specifically, it is argued
that there are tensions that emerge from a concern with an innerdirected
process of self-reflection that dissolve any engagement with
wider political issues that impact upon educational and career
development.
Digital Article Identifier (DOI):
39
2348
Knowledge Sharing based on Semantic Nets and Mereology to Avoid Risks in Manufacturing
Abstract: The right information at the right time influences the
enterprise and technical success. Sharing knowledge among members
of a big organization may be a complex activity. And as long as the
knowledge is not shared, can not be exploited by the organization.
There are some mechanisms which can originate knowledge sharing.
It is intended, in this paper, to trigger these mechanisms by using
semantic nets. Moreover, the intersection and overlapping of terms
and sub-terms, as well as their relationships will be described through
the mereology science for the whole knowledge sharing system. It is
proposed a knowledge system to supply to operators with the right
information about a specific process and possible risks, e.g. at the
assembly process, at the right time in an automated manufacturing
environment, such as at the automotive industry.
Digital Article Identifier (DOI):
38
5358
Machine Learning Techniques for Short-Term Rain Forecasting System in the Northeastern Part of Thailand
Abstract: This paper presents the methodology from machine
learning approaches for short-term rain forecasting system. Decision
Tree, Artificial Neural Network (ANN), and Support Vector Machine
(SVM) were applied to develop classification and prediction models
for rainfall forecasts. The goals of this presentation are to
demonstrate (1) how feature selection can be used to identify the
relationships between rainfall occurrences and other weather
conditions and (2) what models can be developed and deployed for
predicting the accurate rainfall estimates to support the decisions to
launch the cloud seeding operations in the northeastern part of
Thailand. Datasets collected during 2004-2006 from the
Chalermprakiat Royal Rain Making Research Center at Hua Hin,
Prachuap Khiri khan, the Chalermprakiat Royal Rain Making
Research Center at Pimai, Nakhon Ratchasima and Thai
Meteorological Department (TMD). A total of 179 records with 57
features was merged and matched by unique date. There are three
main parts in this work. Firstly, a decision tree induction algorithm
(C4.5) was used to classify the rain status into either rain or no-rain.
The overall accuracy of classification tree achieves 94.41% with the
five-fold cross validation. The C4.5 algorithm was also used to
classify the rain amount into three classes as no-rain (0-0.1 mm.),
few-rain (0.1- 10 mm.), and moderate-rain (>10 mm.) and the overall
accuracy of classification tree achieves 62.57%. Secondly, an ANN
was applied to predict the rainfall amount and the root mean square
error (RMSE) were used to measure the training and testing errors of
the ANN. It is found that the ANN yields a lower RMSE at 0.171 for
daily rainfall estimates, when compared to next-day and next-2-day
estimation. Thirdly, the ANN and SVM techniques were also used to
classify the rain amount into three classes as no-rain, few-rain, and
moderate-rain as above. The results achieved in 68.15% and 69.10%
of overall accuracy of same-day prediction for the ANN and SVM
models, respectively. The obtained results illustrated the comparison
of the predictive power of different methods for rainfall estimation.
Digital Article Identifier (DOI):
37
757
Adaptive Transient and CW RF Interference Mitigation in HF OTH Radar: Experimental Results
Abstract: We introduce an adaptive technique for the joint mitigation of transients and continuous-wave radio-frequency co-channel interference (CW RFI) in high-frequency (HF) over-the-horizon radars (OTHRs). The performance of this technique is illustrated using data from an operational surface-wave radar (SECAR) and from recent experimental trials with sky-wave (SW) and sky-wave–line-of-sight (SKYLOS) HF OTHRs.
Digital Article Identifier (DOI):
36
1428
Fuzzy PID Controller with Coupled Rules for a Nonlinear Quarter Car Model
Abstract: In this study, Fuzzy PID Control scheme is designed
for an active suspension system. The main goal of an active
suspension system for using in a vehicle model is reducing body
deflections and handling high comfort for a passenger car. The
present system was modelled as a two-degree-of-freedom (2-DOF)
nonlinear vehicle model.
Digital Article Identifier (DOI):
35
10248
Effects of Rarefaction and Compressibility on Fluid Flow at Slip Flow Regime by Direct Simulation of Roughness
Abstract: A two dimensional numerical simulation has been
performed for incompressible and compressible fluid flow through
microchannels in slip flow regime. The Navier-Stokes equations have
been solved in conjunction with Maxwell slip conditions for
modeling flow field associated with slip flow regime. The wall
roughness is simulated with triangular microelements distributed on
wall surfaces to study the effects of roughness on fluid flow. Various
Mach and Knudsen numbers are used to investigate the effects of
rarefaction as well as compressibility. It is found that rarefaction has
more significant effect on flow field in microchannels with higher
relative roughness. It is also found that compressibility has more
significant effects on Poiseuille number when relative roughness
increases. In addition, similar to incompressible models the increase
in average fRe is more significant at low Knudsen number flows but
the increase of Poiseuille number duo to relative roughness is sharper
for compressible models. The numerical results have also validated
with some available theoretical and experimental relations and good
agreements have been seen.
Digital Article Identifier (DOI):
34
663
Simulation of Roughness Shape and Distribution Effects on Rarefied and Compressible Flows at Slip Flow Regime
Abstract: A numerical simulation of micro Poiseuille flow has
performed for rarefied and compressible flow at slip flow regimes.
The wall roughness is simulated in two cases with triangular
microelements and random micro peaks distributed on wall surfaces
to study the effects of roughness shape and distribution on flow field.
Two values of Mach and Knudsen numbers have used to investigate
the effects of rarefaction as well as compressibility. The numerical
results have also checked with available theoretical and experimental
relations and good agreements has achieved. High influence of
roughness shape can be seen for both compressible and
incompressible rarefied flows. In addition it is found that rarefaction
has more significant effect on flow field in microchannels with
higher relative roughness. It is also found that compressibility has
more significant effects on Poiseuille number when relative
roughness increases.
Digital Article Identifier (DOI):
33
11213
Effects of Nanolayer Structure and Brownian Motion of Particles in Thermal Conductivity Enhancement of Nanofluids
Abstract: Nanofluids are novel fluids that are going to have an
important role in future industrial thermal device designs. Studies are
being predominantly conducted on the mechanism of these heat
transfers. The key to this attraction is in the increase in thermal
conductivity brought about by the Nanofluids compared with the
base fluid. Different models have been proposed for calculation of
effective thermal conduction that has been gradually modified. In this
investigation effect of nanolayer structure and Brownian motion of
particles are studied and a new modified thermal conductivity model
is proposed. Temperature, concentration, nanolayer thickness and
particle size are taken as variables and their effect are studied
simultaneously on the thermal conductivity of the fluids, showing the
concentration of the nanoparticles to affect the nanolayer thickness
which also affects the Brownian motion.
Digital Article Identifier (DOI):
32
15134
A CFD Study of Sensitive Parameters Effect on the Combustion in a High Velocity Oxygen-Fuel Thermal Spray Gun
Abstract: High-velocity oxygen fuel (HVOF) thermal spraying
uses a combustion process to heat the gas flow and coating material.
A computational fluid dynamics (CFD) model has been developed to
predict gas dynamic behavior in a HVOF thermal spray gun in which
premixed oxygen and propane are burnt in a combustion chamber
linked to a parallel-sided nozzle. The CFD analysis is applied to
investigate axisymmetric, steady-state, turbulent, compressible,
chemically reacting, subsonic and supersonic flow inside and outside
the gun. The gas velocity, temperature, pressure and Mach number
distributions are presented for various locations inside and outside
the gun. The calculated results show that the most sensitive
parameters affecting the process are fuel-to-oxygen gas ratio and
total gas flow rate. Gas dynamic behavior along the centerline of the
gun depends on both total gas flow rate and fuel-to-oxygen gas ratio.
The numerical simulations show that the axial gas velocity and Mach
number distribution depend on both flow rate and ratio; the highest
velocity is achieved at the higher flow rate and most fuel-rich ratio.
In addition, the results reported in this paper illustrate that the
numerical simulation can be one of the most powerful and beneficial
tools for the HVOF system design, optimization and performance
analysis.
Digital Article Identifier (DOI):
31
594
Three Dimensional Modeling of Mixture Formation and Combustion in a Direct Injection Heavy-Duty Diesel Engine
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.
Digital Article Identifier (DOI):
30
6876
Rotor Bearing System Analysis Using the Transfer Matrix Method with Thickness Assumption of Disk and Bearing
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Digital Article Identifier (DOI):
29
4255
Development a New Model of EEVC/WG17 Lower Legform for Pedestrian Safety
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Digital Article Identifier (DOI):
28
7866
Exploiting Machine Learning Techniques for the Enhancement of Acceptance Sampling
Abstract: This paper proposes an innovative methodology for
Acceptance Sampling by Variables, which is a particular category of
Statistical Quality Control dealing with the assurance of products
quality. Our contribution lies in the exploitation of machine learning
techniques to address the complexity and remedy the drawbacks of
existing approaches. More specifically, the proposed methodology
exploits Artificial Neural Networks (ANNs) to aid decision making
about the acceptance or rejection of an inspected sample. For any
type of inspection, ANNs are trained by data from corresponding
tables of a standard-s sampling plan schemes. Once trained, ANNs
can give closed-form solutions for any acceptance quality level and
sample size, thus leading to an automation of the reading of the
sampling plan tables, without any need of compromise with the
values of the specific standard chosen each time. The proposed
methodology provides enough flexibility to quality control engineers
during the inspection of their samples, allowing the consideration of
specific needs, while it also reduces the time and the cost required for
these inspections. Its applicability and advantages are demonstrated
through two numerical examples.
Digital Article Identifier (DOI):
27
3321
Sensor Optimisation via H∞ Applied to a MAGLEV Suspension System
Abstract: In this paper a systematic method via H∞ control
design is proposed to select a sensor set that satisfies a number
of input criteria for a MAGLEV suspension system. The proposed
method recovers a number of optimised controllers for each possible
sensor set that satisfies the performance and constraint criteria using
evolutionary algorithms.
Digital Article Identifier (DOI):
26
15937
State-Space PD Feedback Control
Abstract: A challenged control problem is when the
performance is pushed to the limit. The state-derivative feedback
control strategy directly uses acceleration information for feedback
and state estimation. The derivative part is concerned with the rateof-
change of the error with time. If the measured variable approaches
the set point rapidly, then the actuator is backed off early to allow it
to coast to the required level. Derivative action makes a control
system behave much more intelligently. A sensor measures the
variable to be controlled and the measured in formation is fed back to
the controller to influence the controlled variable. A high gain
problem can be also formulated for proportional plus derivative
feedback transformation. Using MATLAB Simulink dynamic
simulation tool this paper examines a system with a proportional plus
derivative feedback and presents an automatic implementation of
finding an acceptable controlled system. Using feedback
transformations the system is transformed into another system.
Digital Article Identifier (DOI):
25
15936
Robust Stability in Multivariable Neural Network Control using Harmonic Analysis
Abstract: Robust stability and performance are the two most
basic features of feedback control systems. The harmonic balance
analysis technique enables to analyze the stability of limit cycles
arising from a neural network control based system operating over
nonlinear plants. In this work a robust stability analysis based on the
harmonic balance is presented and applied to a neural based control
of a non-linear binary distillation column with unstructured
uncertainty. We develop ways to describe uncertainty in the form of
neglected nonlinear dynamics and high harmonics for the plant and
controller respectively. Finally, conclusions about the performance of
the neural control system are discussed using the Nyquist stability
margin together with the structured singular values of the uncertainty
as a robustness measure.
Digital Article Identifier (DOI):
24
14603
Optimal Speed Controller Design of the Two-Inertia Stabilization System
Abstract: This paper focuses on systematic analysis and
controller design of the two-inertia STABILIZATION system,
considering the angular motion on a base body. This approach is
essential to the stabilization system to aim at a target under three or six
degrees of freedom base motion. Four controllers, such as
conventional PDF(Pseudo-Derivative Feedback) controller with
motor speed feedback, PDF controller with load speed feedback,
modified PDF controller with motor-load speed feedback and
feedforward controller added to modified PDF controller, are
suggested to improve reference tracking and disturbance rejection
performance. Characteristics and performance of each controller are
analyzed and validated by simulation in the case of the modified PDF
controller with and without a feedforward controller.
Digital Article Identifier (DOI):
23
15731
Fuzzy Control of Macroeconomic Models
Abstract: The optimal control is one of the possible controllers
for a dynamic system, having a linear quadratic regulator and using
the Pontryagin-s principle or the dynamic programming method .
Stochastic disturbances may affect the coefficients (multiplicative
disturbances) or the equations (additive disturbances), provided that
the shocks are not too great . Nevertheless, this approach encounters
difficulties when uncertainties are very important or when the probability
calculus is of no help with very imprecise data. The fuzzy
logic contributes to a pragmatic solution of such a problem since it
operates on fuzzy numbers. A fuzzy controller acts as an artificial
decision maker that operates in a closed-loop system in real time.
This contribution seeks to explore the tracking problem and control
of dynamic macroeconomic models using a fuzzy learning algorithm.
A two inputs - single output (TISO) fuzzy model is applied to the
linear fluctuation model of Phillips and to the nonlinear growth model
of Goodwin.
Digital Article Identifier (DOI):
22
1085
Denosing ECG using Translation Invariant Multiwavelet
Abstract: In this paper, we propose a method to reduce the
various kinds of noise while gathering and recording the
electrocardiogram (ECG) signal. Because of the defects of former
method in the noise elimination of ECG signal, we use translation
invariant (TI) multiwavelet denoising method to the noise elimination.
The advantage of the proposed method is that it may not only remain
the geometrical characteristics of the original ECG signal and keep the
amplitudes of various ECG waveforms efficiently, but also suppress
impulsive noise to some extent. The simulation results indicate that the
proposed method are better than former removing noise method in
aspects of remaining geometrical characteristics of ECG signal and the
signal-to-noise ratio (SNR).
Digital Article Identifier (DOI):
21
11061
Effect of Vibration Intervention on Leg-press Exercise
Abstract: Many studies have emphasized the importance of
resistive exercise to maintain a healthy human body, particular in
prevention of weakening of physical strength. Recently, some studies
advocated that an application of vibration as a supplementary means in
a regular training was effective in encouraging physical strength. Aim
of the current study was, therefore, to identify if an application of
vibration in a resistive exercise was effective in encouraging physical
strength as that in a regular training. A 3-dimensional virtual lower
extremity model for a healthy male and virtual leg-press model were
generated and synchronized. Dynamic leg-press exercises on a slide
machine with/without extra load and on a footboard with vibration as
well as on a slide machine with extra load were analyzed. The results
of the current indicated that the application of the vibration on the
dynamic leg-press exercise might be not greatly effective in
encouraging physical strength, compared with the dynamic leg press
exercise with extra load. It was, however, thought that the application
of the vibration might be helpful to elderly individuals because the
reduced maximum muscle strength appeared by the effect of the
vibration may avoid a muscular spasm, which can be driven from a
high muscle strength sometimes produced during the leg-press
exercise with extra load.
Digital Article Identifier (DOI):
20
2761
Impact of Reflectors on Solar Energy Systems
Abstract: The paper aims to show that implementing different
types of reflectors in solar energy systems, will dramatically improve
energy production by means of concentrating and intensifying more
sunlight onto a solar cell. The Solar Intensifier unit is designed to
increase efficiency and performance of a set of solar panels. The unit
was fabricated and tested. The experimental results show good
improvement in the performance of the solar energy system.
Digital Article Identifier (DOI):
19
3956
Switched Reluctance Generator for Wind Power Applications
Abstract: Green house effect has becomes a serious concern in
many countries due to the increase consumption of the fossil fuel.
There have been many studies to find an alternative power source.
Wind energy found to be one of the most useful solutions to help in
overcoming the air pollution and global. There is no agreed solution
to conversion of wind energy to electrical energy. In this paper, the
advantages of using a Switched Reluctance Generator (SRG) for
wind energy applications. The theoretical study of the self excitation
of a SRG and the determination of the variable parameters in a SRG
design are discussed. The design parameters for the maximum power
output of the SRG are computed using Matlab simulation. The
designs of the circuit to control the variable parameters in a SRG to
provide the maximum power output are also discussed.
Digital Article Identifier (DOI):
18
3071
A Sub-Pixel Image Registration Technique with Applications to Defect Detection
Abstract: This paper presents a useful sub-pixel image
registration method using line segments and a sub-pixel edge detector.
In this approach, straight line segments are first extracted from gray
images at the pixel level before applying the sub-pixel edge detector.
Next, all sub-pixel line edges are mapped onto the orientation-distance
parameter space to solve for line correspondence between images.
Finally, the registration parameters with sub-pixel accuracy are
analytically solved via two linear least-square problems. The present
approach can be applied to various fields where fast registration with
sub-pixel accuracy is required. To illustrate, the present approach is
applied to the inspection of printed circuits on a flat panel. Numerical
example shows that the present approach is effective and accurate
when target images contain a sufficient number of line segments,
which is true in many industrial problems.
Digital Article Identifier (DOI):
17
8132
Normalized Cumulative Spectral Distribution in Music
Abstract: As the remedy used music becomes active and
meditation effect through the music is verified, people take a growing
interest about psychological balance or remedy given by music. From
traditional studies, it is verified that the music of which spectral
envelop varies approximately as 1/f (f is frequency) down to a
frequency of low frequency bandwidth gives psychological balance.
In this paper, we researched signal properties of music which gives
psychological balance. In order to find this, we derived the property
from voice. Music composed by voice shows large value in NCSD.
We confirmed the degree of deference between music by curvature of
normalized cumulative spectral distribution. In the music that gives
psychological balance, the curvature shows high value, otherwise, the
curvature shows low value.
Digital Article Identifier (DOI):
16
7577
Fast Depth Estimation with Filters
Abstract: Fast depth estimation from binocular vision is often
desired for autonomous vehicles, but, most algorithms could not easily
be put into practice because of the much time cost. We present an
image-processing technique that can fast estimate depth image from
binocular vision images. By finding out the lines which present the
best matched area in the disparity space image, the depth can be
estimated. When detecting these lines, an edge-emphasizing filter is
used. The final depth estimation will be presented after the smooth
filter. Our method is a compromise between local methods and global
optimization.
Digital Article Identifier (DOI):
15
10139
Wavelet Based Qualitative Assessment of Femur Bone Strength Using Radiographic Imaging
Abstract: In this work, the primary compressive strength
components of human femur trabecular bone are qualitatively
assessed using image processing and wavelet analysis. The Primary
Compressive (PC) component in planar radiographic femur trabecular
images (N=50) is delineated by semi-automatic image processing
procedure. Auto threshold binarization algorithm is employed to
recognize the presence of mineralization in the digitized images. The
qualitative parameters such as apparent mineralization and total area
associated with the PC region are derived for normal and abnormal
images.The two-dimensional discrete wavelet transforms are utilized
to obtain appropriate features that quantify texture changes in medical
images .The normal and abnormal samples of the human femur are
comprehensively analyzed using Harr wavelet.The six statistical
parameters such as mean, median, mode, standard deviation, mean
absolute deviation and median absolute deviation are derived at level
4 decomposition for both approximation and horizontal wavelet
coefficients. The correlation coefficient of various wavelet derived
parameters with normal and abnormal for both approximated and
horizontal coefficients are estimated. It is seen that in almost all cases
the abnormal show higher degree of correlation than normals. Further
the parameters derived from approximation coefficient show more
correlation than those derived from the horizontal coefficients. The
parameters mean and median computed at the output of level 4 Harr
wavelet channel was found to be a useful predictor to delineate the
normal and the abnormal groups.
Digital Article Identifier (DOI):
14
1795
3D Dense Correspondence for 3D Dense Morphable Face Shape Model
Abstract: Realistic 3D face model is desired in various
applications such as face recognition, games, avatars, animations, and
etc. Construction of 3D face model is composed of 1) building a face
shape model and 2) rendering the face shape model. Thus, building a
realistic 3D face shape model is an essential step for realistic 3D face
model. Recently, 3D morphable model is successfully introduced to
deal with the various human face shapes. 3D dense correspondence
problem should be precedently resolved for constructing a realistic 3D
dense morphable face shape model. Several approaches to 3D dense
correspondence problem in 3D face modeling have been proposed
previously, and among them optical flow based algorithms and TPS
(Thin Plate Spline) based algorithms are representative. Optical flow
based algorithms require texture information of faces, which is
sensitive to variation of illumination. In TPS based algorithms
proposed so far, TPS process is performed on the 2D projection
representation in cylindrical coordinates of the 3D face data, not
directly on the 3D face data and thus errors due to distortion in data
during 2D TPS process may be inevitable.
In this paper, we propose a new 3D dense correspondence algorithm
for 3D dense morphable face shape modeling. The proposed algorithm
does not need texture information and applies TPS directly on 3D face
data. Through construction procedures, it is observed that the proposed
algorithm constructs realistic 3D face morphable model reliably and
fast.
Digital Article Identifier (DOI):
13
9608
Face Authentication for Access Control based on SVM using Class Characteristics
Abstract: Face authentication for access control is a face
membership authentication which passes the person of the incoming
face if he turns out to be one of an enrolled person based on face
recognition or rejects if not. Face membership authentication belongs
to the two class classification problem where SVM(Support Vector
Machine) has been successfully applied and shows better performance
compared to the conventional threshold-based classification. However,
most of previous SVMs have been trained using image feature vectors
extracted from face images of each class member(enrolled
class/unenrolled class) so that they are not robust to variations in
illuminations, poses, and facial expressions and much affected by
changes in member configuration of the enrolled class
In this paper, we propose an effective face membership
authentication method based on SVM using class discriminating
features which represent an incoming face image-s associability with
each class distinctively. These class discriminating features are weakly
related with image features so that they are less affected by variations
in illuminations, poses and facial expression.
Through experiments, it is shown that the proposed face
membership authentication method performs better than the threshold
rule-based or the conventional SVM-based authentication methods and
is relatively less affected by changes in member size and membership.
Digital Article Identifier (DOI):
12
14089
An Improved Quality Adaptive Rate Filtering Technique Based on the Level Crossing Sampling
Abstract: Mostly the systems are dealing with time varying
signals. The Power efficiency can be achieved by adapting the system
activity according to the input signal variations. In this context
an adaptive rate filtering technique, based on the level crossing sampling
is devised. It adapts the sampling frequency and the filter order
by following the input signal local variations. Thus, it correlates the
processing activity with the signal variations. Interpolation is required
in the proposed technique. A drastic reduction in the interpolation
error is achieved by employing the symmetry during the interpolation
process. Processing error of the proposed technique is
calculated. The computational complexity of the proposed filtering
technique is deduced and compared to the classical one. Results
promise a significant gain of the computational efficiency and hence
of the power consumption.
Digital Article Identifier (DOI):
11
9401
Segmentation of Cardiac Images by the Force Field Driven Speed Term
Abstract: The class of geometric deformable models, so-called
level sets, has brought tremendous impact to medical imagery. In
this paper we present yet another application of level sets to medical
imaging. The method we give here will in a way modify the speed
term in the standard level sets equation of motion. To do so we
build a potential based on the distance and the gradient of the
image we study. In turn the potential gives rise to the force field:
F~F(x, y) = P
∀(p,q)∈I
((x, y) - (p, q)) |ÔêçI(p,q)|
|(x,y)-(p,q)|
2 . The direction
and intensity of the force field at each point will determine the
direction of the contour-s evolution. The images we used to test
our method were produced by the Univesit'e de Sherbrooke-s PET
scanners.
Digital Article Identifier (DOI):
10
8499
Adaptive Kernel Filtering Used in Video Processing
Abstract: In this paper we present a noise reduction filter for video processing. It is based on the recently proposed two dimensional steering kernel, extended to three dimensions and further augmented to suit the spatial-temporal domain of video processing. Two alternative filters are proposed - the time symmetric kernel and the time asymmetric kernel. The first reduces the noise on single sequences, but to handle the problems at scene shift the asymmetric kernel is introduced. The performance of both are tested on simulated data and on a real video sequence together with the existing steering kernel. The proposed kernels improves the Rooted Mean Squared Error (RMSE) compared to the original steering kernel method on video material.
Digital Article Identifier (DOI):
9
10107
Analytical Camera Model Supplemented with Influence of Temperature Variations
Abstract: A camera in the building site is exposed to different
weather conditions. Differences between images of the same scene
captured with the same camera arise also due to temperature variations.
The influence of temperature changes on camera parameters
were modelled and integrated into existing analytical camera model.
Modified camera model enables quantitatively assessing the influence
of temperature variations.
Digital Article Identifier (DOI):
8
7294
Influence of Temperature Variations on Calibrated Cameras
Abstract: The camera parameters are changed due to temperature
variations, which directly influence calibrated cameras accuracy.
Robustness of calibration methods were measured and their accuracy
was tested. An error ratio due to camera parameters change
with respect to total error originated during calibration process was
determined. It pointed out that influence of temperature variations
decrease by increasing distance of observed objects from cameras.
Digital Article Identifier (DOI):
7
10083
Action Recognition in Video Sequences using a Mealy Machine
Abstract: In this paper the use of sequential machines for recognizing actions taken by the objects detected by a general tracking algorithm is proposed. The system may deal with the uncertainty inherent in medium-level vision data. For this purpose, fuzzification of input data is performed. Besides, this transformation allows to manage data independently of the tracking application selected and enables adding characteristics of the analyzed scenario. The representation of actions by means of an automaton and the generation of the input symbols for finite automaton depending on the object and action compared are described. The output of the comparison process between an object and an action is a numerical value that represents the membership of the object to the action. This value is computed depending on how similar the object and the action are. The work concludes with the application of the proposed technique to identify the behavior of vehicles in road traffic scenes.
Digital Article Identifier (DOI):
6
9067
Clustered Signatures for Modeling and Recognizing 3D Rigid Objects
Abstract: This paper describes a probabilistic method for
three-dimensional object recognition using a shared pool of surface
signatures. This technique uses flatness, orientation, and convexity
signatures that encode the surface of a free-form object into three
discriminative vectors, and then creates a shared pool of data by
clustering the signatures using a distance function. This method
applies the Bayes-s rule for recognition process, and it is extensible
to a large collection of three-dimensional objects.
Digital Article Identifier (DOI):
5
14908
Exact Image Super-Resolution for Pure Translational Motion and Shift-Invariant Blur
Abstract: In this work, a special case of the image superresolution
problem where the only type of motion is global
translational motion and the blurs are shift-invariant is investigated.
The necessary conditions for exact reconstruction of the original
image by using finite impulse-response reconstruction filters are
developed. Given that the conditions are satisfied, a method for exact
super-resolution is presented and some simulation results are shown.
Digital Article Identifier (DOI):
4
11297
Multiscale Blind Image Restoration with a New Method
Abstract: A new method, based on the normal shrink and
modified version of Katssagelous and Lay, is proposed for multiscale
blind image restoration. The method deals with the noise and blur in
the images. It is shown that the normal shrink gives the highest S/N
(signal to noise ratio) for image denoising process. The multiscale
blind image restoration is divided in two sections. The first part of
this paper proposes normal shrink for image denoising and the
second part of paper proposes modified version of katssagelous and
Lay for blur estimation and the combination of both methods to reach
a multiscale blind image restoration.
Digital Article Identifier (DOI):
3
13665
An Automatic Gridding and Contour Based Segmentation Approach Applied to DNA Microarray Image Analysis
Abstract: DNA microarray technology is widely used by
geneticists to diagnose or treat diseases through gene expression.
This technology is based on the hybridization of a tissue-s DNA
sequence into a substrate and the further analysis of the image
formed by the thousands of genes in the DNA as green, red or yellow
spots. The process of DNA microarray image analysis involves
finding the location of the spots and the quantification of the
expression level of these. In this paper, a tool to perform DNA
microarray image analysis is presented, including a spot addressing
method based on the image projections, the spot segmentation
through contour based segmentation and the extraction of relevant
information due to gene expression.
Digital Article Identifier (DOI):
2
13908
A New Face Recognition Method using PCA, LDA and Neural Network
Abstract: In this paper, a new face recognition method based on
PCA (principal Component Analysis), LDA (Linear Discriminant
Analysis) and neural networks is proposed. This method consists of
four steps: i) Preprocessing, ii) Dimension reduction using PCA, iii)
feature extraction using LDA and iv) classification using neural
network. Combination of PCA and LDA is used for improving the
capability of LDA when a few samples of images are available and
neural classifier is used to reduce number misclassification caused by
not-linearly separable classes. The proposed method was tested on
Yale face database. Experimental results on this database
demonstrated the effectiveness of the proposed method for face
recognition with less misclassification in comparison with previous
methods.
Digital Article Identifier (DOI):
1
4014
Adaptive Gaussian Mixture Model for Skin Color Segmentation
Abstract: Skin color based tracking techniques often assume a
static skin color model obtained either from an offline set of library
images or the first few frames of a video stream. These models
can show a weak performance in presence of changing lighting or
imaging conditions. We propose an adaptive skin color model based
on the Gaussian mixture model to handle the changing conditions.
Initial estimation of the number and weights of skin color clusters
are obtained using a modified form of the general Expectation
maximization algorithm, The model adapts to changes in imaging
conditions and refines the model parameters dynamically using spatial
and temporal constraints. Experimental results show that the method
can be used in effectively tracking of hand and face regions.
Digital Article Identifier (DOI):