193
8909
Solution of Density Dependent Nonlinear Reaction-Diffusion Equation Using Differential Quadrature Method
Abstract: In this study, the density dependent nonlinear reactiondiffusion
equation, which arises in the insect dispersal models, is
solved using the combined application of differential quadrature
method(DQM) and implicit Euler method. The polynomial based
DQM is used to discretize the spatial derivatives of the problem. The
resulting time-dependent nonlinear system of ordinary differential
equations(ODE-s) is solved by using implicit Euler method. The
computations are carried out for a Cauchy problem defined by a onedimensional
density dependent nonlinear reaction-diffusion equation
which has an exact solution. The DQM solution is found to be in a
very good agreement with the exact solution in terms of maximum
absolute error. The DQM solution exhibits superior accuracy at large
time levels tending to steady-state. Furthermore, using an implicit
method in the solution procedure leads to stable solutions and larger
time steps could be used.
Digital Article Identifier (DOI):
192
1108
Pyrolysis Characteristics and Kinetics of Macroalgae Biomass Using Thermogravimetric Analyzer
Abstract: The pyrolysis characteristics and kinetics of seven marine biomass, which are fixed Enteromorpha clathrata, floating Enteromorpha clathrata, Ulva lactuca L., Zosterae Marinae L., Thallus Laminariae, Asparagus schoberioides kunth and Undaria pinnatifida (Harv.), were studied with thermogravimetric analysis method. Simultaneously, cornstalk, which is a grass biomass, and sawdust, which is a lignocellulosic biomass, were references. The basic pyrolysis characteristics were studied by using TG- DTG-DTA curves. The results showed that there were three stages (dehydration, dramatic weight loss and slow weight loss) during the whole pyrolysis process of samples. The Tmax of marine biomass was significantly lower than two kinds of terrestrial biomass. Zosterae Marinae L. had a relatively high stability of pyrolysis, but floating Enteromorpha clathrata had lowest stability of pyrolysis and a good combustion characteristics. The corresponding activation energy E and frequency factor A were obtained by Coats-Redfern method. It was found that the pyrolysis reaction mechanism functions of three kinds of biomass are different.
Digital Article Identifier (DOI):
191
4588
Anodic Growth of Highly Ordered Titanium Oxide Nanotube Arrays: Effects of Critical Anodization Factors on their Photocatalytic Activity
Abstract: Highly ordered arrays of TiO2 nanotubes (TiNTs) were grown vertically on Ti foil by electrochemical anodization. We controlled the lengths of these TiNTs from 2.4 to 26.8 ¶üÇóμm while varying the water contents (1, 3, and 6 wt%) of the electrolyte in ethylene glycol in the presence of 0.5 wt% NH4F with anodization for various applied voltages (20–80 V), periods (10–240 min) and temperatures (10–30 oC). For vertically aligned TiNT arrays, not only the increase in their tube lengths, but also their geometric (wall thickness and surface roughness) and crystalline structure lead to a significant influence on photocatalytic activity. The length optimization for methylene blue (MB) photodegradation was 18 μm. Further extending the TiNT length yielded lower photocatalytic activity presumably related to the limited MB diffusion and light-penetration depth into the TiNT arrays. The results indicated that a maximum MB photodegradation rate was obtained for the discrete anatase TiO2 nanotubes with thick and rough walls.
Digital Article Identifier (DOI):
190
13286
Response Quality Evaluation in Heterogeneous Question Answering System: A Black-box Approach
Abstract: The evaluation of the question answering system is a major research area that needs much attention. Before the rise of domain-oriented question answering systems based on natural language understanding and reasoning, evaluation is never a problem as information retrieval-based metrics are readily available for use. However, when question answering systems began to be more domains specific, evaluation becomes a real issue. This is especially true when understanding and reasoning is required to cater for a wider variety of questions and at the same time achieve higher quality responses The research in this paper discusses the inappropriateness of the existing measure for response quality evaluation and in a later part, the call for new standard measures and the related considerations are brought forward. As a short-term solution for evaluating response quality of heterogeneous systems, and to demonstrate the challenges in evaluating systems of different nature, this research presents a black-box approach using observation, classification scheme and a scoring mechanism to assess and rank three example systems (i.e. AnswerBus, START and NaLURI).
Digital Article Identifier (DOI):
189
1100
Reproduction Performance of Etawah Cross Bred Goats in Estrus Synchronization by Controlled Internal Drug Release Implant and Pgf2α Continued by Artificial Insemination
Abstract: The estrus female Etawah cross bred goats were
synchronized estrus by controlled internal drug release (CIDR)
implants for 10 days combined with PGF2α injection, and continued
by artificial insemination (AI) within the hours of 24 period. Vaginal
epithelium was taken to determine estrus cycle of the goats without
estrus synchronization. The estrus responds (the puffy of vulva and
vaginal pH) and percentage of pregnancy were investigated. The data
were analyzed descriptively and Independent Sample T-Test. The
results showed that the puffy of vulva and vaginal pH were
significantly different in synchronized estrus goats and control goats
(2.18 ± 0.33 cm vs. 1.20 ± 0.16 cm and 8.55 ± 0.63 vs. 8.22 ± 0.22).
Percentage of pregnancy was higher in synchronized estrus goats
(73.33%) than in control (53.3%). Estrus synchronization by using
CIDR implants and PGF2, continued by AI was effective to improve
reproduction performance of Etawah cross bred goats.
Digital Article Identifier (DOI):
188
6767
Process Optimization for Enhanced Production of Cell Biomass and Metabolites of Fluorescent Pseudomonad R81
Abstract: The fluorescent pseudomonad strain R81 is a root
colonizing rhizobacteria which promotes the growth of many plants
by various mechanisms. Its broth containing siderophore (ironchelating
compound) and 2,4- diacetyl phloroglucinol (DAPG) is
used for preparing bioinoculant formulations for agronomical
applications. Glycerol was found to be the best carbon source for
improved biomass production. Splitting of nitrogen source to NH4Cl
and urea had a stabilizing effect on pH during batch cultivation. Ltryptophan
at 0.5 % in the medium increased the siderophore
production to 850 mg/l. During batch cultivation of the strain in a
bioreactor, a maximum of 4 g/l of dry cell mass, 1.8 g/l of
siderophore and 20 mg/l of DAPG was achieved when glycerol was
15 g/l and C/N ratio was maintained at 12.5. In case of intermittent
feeding of fresh medium during fed-batch cultivation, the dry cell
mass was increased to 25 g/l with improved production of DAPG to
70 mg/l.
Digital Article Identifier (DOI):
187
12410
Species Spreading due to Environmental Hostility, Dispersal Adaptation and Allee Effects
Abstract: A phenomenological model for species spreading which incorporates the Allee effect, a species- maximum attainable growth rate, collective dispersal rate and dispersal adaptability is presented. This builds on a well-established reaction-diffusion model for spatial spreading of invading organisms. The model is phrased in terms of the “hostility" (which quantifies the Allee threshold in relation to environmental sustainability) and dispersal adaptability (which measures how a species is able to adapt its migratory response to environmental conditions). The species- invading/retreating speed and the sharpness of the invading boundary are explicitly characterised in terms of the fundamental parameters, and analysed in detail.
Digital Article Identifier (DOI):
186
12996
Ecolabeling and Green Certification for Effective Fisheries Management – An Analysis
Abstract: Nowadays there is a growing environmental concern
and the business communities have slowly started recognising
environmental protection and sustainable utilization of natural
resources into their marketing strategies. This paper discusses the
various Ecolabeling and Certification Systems developed world
over to regulate and introduce Fair Trade in Ornamental Fish
Industry. Ecolabeling and green certification are considered as part
of these strategies implemented partly out of compulsion from the
National and International Regulatory Bodies and Environmental
Movements. All the major markets of ornamental fishes like
European Union, USA and Japan have started putting restrictions on
the trade to impose ecolabeling as a non tariff barrier like the one
imposed on seafood and aqua cultured products. A review was done
on the available Ecolabeling and Green Certification Schemes
available at local, national and international levels for fisheries
including aquaculture and ornamental fish trade and to examine the
success and constraints faced by these schemes during its
implementation. The primary downside of certification is the
multiplicity of ecolabels and cost incurred by applicants for
certification, costs which may in turn be passed on to consumers.
The studies reveal serious inadequacies in a number of ecolabels
and cast doubt on their overall contribution to effective fisheries
management and sustainability. The paper also discusses the
inititive taken in India to develop guidelines for Green Certification
of Fresh water ornamental fishes.
Digital Article Identifier (DOI):
185
8792
Novel Anti-leukemia Calanone Compounds by Quantitative Structure-Activity Relationship AM1 Semiempirical Method
Abstract: Quantitative Structure-Activity Relationship (QSAR)
approach for discovering novel more active Calanone derivative as
anti-leukemia compound has been conducted. There are 6
experimental activities of Calanone compounds against leukemia cell
L1210 that are used as material of the research. Calculation of
theoretical predictors (independent variables) was performed by
AM1 semiempirical method. The QSAR equation is determined by
Principle Component Regression (PCR) analysis, with Log IC50 as
dependent variable and the independent variables are atomic net
charges, dipole moment (μ), and coefficient partition of noctanol/
water (Log P). Three novel Calanone derivatives that
obtained by this research have higher activity against leukemia cell
L1210 than pure Calanone.
Digital Article Identifier (DOI):
184
6300
Visual Hull with Imprecise Input
Abstract: Imprecision is a long-standing problem in CAD design
and high accuracy image-based reconstruction applications. The visual
hull which is the closed silhouette equivalent shape of the objects
of interest is an important concept in image-based reconstruction.
We extend the domain-theoretic framework, which is a robust and
imprecision capturing geometric model, to analyze the imprecision in
the output shape when the input vertices are given with imprecision.
Under this framework, we show an efficient algorithm to generate the
2D partial visual hull which represents the exact information of the
visual hull with only basic imprecision assumptions. We also show
how the visual hull from polyhedra problem can be efficiently solved
in the context of imprecise input.
Digital Article Identifier (DOI):
183
6814
On Minimum Cycle Bases of the Wreath Product of Wheels with Stars
Abstract: The length of a cycle basis of a graph is the sum of the lengths of its elements. A minimum cycle basis is a cycle basis with minimum length. In this work, a construction of a minimum cycle basis for the wreath product of wheels with stars is presented. Moreover, the length of minimum cycle basis and the length of its longest cycle are calculated.
Digital Article Identifier (DOI):
182
8262
Multi-labeled Data Expressed by a Set of Labels
Abstract: Collected data must be organized to be utilized efficiently, and hierarchical classification of data is efficient approach to organize data. When data is classified to multiple categories or annotated with a set of labels, users request multi-labeled data by giving a set of labels. There are several interpretations of the data expressed by a set of labels. This paper discusses which data is expressed by a set of labels by introducing orders for sets of labels and shows that there are four types of orders, which are characterized by whether the labels of expressed data includes every label of the given set of labels within the range of the set. Desirable properties of the orders, data is also expressed by the higher set of labels and different sets of labels express different data, are discussed for the orders.
Digital Article Identifier (DOI):
181
7200
Depressing Turbine-Generator Supersynchronous Torsional Torques by Using Virtual Inertia
Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.
Digital Article Identifier (DOI):
180
4989
ISTER (Immune System - Tumor Efficiency Rate): An Important Key for Planning in Radiotherapic Facilities
Abstract: The use of the oncologic index ISTER allows for a more effective planning of the radiotherapic facilities in the hospitals. Any change in the radiotherapy treatment, due to unexpected stops, may be adapted by recalculating the doses to the new treatment duration while keeping the optimal prognosis. The results obtained in a simulation model on millions of patients allow the definition of optimal success probability algorithms.
Digital Article Identifier (DOI):
179
10386
Staling and Quality of Iranian Flat Bread Stored at Modified Atmosphere in Different Packaging
Abstract: This study investigated the use of modified
atmosphere packaging (MAP) and different packaging to extend the
shelf life of Barbari flat bread. Three atmospheres including 70%CO2
and 30%N2, 50% CO2 and 50%N2 and a normal air as control were
used. The bread samples were packaged in three type pouches. The
shelf life was determined by appearance of mold and yeast (M +Y) in
Barbari bread samples stored at 25 ± 1°C and 38 ± 2% relative
humidity. The results showed that it is possible to prolong the shelf
life of Barbari bread from four days to about 21 days by using
modified atmosphere packaging with high carbon dioxide
concentration and high-barrier laminated and vacuum bags packages.
However, the hardness of samples kept in MAP increase significantly
by increase of carbon dioxide concentration. The correlation
coefficient (r) between headspace CO2 concentration and hardness
was 0.997, 0.997 and 0.599 for A, B and C packaging respectively.
High negative correlation coefficients were found between the crumb
moisture and the hardness values in various packaging. There were
significant negative correlation coefficients between sensory
parameters and hardness of texture.
Digital Article Identifier (DOI):
178
1420
A Simple Constellation Precoding Technique over MIMO-OFDM Systems
Abstract: This paper studies the design of a simple constellation
precoding for a multiple-input multiple-output orthogonal frequency
division multiplexing (MIMO-OFDM) system over Rayleigh fading
channels where OFDM is used to keep the diversity replicas orthogonal
and reduce ISI effects. A multi-user environment with K synchronous
co-channel users is considered. The proposed scheme provides
a bandwidth efficient transmission for individual users by increasing
the system throughput. In comparison with the existing coded
MIMO-OFDM schemes, the precoding technique is designed under
the consideration of its low implementation complexity while providing
a comparable error performance to the existing schemes.
Analytic and simulation results have been presented to show the distinguished
error performance.
Digital Article Identifier (DOI):
177
3244
Insights into Smoothies with High Levels of Fibre and Polyphenols: Factors Influencing Chemical, Rheological and Sensory Properties
Abstract: Attempts to add fibre and polyphenols (PPs) into
popular beverages present challenges related to the properties of
finished products such as smoothies. Consumer acceptability,
viscosity and phenolic composition of smoothies containing high
levels of fruit fibre (2.5-7.5 g per 300 mL serve) and PPs (250-750
mg per 300 mL serve) were examined. The changes in total
extractable PP, vitamin C content, and colour of selected smoothies
over a storage stability trial (4°C, 14 days) were compared. A set of
acidic aqueous model beverages were prepared to further examine
the effect of two different heat treatments on the stability and
extractability of PPs. Results show that overall consumer
acceptability of high fibre and PP smoothies was low, with average
hedonic scores ranging from 3.9 to 6.4 (on a 1-9 scale). Flavour,
texture and overall acceptability decreased as fibre and polyphenol
contents increased, with fibre content exerting a stronger effect.
Higher fibre content resulted in greater viscosity, with an elevated PP
content increasing viscosity only slightly. The presence of fibre also
aided the stability and extractability of PPs after heating. A reduction
of extractable PPs, vitamin C content and colour intensity of
smoothies was observed after a 14-day storage period at 4°C. Two
heat treatments (75°C for 45 min or 85°C for 1 min) that are
normally used for beverage production, did not cause significant
reduction of total extracted PPs. It is clear that high levels of added
fibre and PPs greatly influence the consumer appeal of smoothies,
suggesting the need to develop novel formulation and processing
methods if a satisfactory functional beverage is to be developed
incorporating these ingredients.
Digital Article Identifier (DOI):
176
3832
From Micro to Nanosystems: An Exploratory Study of Influences on Innovation Teams
Abstract: What influences microsystems (MEMS) and nanosystems (NEMS) innovation teams apart from technology complexity? Based on in-depth interviews with innovators, this research explores the key influences on innovation teams in the early phases of MEMS/NEMS. Projects are rare and may last from 5 to 10 years or more from idea to concept. As fundamental technology development in MEMS/NEMS is highly complex and interdisciplinary by involving expertise from different basic and engineering disciplines, R&D is rather a 'testing of ideas' with many uncertainties than a clearly structured process. The purpose of this study is to explore the innovation teams- environment and give specific insights for future management practices. The findings are grouped into three major areas: people, know-how and experience, and market. The results highlight the importance and differences of innovation teams- composition, transdisciplinary knowledge, project evaluation and management compared to the counterparts from new product development teams.
Digital Article Identifier (DOI):
175
8290
Development of Fen4/C And Fen2/C Catalysts for Hydrodesulfurization and Hydrodearomitization of Model Compounds of Heavy Oil
Abstract: Two novel hydrodesulfurization (HDS) catalysts:
FeN4/C and FeN2/C, were prepared using an impregnation-pyrolysis
method. The two materials were investigated as catalysts for
hydrodesulfurization (HDS) and hydrodearomitization (HDA) of
model compounds. The turnover frequency of the two FeN catalysts
is comparable to (FeN4/C) or even higher (FeN2/C) than that of
MoNi/Al2O3. The FeN4/C catalyst also exhibited catalytic activity
toward HDA.
Digital Article Identifier (DOI):
174
5956
Finite Element Investigation of Transmission Conditions for Non-Monotonic Temperature Interphases
Abstract: Imperfect transmission conditions modeling a thin reactive 2D interphases layer between two dissimilar bonded strips have been extracted. In this paper, the soundness of these transmission conditions for heat conduction problems are examined by the finite element method for a strong temperature-dependent source or sink and non-monotonic temperature distributions around the faces..
Digital Article Identifier (DOI):
173
5298
Design and Implementation of Project Time Management Risk Assessment Tool for SME Projects using Oracle Application Express
Abstract: Risk Assessment Tool (RAT) is an expert system that
assesses, monitors, and gives preliminary treatments automatically
based on the project plan. In this paper, a review was taken out for
the current project time management risk assessment tools for SME
software development projects, analyze risk assessment parameters,
conditions, scenarios, and finally propose risk assessment tool (RAT)
model to assess, treat, and monitor risks. An implementation prototype
system is developed to validate the model.
Digital Article Identifier (DOI):
172
12543
Web-GIS based Outdoor Education Program for Elementary Schools
Abstract: This study, focusing on the importance of encouraging
outdoor activities for children, aims to propose and implement a
Web-GIS based outdoor education program for elementary schools,
which will then be evaluated by users. Specifically, for the purpose of
improved outdoor activities in the elementary school education, the
outdoor education program, with chiefly using the Web-GIS that
provides a good information provision and sharing tool, is proposed
and implemented before being evaluated by users. Conclusions of the
study boil down to:
(1) An eight-staged outdoor education program based on the Web-GIS
was proposed for a “second school" of an elementary school that
was then implemented before being evaluated by users (teachers,
instructors, students, and their parents).
(2) The program generally received a good evaluation, while a lot of
students and their parents evaluated negatively for the degree of
discovery and for the degree of interest, respectively, in the
questionnaire survey of students and their parents conducted after
the “second school". The surveys clearly show that an issue to be
solved, from the viewpoint of teachers in particular, is the
establishment of the GIS that will easily represent teaching materials
developed by teachers and of Web-GIS, and improved significance
of the use of GIS and Web-GIS for their widespread.
Digital Article Identifier (DOI):
171
9292
The Relationship between Sheep Management and Lamb Mortality
Abstract: This study was carried out to investigate lamb mortalities relating to ewes' breed and some managemental factors on 250 pregnant ewes (190-Rahmani, 30-Ossimi and 30-Romanov) at Mehallet Mousa, Animal Production Research Station, Kafr El- Sheikh Province, Egypt. These animals divided into five groups according to the managemental factors used. The results revealed that the lamb mortality was higher in Ossimi breed and lower in Romanov one. In addition, the highest lamb mortality occurred among lambs for unsupplemented ewes, for those had body condition score two and for lambs which born outdoor. Moreover, the lamb survivability was increased by the parity of ewes. From this study it can be concluded that the lamb mortality depends on ewes' body condition score, parity, lambing system (indoor or outdoor), nutrition during pregnancy period and selected breed. In addition, the most important period for lamb survival is the first week of age.
Digital Article Identifier (DOI):
170
4127
Impact of Shearing Date on Behaviors and Performances of Pregnant Rahmani Ewes
Abstract: The effect of shearing date on behaviors and performances of 20 pregnant Rahmani ewes was evaluated in four groups (5each). Ewes were shorn at 70, 100 and 130 days of pregnancy in the first three groups respectively, while the fourth group was maintained unshorn as a control. Some behavioral and physiological data related to ewes in addition, blood cortisol level were recorded. Results revealed a significant increase in the frequencies of comfort and eating behaviors, respiratory rate, pulse rate, lamb birth weight and blood cortisol level in early and mid pregnancy shorn ewes. Also, a slight increase in pregnancy period was observed for those ewes. On the other hand, social behaviors, and core temperature were not affected by shearing. These results conclude that prenatal shearing (early and mid-pregnancy) of ewes increases the frequencies of comfort and eating behaviors, and improves the survival rates of lambs by increasing their birth weights.
Digital Article Identifier (DOI):
169
961
Barriers of Productivity in Public Sector Automotive Manufacturing Industry of Pakistan
Abstract: The public sector losses are the major cause of stagnant growth of Pakistan. Public sector automotive manufacturing industry is one of the major contributors of these losses. This research has been carried out in order to identify the major barriers of productivity of this industry and suggest measures for improvement. This qualitative and quantitative research consisted of informal interviews, discussions augmented by closed ended questionnaire. Three major manufacturing units were chosen for this research and responses from 103 employees were collected. It was found out in this research that numerous productivity flaws exist in the system which requires immediate attention. Besides highlighting flaws this research also suggests corrective actions and areas for future research to overcome these problems.
Digital Article Identifier (DOI):
168
10454
An Algorithm of Ordered Schur Factorization For Real Nonsymmetric Matrix
Abstract: In this paper, we present an algorithm for computing a
Schur factorization of a real nonsymmetric matrix with ordered diagonal
blocks such that upper left blocks contains the largest magnitude
eigenvalues. Especially in case of multiple eigenvalues, when matrix
is non diagonalizable, we construct an invariant subspaces with few
additional tricks which are heuristic and numerical results shows the
stability and accuracy of the algorithm.
Digital Article Identifier (DOI):
167
512
Evolutionary of Prostate Cancer Stem Cells in Prostate Duct
Abstract: A systems approach model for prostate cancer in prostate duct, as a sub-system of the organism is developed. It is accomplished in two steps. First this research work starts with a nonlinear system of coupled Fokker-Plank equations which models continuous process of the system like motion of cells. Then extended to PDEs that include discontinuous processes like cell mutations, proliferation and deaths. The discontinuous processes is modeled by using intensity poisson processes. The model incorporates the features of the prostate duct. The system of PDEs spatial coordinate is along the proximal distal axis. Its parameters depend on features of the prostate duct. The movement of cells is biased towards distal region and mutations of prostate cancer cells is localized in the proximal region. Numerical solutions of the full system of equations are provided, and are exhibit traveling wave fronts phenomena. This motivates the use of the standard transformation to derive a canonically related system of ODEs for traveling wave solutions. The results obtained show persistence of prostate cancer by showing that the non-negative cone for the traveling wave system is time invariant. The traveling waves have a unique global attractor is proved also. Biologically, the global attractor verifies that evolution of prostate cancer stem cells exhibit the avascular tumor growth. These numerical solutions show that altering prostate stem cell movement or mutation of prostate cancer cells lead to avascular tumor. Conclusion with comments on clinical implications of the model is discussed.
Digital Article Identifier (DOI):
166
10977
Production of Hydrogen and Carbon Nanofiber via Methane Decomposition
Abstract: High purity hydrogen and the valuable by-product of carbon nanotubes (CNTs) can be produced by the methane catalytic decomposition. The methane conversion and the performance of CNTs were determined by the choices of catalysts and the condition of decomposition reaction. In this paper, Ni/MgO and Ni/O-D (oxidized diamond) catalysts were prepared by wetness impregnation method. The effects of reaction temperature and space velocity of methane on the methane conversion were investigated in a fixed-bed. The surface area, structure and micrography were characterized with BET, XPS, SEM, EDS technology. The results showed that the conversion of methane was above 8% within 150 min (T=500) for 33Ni/O-D catalyst and higher than 25% within 120 min (T=650) for 41Ni/MgO catalyst. The initial conversion increased with the increasing temperature of the decomposition reaction, but their catalytic activities decreased rapidly while at too higher temperature. To decrease the space velocity of methane was propitious to promote the methane conversion, but not favor of the hydrogen yields. The appearance of carbon resulted from the methane decomposition lied on the support type and the condition of catalytic reaction. It presented as fiber shape on the surface of Ni/O-D at the relatively lower temperature such as 500 and 550, but as grain shape stacked on and overlayed on the surface of the metal nickel while at 650. The carbon fiber can form on the Ni/MgO surface at 650 and the diameter of the carbon fiber increased with the decreasing space velocity.
Digital Article Identifier (DOI):
165
4648
Signal-to-Noise Ratio Improvement of EMCCD Cameras
Abstract: Over the past years, the EMCCD has had a profound
influence on photon starved imaging applications relying on its unique
multiplication register based on the impact ionization effect in the
silicon. High signal-to-noise ratio (SNR) means high image quality.
Thus, SNR improvement is important for the EMCCD. This work
analyzes the SNR performance of an EMCCD with gain off and on. In
each mode, simplified SNR models are established for different
integration times. The SNR curves are divided into readout noise (or
CIC) region and shot noise region by integration time. Theoretical
SNR values comparing long frame integration and frame adding in
each region are presented and discussed to figure out which method is
more effective. In order to further improve the SNR performance,
pixel binning is introduced into the EMCCD. The results show that
pixel binning does obviously improve the SNR performance, but at the
expensive of the spatial resolution.
Digital Article Identifier (DOI):
164
7061
Mobile Qibla and Prayer Time Finder using PDA and External Digital Compass
Abstract: These days people love to travel around the world.
Regardless of their location and time, they especially Muslims still
need to perform their prayers. Normally for travelers, they need to
bring maps, compass and for Muslim, they even have to bring Qibla
pointer when they travel. It is slightly difficult to determine the Qibla
direction and to know the time for each prayer. As the technology
grows, many PDA equip with maps and GPS to locate their location.
In this paper we present a new electronic device called Mobile Qibla
and Prayer Time Finder to locate the Qibla direction and to
determine each prayer time based on the current user-s location using
PDA. This device use PIC microcontroller equipped with digital
compass where it will communicate with PDA using Bluetooth
technology and display the exact Qibla direction and prayer time
automatically at any place in the world. This device is reliable and
accurate in determining the Qibla direction and prayer time.
Digital Article Identifier (DOI):
163
2612
Combining Gene and Chemo Therapy using Multifunctional Polymeric Micelles
Abstract: Non-viral gene carriers composed of biodegradable
polymers or lipids have been considered as a safer alternative for gene
carriers over viral vectors. We have developed multi-functional
nano-micelles for both drug and gene delivery application.
Polyethyleneimine (PEI) was modified by grafting stearic acid (SA)
and formulated to polymeric micelles (PEI-SA) with positive surface
charge for gene and drug delivery. Our results showed that PEI-SA
micelles provided high siRNA binding efficiency. In addition, siRNA
delivered by PEI-SA carriers also demonstrated significantly high
cellular uptake even in the presence of serum proteins. The
post-transcriptional gene silencing efficiency was greatly improved by
the polyplex formulated by 10k PEI-SA/siRNA. The amphiphilic
structure of PEI-SA micelles provided advantages for multifunctional
tasks; where the hydrophilic shell modified with cationic charges can
electrostatically interact with DNA or siRNA, and the hydrophobic
core can serve as payloads for hydrophobic drugs, making it a
promising multifunctional vehicle for both genetic and chemotherapy
application.
Digital Article Identifier (DOI):
162
591
An Analytical Framework for Multi-Site Supply Chain Planning Problems
Abstract: As the gradual increase of the enterprise scale, the
firms may possess many manufacturing plants located in different
places geographically. This change will result in the multi-site
production planning problems under the environment of multiple
plants or production resources. Our research proposes the structural
framework to analyze the multi-site planning problems. The analytical
framework is composed of six elements: multi-site conceptual model,
product structure (bill of manufacturing), production strategy,
manufacturing capability and characteristics, production planning
constraints, and key performance indicators. As well as the discussion
of these six ingredients, we also review related literatures in this paper
to match our analytical framework. Finally we take a real-world
practical example of a TFT-LCD manufacturer in Taiwan to explain
our proposed analytical framework for the multi-site production
planning problems.
Digital Article Identifier (DOI):
161
15422
A Grey-Fuzzy Controller for Optimization Technique in Wireless Networks
Abstract: In wireless and mobile communications, this progress
provides opportunities for introducing new standards and improving
existing services. Supporting multimedia traffic with wireless networks
quality of service (QoS). In this paper, a grey-fuzzy controller for radio
resource management (GF-RRM) is presented to maximize the number
of the served calls and QoS provision in wireless networks. In a
wireless network, the call arrival rate, the call duration and the
communication overhead between the base stations and the control
center are vague and uncertain. In this paper, we develop a method to
predict the cell load and to solve the RRM problem based on the
GF-RRM, and support the present facility has been built on the
application-level of the wireless networks. The GF-RRM exhibits the
better adaptability, fault-tolerant capability and performance than other
algorithms. Through simulations, we evaluate the blocking rate, update
overhead, and channel acquisition delay time of the proposed method.
The results demonstrate our algorithm has the lower blocking rate, less
updated overhead, and shorter channel acquisition delay.
Digital Article Identifier (DOI):
160
11703
A Frequency Dependence of the Phase Field Model in Laminar Boundary Layer with Periodic Perturbations
Abstract: The frequency dependence of the phase field
model(PFM) is studied. A simple PFM is proposed, and is tested in a
laminar boundary layer. The Blasius-s laminar boundary layer
solution on a flat plate is used for the flow pattern, and several
frequencies are imposed on the PFM, and the decay times of the
interfaces are obtained. The computations were conducted for three
cases: 1) no-flow, and 2) a half ball on the laminar boundary layer, 3) a
line of mass sources in the laminar boundary layer. The computations
show the decay time becomes shorter as the frequency goes larger, and
also show that it is sensitive to both background disturbances and
surface tension parameters. It is concluded that the proposed simple
PFM can describe the properties of decay process, and could give the
fundamentals for the decay of the interface in turbulent flows.
Digital Article Identifier (DOI):
159
7133
A Study and Implementation of On-line Learning Diagnosis and Inquiry System
Abstract: In Knowledge Structure Graph, each course unit
represents a phase of learning activities. Both learning portfolios and
Knowledge Structure Graphs contain learning information of students
and let teachers know which content are difficulties and fails. The
study purposes "Dual Mode On-line Learning Diagnosis System" that
integrates two search methods: learning portfolio and knowledge
structure. Teachers can operate the proposed system and obtain the
information of specific students without any computer science
background. The teachers can find out failed students in advance and
provide remedial learning resources.
Digital Article Identifier (DOI):
158
11106
Development of Web-based Teams Management System in Construction
Abstract: Construction project control attempts to obtain real-time information and effectively enhance dynamic control and management via information sharing and analysis among project participants to eliminate construction conflicts and project delays. However, survey results for Taiwan indicate that construction commercial project management software is not widely accepted for subcontractors and suppliers. To solve the project communications problems among participants, this study presents a novel system called the Construction Dynamic Teams Communication Management (Con-DTCM) system for small-to-medium sized subcontractors and suppliers in Taiwanese Construction industry, and demonstrates that the Con-DTCM system responds to the most recent project information efficiently and enhances management of project teams (general contractor, suppliers and subcontractors) through web-based environment. Web-based technology effectively enhances information sharing during construction project management, and generates cost savings via the Internet. The main unique characteristic of the proposed Con-DTCM system is extremely user friendly and easily design compared with current commercial project management applications. The Con-DTCM system is applied to a case study of construction of a building project in Taiwan to confirm the proposed methodology and demonstrate the effectiveness of information sharing during the construction phase. The advantages of the Con-DTCM system are in improving project control and management efficiency for general contractors, and in providing dynamic project tracking and management, which enables subcontractors and suppliers to acquire the most recent project-related information. Furthermore, this study presents and implements a generic system architecture.
Digital Article Identifier (DOI):
157
7708
TOSOM: A Topic-Oriented Self-Organizing Map for Text Organization
Abstract: The self-organizing map (SOM) model is a well-known neural network model with wide spread of applications. The main characteristics of SOM are two-fold, namely dimension reduction and topology preservation. Using SOM, a high-dimensional data space will be mapped to some low-dimensional space. Meanwhile, the topological relations among data will be preserved. With such characteristics, the SOM was usually applied on data clustering and visualization tasks. However, the SOM has main disadvantage of the need to know the number and structure of neurons prior to training, which are difficult to be determined. Several schemes have been proposed to tackle such deficiency. Examples are growing/expandable SOM, hierarchical SOM, and growing hierarchical SOM. These schemes could dynamically expand the map, even generate hierarchical maps, during training. Encouraging results were reported. Basically, these schemes adapt the size and structure of the map according to the distribution of training data. That is, they are data-driven or dataoriented SOM schemes. In this work, a topic-oriented SOM scheme which is suitable for document clustering and organization will be developed. The proposed SOM will automatically adapt the number as well as the structure of the map according to identified topics. Unlike other data-oriented SOMs, our approach expands the map and generates the hierarchies both according to the topics and their characteristics of the neurons. The preliminary experiments give promising result and demonstrate the plausibility of the method.
Digital Article Identifier (DOI):
156
4928
NFκB Pathway Modeling for Optimal Drug Combination Therapy on Multiple Myeloma
Abstract: NFκB activation plays a crucial role in anti-apoptotic responses in response to the apoptotic signaling during tumor necrosis factor (TNFa) stimulation in Multiple Myeloma (MM). Although several drugs have been found effective for the treatment of MM by mainly inhibiting NFκB pathway, there are no any quantitative or qualitative results of comparison assessment on inhibition effect between different single drugs or drug combinations. Computational modeling is becoming increasingly indispensable for applied biological research mainly because it can provide strong quantitative predicting power. In this study, a novel computational pathway modeling approach is employed to comparably assess the inhibition effects of specific single drugs and drug combinations on the NFκB pathway in MM, especially the prediction of synergistic drug combinations.
Digital Article Identifier (DOI):
155
1281
Numerical Algorithms for Solving a Type of Nonlinear Integro-Differential Equations
Abstract: In this article two algorithms, one based on variation iteration method and the other on Adomian's decomposition method, are developed to find the numerical solution of an initial value problem involving the non linear integro differantial equation where R is a nonlinear operator that contains partial derivatives with respect to x. Special cases of the integro-differential equation are solved using the algorithms. The numerical solutions are compared with analytical solutions. The results show that these two methods are efficient and accurate with only two or three iterations
Digital Article Identifier (DOI):
154
6411
The Smoke Suppression Effect of Copper Oxideon the Epoxy Resin/Intumescent Flame Retardant/Titanate Couple Agent System
Abstract: Fire disaster is the major factor to endanger the public
and environmental safety. People lost their life during fire disaster
mainly be attributed to the dense smoke and toxic gas under
combustion, which hinder the escape of people and the rescue of
firefighters under fire disaster. The smoke suppression effect of
several transitional metals oxide on the epoxy resin treated with
intumescent flame retardant and titanate couple agent
(EP/IFR/Titanate) system have been investigated. The results showed
manganese dioxide has great effect on reducing the smoke density rate
(SDR) of EP/IFR/Titanate system; however it has little effect to reduce
the maximum smoke density (MSD) of EP/IFR/Titanate system.
Copper oxide can decrease the maximum smoke density (MSD) and
smoke density rate of EP/IFR/Titanate system substantially. The MSD
and SDR of EP/IFR/Titanate system can reduce 20.3% and 39.1%
respectively when 2% of copper oxide is introduced.
Digital Article Identifier (DOI):
153
6920
Evaluating Service Quality of Online Auction by Fuzzy MCDM
Abstract: This paper applies fuzzy set theory to evaluate the
service quality of online auction. Service quality is a composition of
various criteria. Among them many intangible attributes are difficult
to measure. This characteristic introduces the obstacles for respondent
in replying to the survey. So as to overcome this problem, we
invite fuzzy set theory into the measurement of performance. By
using AHP in obtaining criteria and TOPSIS in ranking, we found
the most concerned dimension of service quality is Transaction
Safety Mechanism and the least is Charge Item. Regarding to the
most concerned attributes are information security, accuracy and
information.
Digital Article Identifier (DOI):
152
9045
Frequency-Domain Design of Fractional-Order FIR Differentiators
Abstract: In this paper, a fractional-order FIR differentiator
design method using the differential evolution (DE) algorithm is
presented. In the proposed method, the FIR digital filter is designed to
meet the frequency response of a desired fractal-order differentiator,
which is evaluated in the frequency domain. To verify the design
performance, another design method considered in the time-domain is
also provided. Simulation results reveal the efficiency of the proposed
method.
Digital Article Identifier (DOI):
151
12775
Bifurcation Analysis of Horizontal Platform System
Abstract: Horizontal platform system (HPS) is popularly applied
in offshore and earthquake technology, but it is difficult and
time-consuming for regulation. In order to understand the nonlinear
dynamic behavior of HPS and reduce the cost when using it, this paper
employs differential transformation method to study the bifurcation
behavior of HPS. The numerical results reveal a complex dynamic
behavior comprising periodic, sub-harmonic, and chaotic responses.
Furthermore, the results reveal the changes which take place in the
dynamic behavior of the HPS as the external torque is increased.
Therefore, the proposed method provides an effective means of
gaining insights into the nonlinear dynamics of horizontal platform
system.
Digital Article Identifier (DOI):
150
12644
A Two-Channel Secure Communication Using Fractional Chaotic Systems
Abstract: In this paper, a two-channel secure communication
using fractional chaotic systems is presented. Conditions for chaos
synchronization have been investigated theoretically by using Laplace
transform. To illustrate the effectiveness of the proposed scheme, a
numerical example is presented. The keys, key space, key selection
rules and sensitivity to keys are discussed in detail. Results show that
the original plaintexts have been well masked in the ciphertexts yet
recovered faithfully and efficiently by the present schemes.
Digital Article Identifier (DOI):
149
11587
Low Power Low Voltage Current Mode Pipelined A/D Converters
Abstract: This paper presents two prototypes of low power low voltage current mode 9 bit pipelined a/d converters. The first and the second converters are configured of 1.5 bit and 2.5 bit stages, respectively. The a/d converter structures are composed of current mode building blocks and final comparator block which converts the analog current signal into digital voltage signal. All building blocks have been designed in CMOS AMS 0.35μm technology, then simulated to verify proposed concept. The performances of both converters are compared to performances of known current mode and voltage mode switched capacitance converter structures. Low power consumption and small chip area are advantages of the proposed converters.
Digital Article Identifier (DOI):
148
13612
The Effect of Risky Assets to Operating Efficiencies for Listed Securities Firms in Taiwan Using the Data Envelopment Analysis
Abstract: This paper employs a the variable returns to scale DEA
model to take account of risky assets and estimate the operating
efficiencies for the 21 domestic listed securities firms during the
period 2005-2009. Evidence is found that on average the brokerage
securities firms- operating efficiencies are better than integrated
securities firms. Evidence is also found that the technical inefficiency
from inappropriate management constitutes the main source of the
operating inefficiency for both types of securities firms. Moreover, the
scale economies prevail in brokerage and integrated securities firms,
in other words, which exhibit the characteristic of increasing returns to
scale.
Digital Article Identifier (DOI):
147
13385
Identification Characterization and Production of Phytase from Endophytic Fungi
Abstract: Phytases are acid phosphatase enzymes, which
efficiently cleave phosphate moieties from phytic acid, thereby
generating myo-inositol and inorganic phosphate. Thirty four
isolates of endophytic fungi to produce of phytases were isolated
from leaf, stem and root fragments of soybean. Screening of 34
isolates of endophytic fungi identified the phytases produced by
Rhizoctonia sp. and Fusarium verticillioides . The phytase
production were the best induced by phytic acid and rice bran
compared the others inducer in submerged fermentation medium
used. The phytase produced by both Rhizoctonia sp. and F.
verticillioides have pH optimum at 4.0 and 5.0 respectively. The
characterization of phytase from Fusarium verticillioides showed that
temperature optimum was 500C and stability until 600C, the pH
optimum 5.0 and pH stability was 2.5 – 6.0, and substrate specificity
were rice bran>soybean meal>corn> coconut cake, respectively.
Digital Article Identifier (DOI):
146
8898
Phosphorus Supplementation of Ammoniated Rice Straw on Rumen Fermentability, Syntesised Microbial Protein and Degradabilityin Vitro
Abstract: The effect of phosphorus supplementation of ammoniated rice straw was studied. The in vitro experiment was carried out following the first stage of Tilley and Terry method. The treatments consisting of four diets were A = 50% ammoniated rice straw + 50% concentrate (control), B = A + 0.2% Phosphor (P) supplement, C = A + 0.4% Phosphor (P) supplement, and D = A + 0.6% Phosphor (P) supplement of dry matter. Completely randomized design was used as the experimental design with differences among treatment means were examined using Duncan multiple range test. Variables measured were total bacterial and cellulolytic bacterial population, cellulolytic enzyme activity, ammonia (NH3) and volatile fatty acid (VFA) concentrations, as fermentability indicators and synthesized microbial protein, as well as degradability indicators including dry matter (DM), organic matter (OM), neutral detergent fibre (NDF), acid detergent fibre (ADF) and cellulose. The results indicated that fermentability and degradability of diets consisting ammoniated rice straw with P supplementation were significantly higher than the control diet (P< 0.05). It is concluded that P supplementation is important to improve fermentability and degradability of rations containing ammoniated RS and concentrate. In terms of the most effective level of P supplementation occurred at a supplementation rate of 0.4% of dry matter.
Digital Article Identifier (DOI):
145
2600
Negative Selection as a Means of Discovering Unknown Temporal Patterns
Abstract: The temporal nature of negative selection is an under exploited area. In a negative selection system, newly generated antibodies go through a maturing phase, and the survivors of the phase then wait to be activated by the incoming antigens after certain number of matches. These without having enough matches will age and die, while these with enough matches (i.e., being activated) will become active detectors. A currently active detector may also age and die if it cannot find any match in a pre-defined (lengthy) period of time. Therefore, what matters in a negative selection system is the dynamics of the involved parties in the current time window, not the whole time duration, which may be up to eternity. This property has the potential to define the uniqueness of negative selection in comparison with the other approaches. On the other hand, a negative selection system is only trained with “normal" data samples. It has to learn and discover unknown “abnormal" data patterns on the fly by itself. Consequently, it is more appreciate to utilize negation selection as a system for pattern discovery and recognition rather than just pattern recognition. In this paper, we study the potential of using negative selection in discovering unknown temporal patterns.
Digital Article Identifier (DOI):
144
14461
A Lifetime-Guaranteed Routing Scheme in Wireless Sensor Networks
Abstract: In this paper, we propose a routing scheme that guarantees
the residual lifetime of wireless sensor networks where each
sensor node operates with a limited budget of battery energy. The
scheme maximizes the communications QoS while sustaining the
residual battery lifetime of the network for a specified duration.
Communication paths of wireless nodes are translated into a directed
acyclic graph(DAG) and the maximum-flow algorithm is applied to
the graph. The found maximum flow are assigned to sender nodes, so
as to maximize their communication QoS. Based on assigned flows,
the scheme determines the routing path and the transmission rate of
data packet so that any sensor node on the path would not exhaust
its battery energy before a specified duration.
Digital Article Identifier (DOI):
143
4567
Influence of Slope Shape and Surface Roughness on the Moving Paths of a Single Rockfall
Abstract: Rockfall is a kind of irregular geological disaster. Its
destruction time, space and movements are highly random. The impact
force is determined by the way and velocity rocks move. The
movement velocity of a rockfall depends on slope gradient of its
moving paths, height, slope surface roughness and rock shapes. For
effectively mitigate and prevent disasters brought by rockfalls, it is
required to precisely calculate the moving paths of a rockfall so as to
provide the best protective design. This paper applies Colorado
Rockfall Simulation Program (CRSP) as our study tool to discuss the
impact of slope shape and surface roughness on the moving paths of a
single rockfall. The analytical results showed that the slope, m=1:1,
acted as the threshold for rockfall bounce height on a monoclinal slight
slope. When JRC ´╝£ 1.2, movement velocity reduced and bounce
height increased as JCR increased. If slope fixed and JRC increased,
the bounce height of rocks increased gradually with reducing
movement velocity. Therefore, the analysis on the moving paths of
rockfalls with CRSP could simulate bouncing of falling rocks. By
analyzing moving paths, velocity, and bounce height of falling rocks,
we could effectively locate impact points of falling rocks on a slope.
Such analysis can be served as a reference for future disaster
prevention and control.
Digital Article Identifier (DOI):
142
10615
Shelf Life Extension of Milk Pomade Sweet – Sherbet with Crunchy Peanut Chips by MAP in Various Packaging Materials
Abstract: The objective of the research was to evaluate the
hardness stability of milk pomade sweets packed in several
packaging materials (OPP, Multibarrier 60 HFP, BIALON 65
HFP, BIALON 50 HFP, ECOLEAN) by several packaging
technologies – modified atmosphere (MAP) (consisting of
30% CO2+70% N2; 30% N2+70% CO2 and 100% CO2) and
control – in air ambiance. Samples were stored at the room
temperature +21±1 °C. The studies of the samples were
carried out before packaging and after 2, 4, 6, 8, and 10
storage weeks.
Digital Article Identifier (DOI):
141
11405
Sous Vide Packaging Technology Application for Salad with Meat in Mayonnaise Shelf Life Extension
Abstract: Experiments have been carried out at the Latvia
University of Agriculture Department of Food Technology. The aim
of this work was to assess the effect of sous vide packaging during
the storage time of salad with meat in mayonnaise at different storage
temperature. Samples were evaluated at 0, 1, 3, 7, 10, 15, 18, 25, 29,
42, and 52 storage days at the storage temperature of +4±0.5 ºC and
+10±0.5 ºC. Experimentally the quality of the salad with meat in
mayonnaise was characterized by measuring colour, pH and
microbiological properties. The sous vide packaging was effective in
protecting the product from physical, chemical, and microbial quality
degradation. The sous vide packaging significantly reduces microbial
growth at storage temperature of +4±0.5 ºC and +10±0.5 ºC.
Moreover, it is possible to extend the product shelf life to 52 days
even when stored at +10±0.5 ºC.
Digital Article Identifier (DOI):
140
11272
Squaring Construction for Repeated-Root Cyclic Codes
Abstract: We considered repeated-root cyclic codes whose
block length is divisible by the characteristic of the underlying field.
Cyclic self dual codes are also the repeated root cyclic codes. It is
known about the one-level squaring construction for binary repeated
root cyclic codes. In this correspondence, we introduced of two
level squaring construction for binary repeated root cyclic codes of
length 2a b , a > 0, b is odd.
Digital Article Identifier (DOI):
139
13214
Processes Simulation Study of Coal to Methanol Based on Gasification Technology
Abstract: This study presents a simulation model for converting coal to methanol, based on gasification technology with the commercial chemical process simulator, Pro/II® V8.1.1. The methanol plant consists of air separation unit (ASU), gasification unit, gas clean-up unit, and methanol synthetic unit. The clean syngas is produced with the first three operating units, and the model has been verified with the reference data from United States Environment Protection Agency. The liquid phase methanol (LPMEOHTM) process is adopted in the methanol synthetic unit. Clean syngas goes through gas handing section to reach the reaction requirement, reactor loop/catalyst to generate methanol, and methanol distillation to get desired purity over 99.9 wt%. The ratio of the total energy combined with methanol and dimethyl ether to that of feed coal is 78.5% (gross efficiency). The net efficiency is 64.2% with the internal power consumption taken into account, based on the assumption that the efficiency of electricity generation is 40%.
Digital Article Identifier (DOI):
138
1779
Production of H5N1 Hemagglutinin inTrichoplusia ni Larvae by a Novel Bi-cistronic Baculovirus Expression Vector
Abstract: Highly pathogenic avian influenza (HPAI) H5N1 viruses have created demand for a cost-effective vaccine to prevent a pandemic of the disease. Here, we report that Trichoplusia ni (T. ni) larvae can act as a cost-effective bioreactor to produce recombinant HA5 (rH5HA) proteins as an potential effective vaccine for chickens. To facilitate the recombinant virus identification, virus titer determination and access the infected larvae, we employed the internal ribosome entry site (IRES) derived from Perina nuda virus (PnV, belongs to insect picorna like Iflavirus genus) to construct a bi-cistronic baculovirus expression vector that can express the rH5HA protein and enhanced green fluorescent protein (EGFP) simultaneously. Western blot analysis revealed that the 70 kDa rH5HA protein and partially cleaved products (40 kDa H5HA1) were generated in T. ni larvae infected with recombinant baculovirus carrying the H5HA gene. These data suggest that the baculovirus-larvae recombinant protein expression system could be a cost-effective platform for H5N1 vaccine production.
Digital Article Identifier (DOI):
137
13121
Optimal Generation Expansion Planning Strategy with Carbon Trading
Abstract: Fossil fuel-firing power plants dominate electric
power generation in Taiwan, which are also the major contributor to
Green House gases (GHG). CO2 is the most important greenhouse
gas that cause global warming. This paper penetrates the relationship
between carbon trading for GHG reduction and power generation
expansion planning (GEP) problem for the electrical utility. The
Particle Swarm Optimization (PSO) Algorithm is presented to deal
with the generation expansion planning strategy of the utility with
independent power providers (IPPs). The utility has to take both the
IPPs- participation and environment impact into account when a new
generation unit is considering expanded from view of supply side.
Digital Article Identifier (DOI):
136
15502
Polyisoprene-coated Silica/Natural Rubber Composite
Abstract: The commercial white tyres are usually used for forklifts in food and medicine industries. Conventionally, silica is used as reinforcement in the tyres. However, the adhesion between silica particles and rubber is remarkably poor. To improve the problem of adhesion and hence enhance wear resistance, modification of silica surface is one of the solutions. In this work, the natural rubber compound blending with polyisoprene-coated silica prepared by admicellar polymerization technique was studied to compare with the natural rubber compound of unmodified silica. The surface characterization of modified silica was also examined by SEM, FTIR, and TGA. The results show that polyisoprene-coated silica/natural rubber compound gave better overall mechanical properties, especially wear resistance with the improvement of the adhesion between silica and natural rubber matrix that can be seen in the SEM micrograph.
Digital Article Identifier (DOI):
135
11616
Energy Consumption and Carbon Calculations of Microalgae Biodiesel
Abstract: At present, the severe oil crisis and greenhouse effect are booming, which is a growing worry for China. Over a long period of study, choosing the development of biological diesel is a feasible way in the desertification region in China. With considering the adaptability of Micro-algae in desertification region and analyzing energy consumption and carbon calculations of Micro-algae biodiesel produced by JJ company , this paper, make the microalgae our optimal choice to develop biological diesel in china's desertification region.
Digital Article Identifier (DOI):
134
11140
Applying Fuzzy FP-Growth to Mine Fuzzy Association Rules
Abstract: In data mining, the association rules are used to find
for the associations between the different items of the transactions
database. As the data collected and stored, rules of value can be found
through association rules, which can be applied to help managers
execute marketing strategies and establish sound market frameworks.
This paper aims to use Fuzzy Frequent Pattern growth (FFP-growth)
to derive from fuzzy association rules. At first, we apply fuzzy
partition methods and decide a membership function of quantitative
value for each transaction item. Next, we implement FFP-growth
to deal with the process of data mining. In addition, in order to
understand the impact of Apriori algorithm and FFP-growth algorithm
on the execution time and the number of generated association
rules, the experiment will be performed by using different sizes of
databases and thresholds. Lastly, the experiment results show FFPgrowth
algorithm is more efficient than other existing methods.
Digital Article Identifier (DOI):
133
9670
Computer Models of the Vestibular Head Tilt Response, and Their Relationship to EVestG and Meniere's Disease
Abstract: This paper attempts to explain response components of Electrovestibulography (EVestG) using a computer simulation of a three-canal model of the vestibular system. EVestG is a potentially new diagnostic method for Meniere's disease. EVestG is a variant of Electrocochleography (ECOG), which has been used as a standard method for diagnosing Meniere's disease - it can be used to measure the SP/AP ratio, where an SP/AP ratio greater than 0.4-0.5 is indicative of Meniere-s Disease. In EVestG, an applied head tilt replaces the acoustic stimulus of ECOG. The EVestG output is also an SP/AP type plot, where SP is the summing potential, and AP is the action potential amplitude. AP is thought of as being proportional to the size of a population of afferents in an excitatory neural firing state. A simulation of the fluid volume displacement in the vestibular labyrinth in response to various types of head tilts (ipsilateral, backwards and horizontal rotation) was performed, and a simple neural model based on these simulations developed. The simple neural model shows that the change in firing rate of the utricle is much larger in magnitude than the change in firing rates of all three semi-circular canals following a head tilt (except in a horizontal rotation). The data suggests that the change in utricular firing rate is a minimum 2-3 orders of magnitude larger than changes in firing rates of the canals during ipsilateral/backward tilts. Based on these results, the neural response recorded by the electrode in our EVestG recordings is expected to be dominated by the utricle in ipsilateral/backward tilts (It is important to note that the effect of the saccule and efferent signals were not taken into account in this model). If the utricle response dominates the EVestG recordings as the modeling results suggest, then EVestG has the potential to diagnose utricular hair cell damage due to a viral infection (which has been cited as one possible cause of Meniere's Disease).
Digital Article Identifier (DOI):
132
12277
Motivated Support Vector Regression with Structural Prior Knowledge
Abstract: It-s known that incorporating prior knowledge into support
vector regression (SVR) can help to improve the approximation
performance. Most of researches are concerned with the incorporation
of knowledge in form of numerical relationships. Little work,
however, has been done to incorporate the prior knowledge on the
structural relationships among the variables (referred as to Structural
Prior Knowledge, SPK). This paper explores the incorporation of SPK
in SVR by constructing appropriate admissible support vector kernel
(SV kernel) based on the properties of reproducing kernel (R.K).
Three-levels specifications of SPK are studies with the corresponding
sub-levels of prior knowledge that can be considered for the method.
These include Hierarchical SPK (HSPK), Interactional SPK (ISPK)
consisting of independence, global and local interaction, Functional
SPK (FSPK) composed of exterior-FSPK and interior-FSPK. A
convenient tool for describing the SPK, namely Description Matrix
of SPK is introduced. Subsequently, a new SVR, namely Motivated
Support Vector Regression (MSVR) whose structure is motivated
in part by SPK, is proposed. Synthetic examples show that it is
possible to incorporate a wide variety of SPK and helpful to improve
the approximation performance in complex cases. The benefits of
MSVR are finally shown on a real-life military application, Air-toground
battle simulation, which shows great potential for MSVR to
the complex military applications.
Digital Article Identifier (DOI):
131
6239
Synthesis and Properties of Biobased Polyurethane/Montmorillonite Nanocomposites
Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Digital Article Identifier (DOI):
130
13174
Trajectory Control of a Robotic Manipulator Utilizing an Adaptive Fuzzy Sliding Mode
Abstract: In this paper, a novel adaptive fuzzy sliding mode
control method is proposed for the robust tracking control of robotic
manipulators. The proposed controller possesses the advantages of
adaptive control, fuzzy control, and sliding mode control. First, system
stability and robustness are guaranteed based on the sliding mode
control. Further, fuzzy rules are developed incorporating with
adaptation law to alleviate the input chattering effectively. Stability of
the control system is proven by using the Lyapunov method. An
application to a three-degree-of-freedom robotic manipulator is
carried out. Accurate trajectory tracking as well as robustness is
achieved. Input chattering is greatly eliminated.
Digital Article Identifier (DOI):
129
3443
Framework for Delivery Reliability in European Machinery and Equipment Industry
Abstract: Today-s manufacturing companies are facing multiple and dynamic customer-supplier-relationships embedded in nonhierarchical production networks. This complex environment leads to problems with delivery reliability and wasteful turbulences throughout the entire network. This paper describes an operational model based on a theoretical framework which improves delivery reliability of each individual customer-supplier-relationship within non-hierarchical production networks of the European machinery and equipment industry. By developing a non-centralized coordination mechanism based on determining the value of delivery reliability and derivation of an incentive system for suppliers the number of in time deliveries can be increased and thus the turbulences in the production network smoothened. Comparable to an electronic stock exchange the coordination mechanism will transform the manual and nontransparent process of determining penalties for delivery delays into an automated and transparent market mechanism creating delivery reliability.
Digital Article Identifier (DOI):
128
12938
Prediction of Protein Subchloroplast Locations using Random Forests
Abstract: Protein subchloroplast locations are correlated with its
functions. In contrast to the large amount of available protein
sequences, the information of their locations and functions is less
known. The experiment works for identification of protein locations
and functions are costly and time consuming. The accurate prediction
of protein subchloroplast locations can accelerate the study of
functions of proteins in chloroplast. This study proposes a Random
Forest based method, ChloroRF, to predict protein subchloroplast
locations using interpretable physicochemical properties. In addition
to high prediction accuracy, the ChloroRF is able to select important
physicochemical properties. The important physicochemical
properties are also analyzed to provide insights into the underlying
mechanism.
Digital Article Identifier (DOI):
127
3950
Sequence-based Prediction of Gamma-turn Types using a Physicochemical Property-based Decision Tree Method
Abstract: The γ-turns play important roles in protein folding and
molecular recognition. The prediction and analysis of γ-turn types are
important for both protein structure predictions and better
understanding the characteristics of different γ-turn types. This study
proposed a physicochemical property-based decision tree (PPDT)
method to interpretably predict γ-turn types. In addition to the good
prediction performance of PPDT, three simple and human
interpretable IF-THEN rules are extracted from the decision tree
constructed by PPDT. The identified informative physicochemical
properties and concise rules provide a simple way for discriminating
and understanding γ-turn types.
Digital Article Identifier (DOI):
126
690
One-Class Support Vector Machines for Aerial Images Segmentation
Abstract: Interpretation of aerial images is an important task in
various applications. Image segmentation can be viewed as the essential
step for extracting information from aerial images. Among many
developed segmentation methods, the technique of clustering has been
extensively investigated and used. However, determining the number
of clusters in an image is inherently a difficult problem, especially
when a priori information on the aerial image is unavailable. This
study proposes a support vector machine approach for clustering
aerial images. Three cluster validity indices, distance-based index,
Davies-Bouldin index, and Xie-Beni index, are utilized as quantitative
measures of the quality of clustering results. Comparisons on the
effectiveness of these indices and various parameters settings on the
proposed methods are conducted. Experimental results are provided
to illustrate the feasibility of the proposed approach.
Digital Article Identifier (DOI):
125
3225
Direct and Indirect Somatic Embryogenesis from Petiole and Leaf Explants of Purple Fan Flower (Scaevola aemula R. Br. cv. 'Purple Fanfare')
Abstract: Direct and indirect somatic embryogenesis (SE) from
petiole and leaf explants of Scaevola aemula R. Br. cv. 'Purple
Fanfare' was achieved. High frequency of somatic embryos was
obtained directly from petiole and leaf explants using an inductive
plant growth regulator signal thidiazuron (TDZ). Petiole explants
were more responsive to SE than leaves. Plants derived from somatic
embryos of petiole explants germinated more readily into plants. SE
occurred more efficiently in half-strength Murashige and Skoog
(MS) medium than in full-strength MS medium. Non-embryogenic
callus induced by 2, 4-dichlorophenoxyacetic acid was used to
investigate the feasibility of obtaining SE with TDZ as a secondary
inductive plant growth regulator (PGR) signal. Non-embryogenic
callus of S. aemula was able to convert into an “embryogenic
competent mode" with PGR signal. Protocol developed for induction
of direct and indirect somatic embryogenesis in S. aemula can
improve the large scale propagation system of the plant in future.
Digital Article Identifier (DOI):
124
2938
Toxicity of Copper and Cadmium to Freshwater Fishes
Abstract: Two freshwater fishes, Rasbora sumatrana
(Cyprinidae) and Poecilia reticulata (guppy) (Poeciliidae) were
exposed for a four-day period in the laboratory condition to a range
of copper (Cu) and cadmium (Cd) concentrations. Mortality was
assessed and median lethal concentrations (LC50) were calculated.
LC50 increased with decrease in mean exposure times for both metals.
For R. sumatrana, LC50s for 24, 48, 72 and 96 hours for Cu were
54.2, 30.3, 18.9 and 5.6 μg/L and for Cd 1440.2, 459.3, 392.3 and
101.6 μg/L respectively. For P. reticulata, LC50s for 24, 48, 72 and
96 hours for Cu were 348.9, 145.4, 61.3 and 37.9 μg/L and for Cd
8205.6, 2827.1, 405.8 and 168.1 μg/L, respectively. Results indicated
that the Cu was more toxic than Cd to both fishes (Cu>Cd) and R.
sumatrana was more sensitive than P. reticulata to the metals.
Digital Article Identifier (DOI):
123
3720
Fabrication and Characterization of Sawdust Composite Biodegradable Film
Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Digital Article Identifier (DOI):
122
11918
On the Use of Correlated Binary Model in Social Network Analysis
Abstract: In social network analysis the mean nodal degree and
density of the graph can be considered as a measure of the activity of
all actors in the network and this is an important property of a graph
and for making comparisons among networks. Since subjects in a
family or organization are subject to common environment factors, it
is prime interest to study the association between responses.
Therefore, we study the distribution of the mean nodal degree and
density of the graph under correlated binary units. The cross product
ratio is used to capture the intra-units association among subjects.
Computer program and an application are given to show the benefits
of the method.
Digital Article Identifier (DOI):
121
6049
A Contribution to 3D Modeling of Manufacturing Tolerance Optimization
Abstract: The study of the generated defects on manufactured
parts shows the difficulty to maintain parts in their positions during
the machining process and to estimate them during the pre-process
plan. This work presents a contribution to the development of 3D
models for the optimization of the manufacturing tolerances. An
experimental study allows the measurement of the defects of part
positioning for the determination of ε and the choice of an optimal
setup of the part. An approach of 3D tolerance based on the small
displacements method permits the determination of the
manufacturing errors upstream. A developed tool, allows an
automatic generation of the tolerance intervals along the three axes.
Digital Article Identifier (DOI):
120
13384
Self-evolving Artificial Immune System via Developing T and B Cell for Permutation Flow-shop Scheduling Problems
Abstract: Artificial Immune System is applied as a Heuristic
Algorithm for decades. Nevertheless, many of these applications
took advantage of the benefit of this algorithm but seldom proposed
approaches for enhancing the efficiency. In this paper, a
Self-evolving Artificial Immune System is proposed via developing
the T and B cell in Immune System and built a self-evolving
mechanism for the complexities of different problems. In this
research, it focuses on enhancing the efficiency of Clonal selection
which is responsible for producing Affinities to resist the invading of
Antigens. T and B cell are the main mechanisms for Clonal
Selection to produce different combinations of Antibodies.
Therefore, the development of T and B cell will influence the
efficiency of Clonal Selection for searching better solution.
Furthermore, for better cooperation of the two cells, a co-evolutional
strategy is applied to coordinate for more effective productions of
Antibodies. This work finally adopts Flow-shop scheduling
instances in OR-library to validate the proposed algorithm.
Digital Article Identifier (DOI):
119
13155
Image Enhancement of Medical Images using Gabor Filter Bank on Hexagonal Sampled Grids
Abstract: For about two decades scientists have been
developing techniques for enhancing the quality of medical images
using Fourier transform, DWT (Discrete wavelet transform),PDE
model etc., Gabor wavelet on hexagonal sampled grid of the images
is proposed in this work. This method has optimal approximation
theoretic performances, for a good quality image. The computational
cost is considerably low when compared to similar processing in the
rectangular domain. As X-ray images contain light scattered pixels,
instead of unique sigma, the parameter sigma of 0.5 to 3 is found to
satisfy most of the image interpolation requirements in terms of high
Peak Signal-to-Noise Ratio (PSNR) , lower Mean Squared Error
(MSE) and better image quality by adopting windowing technique.
Digital Article Identifier (DOI):
118
1493
Visual Cryptography by Random Grids with Identifiable Shares
Abstract: This paper proposes a visual cryptography by random
grids scheme with identifiable shares. The method encodes an image
O in two shares that exhibits the following features: (1) each generated
share has the same scale as O, (2) any share singly has noise-like
appearance that reveals no secret information on O, (3) the secrets can
be revealed by superimposing the two shares, (4) folding a share up
can disclose some identification patterns, and (5) both of the secret
information and the designated identification patterns are recognized
by naked eye without any computation. The property to show up
identification patterns on folded shares establishes a simple and
friendly interface for users to manage the numerous shares created by
VC schemes.
Digital Article Identifier (DOI):
117
14070
A Simulation Model for Bid Price Decision Making
Abstract: In Lebanon, public construction projects are awarded
to the contractor submitting the lowest bid price based on a
competitive bidding process. The contractor has to make a strategic
decision in choosing the appropriate bid price that will offer a
satisfactory profit with a greater probability to win. A simulation
model for bid price decision making based on the lowest bid price
evaluation is developed. The model, built using Crystal Ball decisionengineering
software, considers two main factors affecting the
bidding process: the number of qualified bidders and the size of the
project. The validity of the model is tested on twelve separate
projects. The study also shows how to use the model to conduct risk
analysis and help any specific contractor to decide on his bid price
with associated certainty level in a scientific method.
Digital Article Identifier (DOI):
116
2656
2D Image Processing for DSO Astrophotography
Abstract: The new concept of two–dimensional (2D) image
processing implementation for auto-guiding system is shown in this
paper. It is dedicated to astrophotography and operates with
astronomy CCD guide cameras or with self-guided dual-detector
CCD cameras and ST4 compatible equatorial mounts. This idea was
verified by MATLAB model, which was used to test all procedures
and data conversions. Next the circuit prototype was implemented at
Altera MAX II CPLD device and tested for real astronomical object
images. The digital processing speed of CPLD prototype board was
sufficient for correct equatorial mount guiding in real-time system.
Digital Article Identifier (DOI):
115
10069
Adsorption of Crystal Violet onto BTEA- and CTMA-bentonite from Aqueous Solutions
Abstract: CTMA-bentonite and BTEA-Bentonite prepared by Na-bentonite cation exchanged with cetyltrimethylammonium(CTMA) and benzyltriethylammonium (BTEA). Products were characterized by XRD and IR techniques.The d001 spacing value of CTMA-bentonite and BTEA-bentonite are 7.54Å and 3.50Å larger than that of Na-bentonite at 100% cation exchange capacity, respectively. The IR spectrum showed that the intensities of OH stretching and bending vibrations of the two organoclays decreased greatly comparing to untreated Na-bentonite. Batch experiments were carried out at 303 K, 318 K and 333 K to obtain the sorption isotherms of Crystal violet onto the two organoclays. The results show that the sorption isothermal data could be well described by Freundlich model. The dynamical data for the two organoclays fit well with pseudo-second-order kinetic model. The adsorption capacity of CTMA-bentonite was found higher than that of BTEA-Bentonite. Thermodynamic parameters such as changes in the free energy (ΔG°), the enthalpy (ΔH°) and the entropy (ΔS°) were also evaluated. The overall adsorption process of Crystal violet onto the two organoclays were spontaneous, endothermic physisorption. The CTMA-bentonite and BTEA-Bentonite could be employed as low-cost alternatives to activated carbon in wastewater treatment for the removal of color which comes from textile dyes.
Digital Article Identifier (DOI):
114
4961
Reconfigurable Autonomous Mini Robot Design using CPLD's
Abstract: This paper explains a project based learning method where autonomous mini-robots are developed for research, education and entertainment purposes. In case of remote systems wireless sensors are developed in critical areas, which would collect data at specific time intervals, send the data to the central wireless node based on certain preferred information would make decisions to turn on or off a switch or control unit. Such information transfers hardly sums up to a few bytes and hence low data rates would suffice for such implementations. As a robot is a multidisciplinary platform, the interfacing issues involved are discussed in this paper. The paper is mainly focused on power supply, grounding and decoupling issues.
Digital Article Identifier (DOI):
113
2216
Grouping-Based Job Scheduling Model In Grid Computing
Abstract: Grid computing is a high performance computing
environment to solve larger scale computational applications. Grid
computing contains resource management, job scheduling, security
problems, information management and so on. Job scheduling is a
fundamental and important issue in achieving high performance in
grid computing systems. However, it is a big challenge to design an
efficient scheduler and its implementation. In Grid Computing, there
is a need of further improvement in Job Scheduling algorithm to
schedule the light-weight or small jobs into a coarse-grained or
group of jobs, which will reduce the communication time,
processing time and enhance resource utilization. This Grouping
strategy considers the processing power, memory-size and
bandwidth requirements of each job to realize the real grid system.
The experimental results demonstrate that the proposed scheduling
algorithm efficiently reduces the processing time of jobs in
comparison to others.
Digital Article Identifier (DOI):
112
8060
The Current Implementation Status of Manufacturing Control Systems for a Key Manufacturing Industry
Abstract: Manufacturing, production and service industries within Libya have struggled with many problems during the past two decades due to many difficulties. These problems have created a negative impact on the productivity and utilization of many industries around the country. This paper studies the implementation levels of the manufacturing control systems known as Manufacturing Resource Planning (MRPII) being adapted within some Libyan industries. A survey methodology has been applied for this research, based on the survey analysis, the results pointed out that the system within these industries has a modest strategy towards most of the areas that are considered as being very crucial in implementing these systems successfully. The findings also show a variation within these implementation levels with a respect to the key-elements that related to MRPII, giving the highest levels in the emphasise on financial data accuracy. The paper has also identified limitations within the investigated manufacturing and managerial areas and has pointed to where senior managers should take immediate actions in order to achieve effective implementation of MRPII within their business area.
Digital Article Identifier (DOI):
111
1937
Analysis of Production Loss on a Linear Walking Worker Line
Abstract: This paper mathematically analyses the varying
magnitude of production loss, which may occur due to idle time (inprocess
waiting time and traveling time) on a linear walking worker
assembly line. Within this flexible and reconfigurable assembly
system, each worker travels down the line carrying out each
assembly task at each station; and each worker accomplishes the
assembly of a unit from start to finish and then travels back to the
first station to start the assembly of a new product. This strategy of
system design attempts to combine the flexibility of the U-shaped
moving worker assembly cell with the efficiency of the conventional
fixed worker assembly line. The paper aims to evaluate the effect of
idle time that may offset the labor efficiency of each walking worker
providing an insight into the mechanism of such a flexible and
reconfigurable assembly system.
Digital Article Identifier (DOI):
110
668
Water Boundary Layer Flow Over Rotating Sphere with Mass Transfer
Abstract: An analysis is performed to study the influence of nonuniform double slot suction on a steady laminar boundary layer flow over a rotating sphere when fluid properties such as viscosity and Prandtl number are inverse linear functions of temperature. Nonsimilar solutions have been obtained from the starting point of the streamwise co-ordinate to the exact point of separation. The difficulties arising at the starting point of the streamwise co-ordinate, at the edges of the slot and at the point of separation have been overcome by applying an implicit finite difference scheme in combination with the quasi-linearization technique and an appropriate selection of the finer step sizes along the stream-wise direction. The present investigation shows that the point of ordinary separation can be delayed by nonuniform double slot suction if the mass transfer rate is increased and also if the slots are positioned further downstream. In addition, the investigation reveals that double slot suction is found to be more effective compared to a single slot suction in delaying ordinary separation. As rotation parameter increase the point of separation moves upstream direction.
Digital Article Identifier (DOI):
109
6216
Adoption of E-Business by Thai SMEs
Abstract: The use of e-business in small and medium-sized
enterprises (SMEs) has been recently received an enormous attention
in information systems research by both academic and practitioners.
With the adoption of new and efficient technologies to enhance
businesses, Thai SMEs should be able to compete worldwide.
Unfortunately, most of the owners are not used to new technologies.
It is clear that most Thai SMEs prefer to work manually rather than
electronically. This paper aims to provide a fundamental conceptual
framework for E-business adoption by Thai SMEs. Rooted in
Knowledge transfer model, several factors are identified, which drive
and enable e-business adoption. By overlooking the benefits
associated with implementing new technologies, it is difficult for
Thai SMEs to perform well enough to compete globally. The paper
also helps Thai SMEs to understand factors related to E-business
adoption.
Digital Article Identifier (DOI):
108
14140
Haematological Characterization of Reproductive Status at Laying Hens by Age
Abstract: Physiological activity of the pineal gland with specific
responses in the reproductive territory may be interpreted by
monitoring the process parameters used in poultry practice in
different age batches of laying hens. As biological material were
used 105 laying hens, clinically healthy, belonging to ALBO SL-
2000 hybrid, raised on ground, from which blood samples were taken
at the age of 12 and 28 weeks. The haematological examinations
were concerned to obtain the total number of erythrocytes and
leukocytes and the main erythrocyte constant (RBC, PCV, MCV,
MCH, MCHC and WBC). The results allow the interpretation of the
reproductive status through the dynamics of the presented values.
Digital Article Identifier (DOI):
107
10707
Changes of Poultry Meat Chemical Composition, in Relationship with Lighting Schedule
Abstract: The paper is included within the framework of a
complex research program, which was initiated from the hypothesis
arguing on the existence of a correlation between pineal indolic and
peptide hormones and the somatic development rhythm, including
thus the epithalamium-epiphysis complex involvement. At birds,
pineal gland contains a circadian oscillator, playing a main role in the
temporal organization of the cerebral functions. The secretion of
pineal indolic hormones is characterized by a high endogenous
rhythmic alternation, modulated by the light/darkness (L/D)
succession and by temperature as well. The research has been carried
out using 100 chicken broilers - “Ross" commercial hybrid,
randomly allocated in two experimental batches: Lc batch, reared
under a 12L/12D lighting schedule and Lexp batch, which was photic
pinealectomised through continuous exposition to light (150 lux, 24
hours, 56 days). Chemical and physical features of the meat issued
from breast fillet and thighs muscles have been studied, determining
the dry matter, proteins, fat, collagen, salt content and pH value, as
well. Besides the variations of meat chemical composition in relation
with lighting schedule, other parameters have been studied: live
weight dynamics, feed intake and somatic development degree. The
achieved results became significant since chickens have 7 days of
age, some variations of the studied parameters being registered,
revealing that the pineal gland physiologic activity, in relation with
the lighting schedule, could be interpreted through the monitoring of
the somatic development technological parameters, usually studied
within the chicken broilers rearing aviculture practice.
Digital Article Identifier (DOI):
106
13293
On the Influence of Certain Natural Factors on the Sperm Quality and Sexual Behaviour of Rams
Abstract: In the Northern hemisphere, sheep reproduction is
seasonal (September-November). Among several natural factors
influencing the reproduction status of rams, we studied the daylight
length and temperature. Rams from different breeds were studied:
Merinos de Palas (half-precocious), Karakul de Botosani (halfbelated)
and Turcana (belated breed, low reproductive plasticity). In
Merinos de Palas, ejaculate volume during sexual repose is 51.3%
from normal quantity. When autumn climate was experimentally
induced, ejaculate volume reached 98.45% (Merinos), 94.97%
(Karakul) and 97.59% (Turcana). Semen density increased from
1.031-1.033 till 1.035 after exposition to artificial light and
temperature conditions. Spermatozoids mobility and sperm pH
improved, passing over 82% and 6.75, values identical to those in the
natural reproduction season. Behaviour analysis after
photoperiodicity indicated that over 83.3% Merinos and Karakul
males and all Turcana rams exteriorised normal and intense sexual
reflexes. Certain effort and reduced expenses brought rams in good
condition, producing higher quantity and quality sperm.
Digital Article Identifier (DOI):
105
1199
Growth Effects of Caffeic Acid and Thioglycolic Acid Modified Chitosans in U937 Cells
Abstract: Chitosan is a biopolymer composed of glucosamine
and N-acetyl glucosamine. Solubility and viscosity pose problems in
some applications. These problems can be overcome with unique
modifications. In this study, firstly, chitosan was modified by caffeic
acid and thioglycolic acid, separately. Then, growing effects of these
modified polymers was observed in U937 cell line. Caffeic acid is a
phenolic compound and its modifications act carcinogenic inhibitors
in drugs. Thiolated chitosans are commonly being used for drugdelivery
systems in various routes, because of enhancing
mucoadhesiveness property. U937 cell line was used model cell for
leukaemia. Modifications were achieved by 1 – 15 % binding range.
Increasing binding ratios showed higher radical-scavenging activity
and reducing cell growth, in compared to native chitosan. Caffeic
acid modifications showed higher radical-scavenging activity than
thiolated chitosans at the same concentrations. Caffeic acid and
thioglycolic acid modifications inhibited growth of U937, effectively.
Digital Article Identifier (DOI):
104
7922
Generating Concept Trees from Dynamic Self-organizing Map
Abstract: Self-organizing map (SOM) provides both clustering and visualization capabilities in mining data. Dynamic self-organizing maps such as Growing Self-organizing Map (GSOM) has been developed to overcome the problem of fixed structure in SOM to enable better representation of the discovered patterns. However, in mining large datasets or historical data the hierarchical structure of the data is also useful to view the cluster formation at different levels of abstraction. In this paper, we present a technique to generate concept trees from the GSOM. The formation of tree from different spread factor values of GSOM is also investigated and the quality of the trees analyzed. The results show that concept trees can be generated from GSOM, thus, eliminating the need for re-clustering of the data from scratch to obtain a hierarchical view of the data under study.
Digital Article Identifier (DOI):
103
6622
Quantitative Determination of Trace Elements in Some Oriental Herb Products
Abstract: The quantitative determination of several trace
elements (Cr, As, Se, Cd, Hg, Pb) existing as inorganic impurities in
some oriental herb-products such as Lingzhi Mushroom capsules,
Philamin powder, etc using ICP-MS has been studied. Various
instrumental parameters such as power, gas flow rate, sample depth, as
well as the concentration of nitric acid and thick background due to
high concentration of possible interferences on the determination of
these above-mentioned elements was investigated and the optimum
working conditions of the sample measurement on ICP-MS
(Agilent-7500a) were reported. Appropriate isotope internal standards
were also used to improve the accuracy of mercury determination.
Optimal parameters for sampling digestion were also investigated. The
recovery of analytical procedure was examined by using a Certified
Reference Material (IAEA-CRM 359). The recommended procedure
was then applied for the quantitative determination of Cr, As, Se, Cd,
Hg, Pb in Lingzhi Mushroom capsule, and Philamine powder samples.
The reproducibility of sample measurement (average value between
94 and 102%) and the uncertainty of analytical data (less than 20%)
are acceptable.
Digital Article Identifier (DOI):
102
7660
Clamped-clamped Boundary Conditions for Analysis Free Vibration of Functionally Graded Cylindrical Shell with a Ring based on Third Order Shear Deformation Theory
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally graded
materials (FGMs) composed of stainless steel and nickel is presented.
Material properties vary along the thickness direction of the shell
according to volume fraction power law. The cylindrical shells have
ring supports which are arbitrarily placed along the shell and impose
zero lateral deflections. The study is carried out based on third order
shear deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Digital Article Identifier (DOI):
101
2551
A Survey on Supply Chain Management and E Commerce Technology Adoption among Logistics Service Providers in Johor
Abstract: Logistics is part of the supply chain processes that plans, implements, and controls the efficient and effective forward and reverse flow and storage of goods, services, and related information between the point of origin and the point of consumption in order to meet customer requirements. This research aims to investigate the current status and future direction of the use of Information Technology (IT) for logistics, focusing on Supply Chain Management (SCM) and E-Commerce adoption in Johor. Therefore, this research stresses on the type of technology being adopted, factors, benefits and barriers affecting the innovation in SCM and ECommerce technology adoption among Logistics Service Providers (LSP). A mailed questionnaire survey was conducted to collect data from 265 logistics companies in Johor. The research revealed that SCM technology adoption among LSP was higher as they had adopted SCM technology in various business processes while they perceived a high level of benefits from SCM adoption. Obviously, ECommerce technology adoption among LSP is relatively low.
Digital Article Identifier (DOI):
100
11390
Strategic Information in the Game of Go
Abstract: We introduce a novel approach to measuring how
humans learn based on techniques from information theory and
apply it to the oriental game of Go. We show that the total amount
of information observable in human strategies, called the strategic
information, remains constant for populations of players of differing
skill levels for well studied patterns of play. This is despite the very
large amount of knowledge required to progress from the recreational
players at one end of our spectrum to the very best and most
experienced players in the world at the other and is in contrast to
the idea that having more knowledge might imply more 'certainty'
in what move to play next. We show this is true for very local
up to medium sized board patterns, across a variety of different
moves using 80,000 game records. Consequences for theoretical and
practical AI are outlined.
Digital Article Identifier (DOI):
99
14627
Reconfigurable Circularly Polarized Compact Short Backfire Antenna
Abstract: In this research paper, a slotted coaxial line fed cross
dipole excitation structure for short backfire antenna is proposed and
developed to achieve reconfigurable circular polarization. The cross
dipole, which is fed by the slotted coaxial line, consists of two
orthogonal dipoles. The dipoles are mounted on the outer conductor
of the coaxial line. A unique technique is developed to generate
reconfigurable circular polarization using cross dipole configuration.
The sub-reflector is supported by the feed line, thus requiring no
extra support. The antenna is developed on elliptical ground plane
with dielectric rim making antenna compact. It is demonstrated that
cross dipole excited short backfire antenna can achieve voltage
standing wave ratio (VSWR) bandwidth of 14.28% for 2:1 VSWR,
axial ratio of 0.2 dB with axial ratio (≤ 3dB) bandwidth of 2.14% and
a gain of more than 12 dBi. The experimental results for the designed
antenna structure are in close agreement with computer simulations.
Digital Article Identifier (DOI):
98
4675
Hydrodynamic Characteristics of Dry Beneficiation of Iron Ore and Coal in a Fast Fluidized Bed
Abstract: Iron ore and coal are the two major important raw
materials being used in Iron making industries. Usually ore fines
containing around 5% Alumina are rejected due to higher proportion
of alumina. Therefore, a technology or process which may reduce
the alumina content by 2% by beneficiation process will be highly
attractive . In addition fine coals with ash content is used nearly 12%
is directly injected in blast furnace. Fast fluidization is a technology
by using dry beneficiation of coal and iron ore can be done. During
the fluidization process the iron ore band coal is fluidized at high
velocity in the riser of a fast fluidized bed, the heavier and coarse
particles is generally settled at the bottom in a dense zone of the riser
while the finer and lighter particle are entrained to the top dilute zone
and then via a cyclone is fed back to the bottom of the riser column.
Most of the alumina and low ash fine size coals being lighter are
expected to move up to the riser and by a natural beneficiation of
ores is expected to take place in the riser. Therefore in this study an
attempt has been made for dry beneficiation of iron ore and coal in a
fluidized bed and its hydrodynamic characterization.
Digital Article Identifier (DOI):
97
8140
Pseudo-Homogeneous Kinetic of Dilute-Acid Hydrolysis of Rice Huskfor Ethanol Production: Effect of Sugar Degradation
Abstract: Rice husk is a lignocellulosic source that can be
converted to ethanol. Three hundreds grams of rice husk was mixed
with 1 L of 0.18 N sulfuric acid solutions then was heated in an
autoclave. The reaction was expected to be at constant temperature
(isothermal), but before that temperature was achieved, reaction has
occurred. The first liquid sample was taken at temperature of 140 0C
and repeated every 5 minute interval. So the data obtained are in the
regions of non-isothermal and isothermal. It was observed that the
degradation has significant effects on the ethanol production. The
kinetic constants can be expressed by Arrhenius equation with the
frequency factors for hydrolysis and sugar degradation of 1.58 x 105
min-1 and 2.29 x 108 L/mole-min, respectively, while the activation
energies are 64,350 J/mole and 76,571 J/mole. The highest ethanol
concentration from fermentation is 1.13% v/v, attained at 220 0C.
Digital Article Identifier (DOI):
96
13741
Chaos-based Secure Communication via Continuous Variable Structure Control
Abstract: The design of chaos-based secure communication
via synchronized modified Chua-s systems is investigated in
this paper. A continuous control law is proposed to ensure
synchronization of the master and slave modified Chua-s
systems by using the variable structure control technique.
Particularly, the concept of extended systems is introduced
such that a continuous control input is obtained to avoid
chattering phenomenon. Then, it becomes possible to ensure
that the message signal embedded in the transmitter can be
recovered in the receiver.
Digital Article Identifier (DOI):
95
9179
Internal Loading Distribution in Statically Loaded Ball Bearings Subjected to a Centric Thrust Load: Alternative Approach
Abstract: An alternative iterative computational procedure is
proposed for internal normal ball loads calculation in statically
loaded single-row, angular-contact ball bearings, subjected to a
known thrust load, which is applied in the inner ring at the geometric
bearing center line. An accurate method for curvature radii at
contacts with inner and outer raceways in the direction of the motion
is used. Numerical aspects of the iterative procedure are discussed.
Numerical examples results for a 218 angular-contact ball bearing
have been compared with those from the literature. Twenty figures
are presented showing the geometrical features, the behavior of the
convergence variables and the following parameters as functions of
the thrust load: normal ball loads, contact angle, distance between
curvature centers, and normal ball and axial deflections.
Digital Article Identifier (DOI):
94
24
Quantitative Genetics Researches on Milk Protein Systems of Romanian Grey Steppe Breed
Abstract: The paper makes part from a complex research project
on Romanian Grey Steppe, a unique breed in terms of biological and
cultural-historical importance, on the verge of extinction and which
has been included in a preservation programme of genetic resources
from Romania. The study of genetic polymorphism of protean
fractions, especially kappa-casein, and the genotype relations of
these lactoproteins with some quantitative and qualitative features of
milk yield represents a current theme and a novelty for this breed. In
the estimation of the genetic parameters we used R.E.M.L.
(Restricted Maximum Likelihood) method.
The main lactoprotein from milk, kappa - casein (K-cz),
characterized in the specialized literature as a feature having a high
degree of hereditary transmission, behaves as such in the nucleus under
study, a value also confirmed by the heritability coefficient (h2 = 0.57
%). We must mention the medium values for milk and fat quantity
(h2=0.26, 0.29 %) and the fat and protein percentage from milk
having a high hereditary influence h2 = 0.71 - 0.63 %.
Correlations between kappa-casein and the milk quantity are
negative and strong. Between kappa-casein and other qualitative
features of milk (fat content 0.58-0.67 % and protein content 0.77-
0.87%), there are positive and very strong correlations. At the same
time, between kappa-casein and β casein (β-cz), β lactoglobulin (β-
lg) respectively, correlations are positive having high values (0.37 –
0.45 %), indicating the same causes and determining factors for the
two groups of features.
Digital Article Identifier (DOI):
93
14961
Space-Vector PWM Inverter Feeding a Permanent-Magnet Synchronous Motor
Abstract: The paper presents a space-vector pulse width modulation (SVPWM) inverter feeding a permanent-magnet synchronous motor (PMSM). The SVPWM inverter enables to feed the motor with a higher voltage with low harmonic distortions than the conventional sinusoidal PWM inverter. The control strategy of the inverter is the voltage / frequency control method, which is based on the space-vector modulation technique. The proposed PMSM drive system involving the field-oriented control scheme not only decouples the torque and flux which provides faster response but also makes the control task easy. The performance of the proposed drive is simulated. The advantages of the proposed drive are confirmed by the simulation results.
Digital Article Identifier (DOI):
92
1759
Numerical Simulation of Heat Transfer in Primary Surface with Corrugations Recuperators
Abstract: Study fluid flow and heat transfer characteristics of
microchannel in a primary Cross-corrugated(CC) surface recuperators
with corrugations and without corrugations, using CFD method. The
pitch-over-height ratios P/H of Cross-corrugated (CC) surface is from
1.5 to 4.0, included angles β=75º. The study was performed using CFD
software FLUENT to create unit model and simulate fluid
temperature, velocity, heat transfer coefficient and other parameters.
The results from these simulations were compared to experimental
data. It is concluded that, when the Reynolds number is constant, if
increase P/H, j/f will decrease, also the decreasing trend will become
weak. Under the condition of P/H=2.2, if increase the inlet velocity j/f
will decrease; in addition, the heat transfer performance in surface
with corrugation will increase 10% compared to that without
corrugation. The study results can provide the basis to optimize the
design, select the type of heat transfer surface, the scale structure, and
heat-transfer surface arrangement for recuperators.
Digital Article Identifier (DOI):
91
13727
Numerical Simulation of Flow Field in a Elliptic Bottom Stirred Tank with Bottom Baffles
Abstract: When the crisscross baffles and logarithmic spiral
baffles are placed on the bottom of the stirred tank with elliptic
bottom, using CFD software FLUENT simulates the velocity field of
the stirred tank with elliptic bottom and bottom baffles. Compare the
velocity field of stirred tank with bottom crisscross baffle to the
velocity field of stirred tank without bottom baffle and analysis the
flow pattern on the same axis-section and different cross-sections. The
sizes of the axial and radial velocity are compared respectively when
the stirred tank with bottom crisscross baffles, bottom logarithmic
spiral baffles and without bottom baffle. At the same time, the
numerical calculations of mixing power are compared when the stirred
tank with bottom crisscross baffles and bottom logarithmic spiral
baffles. Research shows that bottom crisscross baffles and logarithmic
spiral baffles have a great impact on flow pattern within the reactor
and improve the mixing effect better than without baffle. It also has
shown that bottom logarithmic spiral baffles has lower power
consumption than bottom crisscross baffles.
Digital Article Identifier (DOI):
90
8719
Image Segmentation Using the K-means Algorithm for Texture Features
Abstract: This study aims to segment objects using the K-means
algorithm for texture features. Firstly, the algorithm transforms color
images into gray images. This paper describes a novel technique for
the extraction of texture features in an image. Then, in a group of
similar features, objects and backgrounds are differentiated by using
the K-means algorithm. Finally, this paper proposes a new object
segmentation algorithm using the morphological technique. The
experiments described include the segmentation of single and multiple
objects featured in this paper. The region of an object can be
accurately segmented out. The results can help to perform image
retrieval and analyze features of an object, as are shown in this paper.
Digital Article Identifier (DOI):
89
9253
Observer Design for Chaos Synchronization of Time-delayed Power Systems
Abstract: The global chaos synchronization for a class of time-delayed power systems is investigated via observer-based approach. By employing the concepts of quadratic stability theory and generalized system model, a new sufficient criterion for constructing an observer is deduced. In contrast to the previous works, this paper proposes a theoretical and systematic design procedure to realize chaos synchronization for master-slave power systems. Finally, an illustrative example is given to show the applicability of the obtained scheme.
Digital Article Identifier (DOI):
88
11946
The Impact of Product Package Information on Consumer Behavior toward Genetically Modified Foods
Abstract: Genetically modified (GM) technology in food
production continued to generate controversies. Consumers were
concerned with the GM foods about the healthy and environmental
risks. While consumers- acceptance was a critical factor affecting how
widely this technology be used. According to the research review,
consumers- lack of information was one of the reasons to explain
consumers- low acceptance toward GM foods. The objective for this
study wanted to find out would informative product package affect
consumers- behavior toward GM foods. An experiment was designed
to investigate consumer behavior toward different product package
information. The results indicated that the product package
information influenced consumer product trust toward GM foods.
Compared with the traceability production system information, the
information about the GM rice was approved by authorized
organizations could increase consumers product trust in GM foods.
Consumers in Taiwan saw the information provided by authorized
organizations more credible than other information.
Digital Article Identifier (DOI):
87
3613
Atrial Fibrillation Analysis Based on Blind Source Separation in 12-lead ECG
Abstract: Atrial Fibrillation is the most common sustained
arrhythmia encountered by clinicians. Because of the invisible
waveform of atrial fibrillation in atrial activation for human, it is
necessary to develop an automatic diagnosis system. 12-Lead ECG
now is available in hospital and is appropriate for using Independent
Component Analysis to estimate the AA period. In this research, we
also adopt a second-order blind identification approach to transform
the sources extracted by ICA to more precise signal and then we use
frequency domain algorithm to do the classification. In experiment,
we gather a significant result of clinical data.
Digital Article Identifier (DOI):
86
675
Computer-based Alarm Processing and Presentation Methods in Nuclear Power Plants
Abstract: Computerized alarm systems have been applied
increasingly to nuclear power plants. For existing plants, an add-on
computer alarm system is often installed to the control rooms. Alarm
avalanches during the plant transients are major problems with the
alarm systems in nuclear power plants. Computerized alarm systems
can process alarms to reduce the number of alarms during the plant
transients. This paper describes various alarm processing methods, an
alarm cause tracking function, and various alarm presentation schemes
to show alarm information to the operators effectively which are
considered during the development of several computerized alarm
systems for Korean nuclear power plants and are found to be helpful to
the operators.
Digital Article Identifier (DOI):
85
8376
Lightning Protection Systems Design for Substations by Using Masts and Matlab
Abstract: The economical criterion is accounted as the objective
function to develop a computer program for designing lightning
protection systems for substations by using masts and Matlab in this
work. Masts are needed to be placed at desired locations; the program
will then show mast heights whose sum is the smallest, i.e. satisfies
the economical criterion. The program is helpful for engineers to
quickly design a lightning protection system for a substation. To
realize this work, methodology and limited conditions of the program,
as well as an example of the program result, were described in this
paper.
Digital Article Identifier (DOI):
84
9548
Comparison and Analysis of Lithium Bromide-water Absorption Chillers Using Plastic Heat Transfer Tubes and Traditional Lithium Bromide-water Absorption Chillers
Abstract: There are extensive applications of lithium
bromide-water absorption chillers in industry, but the heat exchangers
corrosion and refrigerating capacity loss are very difficult to be solved.
In this paper, an experiment was conducted by using plastic heat
transfer tubes instead of copper tubes. As an example, for a lithium
bromide-water absorption chiller of refrigerating capacity of 35kW,
the correlative performance of the lithium bromide-water absorption
chiller using plastic heat transfer tubes was compared with the
traditional lithium bromide-water absorption chiller. And then the
following three aspects, i.e., heat transfer area, pipe resistance, and
safety strength, are analyzed. The results show that plastic heat
transfer tubes can be used on lithium bromide-water absorption
chillers, and its prospect is very optimistic.
Digital Article Identifier (DOI):
83
7755
Conservation Techniques for Soil Erosion Control in Tobacco-Based Farming System at Steep Land Areas of Progo Hulu Subwatershed, Central Java, Indonesia
Abstract: This research was aimed at determining the impact of conservation techniques including bench terrace, stone terrace, mulching, grass strip and intercropping on soil erosion at tobacco-based farming system at Progo Hulu subwatershed, Central Java, Indonesia. Research was conducted from September 2007 to September 2009, located at Progo Hulu subwatershed, Central Java, Indonesia. Research site divided into 27 land units, and experimental fields were grouped based on the soil type and slope, ie: 30%, 45% and 70%, with the following treatments: 1) ST0= stone terrace (control); 2) ST1= stone terrace + Setaria spacelata grass strip on a 5 cm height dike at terrace lips + tobacco stem mulch with dose of 50% (7 ton/ ha); 3) ST2= stone terrace + Setaria spacelata grass strip on a 5 cm height dike at terrace lips + tobacco stem mulch with dose of 100% (14 ton/ ha); 4) ST3= stone terrace + tobacco and red bean intercropping + tobacco stem mulch with dose of 50% (7 ton/ ha). 5) BT0= bench terrace (control); 6) BT1= bench terrace + Setaria spacelata grass strip at terrace lips + tobacco stem mulch with dose of 50% (7 ton/ ha); 7) BT2= bench terrace + Setaria spacelata grass strip at terrace lips + tobacco stem mulch with dose of 100% (14 ton/ ha); 8) BT3= bench terrace + tobacco and red bean intercropping + tobacco stem mulch with dose of 50% (7 ton/ ha). The results showed that the actual erosion rates of research site were higher than that of tolerance erosion with mean value 89.08 ton/ha/year and 33.40 ton/ha/year, respectively. These resulted in 69% of total research site (5,119.15 ha) highly degraded. Conservation technique of ST2 was the most effective in suppressing soil erosion, by 42.87%, following with BT2 as much 30.63%. Others suppressed erosion only less than 21%.
Digital Article Identifier (DOI):
82
12617
Fractal Patterns for Power Quality Detection Using Color Relational Analysis Based Classifier
Abstract: This paper proposes fractal patterns for power quality
(PQ) detection using color relational analysis (CRA) based classifier.
Iterated function system (IFS) uses the non-linear interpolation in the
map and uses similarity maps to construct various fractal patterns of
power quality disturbances, including harmonics, voltage sag, voltage
swell, voltage sag involving harmonics, voltage swell involving
harmonics, and voltage interruption. The non-linear interpolation
functions (NIFs) with fractal dimension (FD) make fractal patterns
more distinguishing between normal and abnormal voltage signals.
The classifier based on CRA discriminates the disturbance events in a
power system. Compared with the wavelet neural networks, the test
results will show accurate discrimination, good robustness, and faster
processing time for detecting disturbing events.
Digital Article Identifier (DOI):
81
13160
Parameter Selections of Fuzzy C-Means Based on Robust Analysis
Abstract: The weighting exponent m is called the fuzzifier that
can have influence on the clustering performance of fuzzy c-means
(FCM) and mÎ[1.5,2.5] is suggested by Pal and Bezdek [13]. In this
paper, we will discuss the robust properties of FCM and show that the
parameter m will have influence on the robustness of FCM. According
to our analysis, we find that a large m value will make FCM more
robust to noise and outliers. However, if m is larger than the theoretical
upper bound proposed by Yu et al. [14], the sample mean will become
the unique optimizer. Here, we suggest to implement the FCM
algorithm with mÎ[1.5,4] under the restriction when m is smaller
than the theoretical upper bound.
Digital Article Identifier (DOI):
80
14701
Effect of Different Methods of Soil Fertility on Grain Yield and Chickpea Quality
Abstract: In order to evaluation the effects of natural, biological
and chemical fertilizers on grain yield and chickpea quality, field
experiments were carried out in 2007 and 2008 growing seasons. In
this research the effects of different organic, chemical and biological
fertilizers were investigated on grain yield and quality of chickpea.
Experimental units were arranged in split-split plots based on
randomized complete blocks with three replications. The highest
amounts of yield and yield components were obtained in G1×N5
interaction. Significant increasing of N, P, K, Fe and Mg content in
leaves and grains emphasized on superiority of mentioned treatment
because each one of these nutrients has an approved role in
chlorophyll synthesis and photosynthesis ability of the crop. The
combined application of compost, farmyard manure and chemical
phosphorus (N5) had the best grain quality due to high protein, starch
and total sugar contents, low crude fiber and reduced cooking time.
Digital Article Identifier (DOI):
79
1129
Risk of Late Payment in the Malaysian Construction Industry
Abstract: The purpose of this study is to identify the underlying
causes of late payment from the contractors- perspective in the
Malaysian construction industry and to recommend effective solutions
to mitigate late payment problems. The target groups of respondents in
this study were Grades G3, G5, G6 and G7 contractors with
specialization in building works and civil engineering works registered
with the Construction Industry Development Board (CIDB) in
Malaysia. Results from this study were analyzed with Statistical
Package for the Social Science (SPSS 15.0). From this study, it was
found that respondents have highest ranked five significant variables
out of a total of forty-one variables which can caused late payment
problems: a) cash flow problems due to deficiencies in client-s
management capacity (mean = 3.96); b) client-s ineffective utilization
of funds (mean = 3.88); c) scarcity of capital to finance the project
(mean = 3.81); d) clients failure to generate income from bank when
sales of houses do not hit the targeted amount (mean=3.72); and e)
poor cash flow because of lack of proper process implementation,
delay in releasing of the retention monies to contractor and delay in the
evaluation and certification of interim and final payment (mean =
3.66).
Digital Article Identifier (DOI):
78
5420
Application of Natural Clay to Formulate Nontraditional Completion Fluid that Triples Oil Productivity
Abstract: In the last decades, the problem of perforation
damage has been considered as the major factor for the
reduction of oil productivity. Underbalance perforation is
considered as one of the best means to minimize or overcome
this problem. By maintaining wellbore pressure lower than
formation pressure, perforation damage could be minimize or
eliminated. This can be achieved by the use of nontraditional
lightweight completion fluid. This paper presents the effect of
natural clay in formulating nontraditional completion fluid to
ensure successful perforation job and increase of production
rate. Natural clay is used as homogenizing agent to create a
stable and non-damaging low-density completion fluid.
Results indicate that the addition of natural clay dramatically
increase the stability of the final fluids. In addition, field test
has shown that the application of nontraditional completion
fluid increases oil production by three folds.
Digital Article Identifier (DOI):
77
14483
Esterification of Free Fatty Acids in Crude Palm Oil with Sulfated Zirconia: Effect of Calcination Temperature
Abstract: The production of biodiesel from crude palm oil with
a homogeneous base catalyst is unlikely owing to considerable
formation of soap. Free fatty acids (FFA) in crude palm oil need to
be reduced, e.g. by esterification. This study investigated the activity
of sulfated zirconia calcined at various temperatures for esterification
of FFA in crude palm oil to biodiesel. It was found that under a
proper reaction condition, sulfated zirconia well catalyzes
esterification. FFA content can be reduced to an acceptable value for
typical biodiesel production with a homogeneous base catalyst.
Crystallinity and sulfate attachment of sulfated zirconia depend on
calcination temperature during the catalyst preparation. Too low
temperature of calcination gives amorphous sulfated zirconia which
has low activity for esterification of FFA. In contrast, very high
temperature of calcination removes sulfate group, consequently,
conversion of FFA is reduced. The appropriate temperature range of
calcination is 550-650 oC.
Digital Article Identifier (DOI):
76
4914
Estimation of Production Function in Fishery on the Coasts of Caspian Sea
Abstract: This research was conducted for the first time at the
southeastern coasts of the Caspian Sea in order to evaluate the
performance of osteichthyes cooperatives through production (catch)
function. Using one of the indirect valuation methods in this research,
contributory factors in catch were identified and were inserted into
the function as independent variables. In order to carry out this
research, the performance of 25 Osteichthyes catching cooperatives
in the utilization year of 2009 which were involved in fishing in
Miankale wildlife refuge region. The contributory factors in catch
were divided into groups of economic, ecological and biological
factors. In the mentioned function, catch rate of the cooperative were
inserted into as the dependant variable and fourteen partial variables
in terms of nine general variables as independent variables. Finally,
after function estimation, seven variables were rendered significant at
99 percent reliably level. The results of the function estimation
indicated that human resource (fisherman quantity) had the greatest
positive effect on catch rate with an influence coefficient of 1.7 while
weather conditions had the greatest negative effect on the catch rate
of cooperatives with an influence coefficient of -2.07. Moreover,
factors like member's share, experience and fisherman training and
fishing effort played the main roles in the catch rate of cooperative
with influence coefficients of 0.81, 0.5 and 0.21, respectively.
Digital Article Identifier (DOI):
75
8943
Programming Aid Tool for Detecting Common Mistakes of Novice Programmers in OpenMP Code
Abstract: OpenMP is an API for parallel programming model of shared memory multiprocessors. Novice OpenMP programmers often produce the code that compiler cannot find human errors. It was investigated how compiler coped with the common mistakes that can occur in OpenMP code. The latest version(4.4.3) of GCC is used for this research. It was found that GCC compiled the codes without any errors or warnings. In this paper the programming aid tool is presented for OpenMP programs. It can check 12 common mistakes that novice programmer can commit during the programming of OpenMP. It was demonstrated that the programming aid tool can detect the various common mistakes that GCC failed to detect.
Digital Article Identifier (DOI):
74
14620
Deicing and Corrosive Performances of Calcium Acetate Deicer Made from Bamboo-Vinegar
Abstract: Calcium magnesium acetate (CMA) is environmentally
benign deicing chemicals that can replace sodium chloride that is
widely used on roads and highways at present for snow and ice control
to provide safe driving conditions during winter. The price of CMA
from petroleum-derived acetic acid is quite expensive. The bamboo
vinegar is the by-product from bamboo charcoal production. The
bamboo vinegar was used to prepare calcium acetate as raw materials,
and its deicing and corrosive performances were studied in this paper.
The results show that the freezing temperature of calcium acetate is
lower than that of sodium chloride when they have same molar
concentration, the deicing performance of calcium acetate is better
than that of sodium chloride when they have same moles, while the
deicing performance of sodium chloride is better than that of calcium
acetate. The corrosion of sodium chloride on iron-nail and steel-nail is
larger than that of calcium acetate whether they have same mass
concentration or same molar concentration, and the corrosion of
sodium chloride and calcium acetate on iron-nail is larger than that on
steel-nail, and calcium acetate almost hasn't corrosion on steel-nail.
Digital Article Identifier (DOI):
73
14211
Design of Buffer Management for Industry to Avoid Sensor Data- Conflicts
Abstract: To reduce accidents in the industry, WSNs(Wireless Sensor
networks)- sensor data is used. WSNs- sensor data has the persistence and
continuity. therefore, we design and exploit the buffer management system that
has the persistence and continuity to avoid and delivery data conflicts. To
develop modules, we use the multi buffers and design the buffer management
modules that transfer sensor data through the context-aware methods.
Digital Article Identifier (DOI):
72
1621
Color Shift of Printing with Hybrid Halftone Images for Overlay Misalignment
Abstract: Color printing proceeds with multiple halftone
separations overlay. Because of separation overlay misalignment in
printing, the percentage of different primary color combination may
vary and it will result in color shift. In traditional printing procedure
with AM halftone, every separation has different screening angle to
make the superposition pattern in a random style, which will reduce
the color shift. To evaluate the color shift of printing with hybrid
halftoning, we simulate printing procedure with halftone images
overlay and calculate the color difference between expected color and
color in different overlay misalignment configurations. The color
difference for hybrid halftone and AM halftone is very close. So the
color shift for hybrid halftone is acceptable with current color printing
procedure.
Digital Article Identifier (DOI):
71
121
A Novel Convergence Accelerator for the LMS Adaptive Algorithm
Abstract: The least mean square (LMS) algorithmis one of the
most well-known algorithms for mobile communication systems
due to its implementation simplicity. However, the main limitation
is its relatively slow convergence rate. In this paper, a booster
using the concept of Markov chains is proposed to speed up the
convergence rate of LMS algorithms. The nature of Markov
chains makes it possible to exploit the past information in the
updating process. Moreover, since the transition matrix has a
smaller variance than that of the weight itself by the central limit
theorem, the weight transition matrix converges faster than the
weight itself. Accordingly, the proposed Markov-chain based
booster thus has the ability to track variations in signal
characteristics, and meanwhile, it can accelerate the rate of
convergence for LMS algorithms. Simulation results show that the
LMS algorithm can effectively increase the convergence rate and
meantime further approach the Wiener solution, if the
Markov-chain based booster is applied. The mean square error is
also remarkably reduced, while the convergence rate is improved.
Digital Article Identifier (DOI):
70
878
Emotion Classification by Incremental Association Language Features
Abstract: The Major Depressive Disorder has been a burden of
medical expense in Taiwan as well as the situation around the world.
Major Depressive Disorder can be defined into different categories by
previous human activities. According to machine learning, we can
classify emotion in correct textual language in advance. It can help
medical diagnosis to recognize the variance in Major Depressive
Disorder automatically. Association language incremental is the
characteristic and relationship that can discovery words in sentence.
There is an overlapping-category problem for classification. In this
paper, we would like to improve the performance in classification in
principle of no overlapping-category problems. We present an
approach that to discovery words in sentence and it can find in high
frequency in the same time and can-t overlap in each category, called
Association Language Features by its Category (ALFC).
Experimental results show that ALFC distinguish well in Major
Depressive Disorder and have better performance. We also compare
the approach with baseline and mutual information that use single
words alone or correlation measure.
Digital Article Identifier (DOI):
69
6918
Evaluation of the Immunoregulatory Activity of rFip-gts Purified from Baculovirus-infected Insect Cells
Abstract: Fip-gts, an immunomodulatory protein purified from Ganoderma tsugae, has been reported to possess therapeutic effects in the treatment of cancer and autoimmune disease. For medicinal application, a recombinant Fip-gts was successfully expressed and purified in Sf21 insect cells by our previously work. It is important to evaluate the immunomodulatory activity of the rFip-gts. To assess the immunomodulatory potential of rFip-gts, the T lymphocytes of murine splenocytes were used in the present study. Results revealed that rFip-gts induced cellular aggregation formation. Additionally, the expression of IL-2 and IFN-r were up-regulated after the treatment of rFip-gts, and a corresponding increased production of IL-2 and IFN-r in a dose-dependent manner. The results showed that rFip-gts has an immunomodulatory activity in inducing Th1 lymphocytes from murine splenocytes released IL-2 and IFN-γ, thus suggest that rFip-gts may have therapeutic potential in vivo as an immune modulator.
Digital Article Identifier (DOI):
68
9100
Effects of Temperature-Dependent Material Properties on Stress and Temperature in Cracked Metal Plate under Electric Current Load
Abstract: Using the finite element analyses, this paper discusses the effects of temperature-dependent material properties on the stress and temperature fields in a cracked metal plate under the electric current load. The practical and complicated results are obtained when the temperature-dependent material properties are adopted in the analysis. If the simplified (temperature-independent) material properties are used, incorrect results will be obtained.
Digital Article Identifier (DOI):
67
14066
Influence of Static Pressure on Viability of Entomopathogenic Nematodes – Steinernema feltiae
Abstract: The entomopathogenic nematodes Steinernema
feltiaeare are components of many biological pesticides. The
biological pesticides are applicated by means a spraying machines.
The influence of high pressure operating time on viability of
nematodes has been experimentally investigated in order to explain if
static pressure inside of the sprayers installation was able to destroy
nematodes. The value of pressure was 55 MPa and its maximum
operating time was 3 hours. Changes were found in viability of
pressurized samples of nematodes, mixed with water.
Digital Article Identifier (DOI):
66
13309
Artificial Visual Percepts for Image Understanding
Abstract: Visual inputs are one of the key sources from which
humans perceive the environment and 'understand' what is
happening. Artificial systems perceive the visual inputs as digital
images. The images need to be processed and analysed. Within the
human brain, processing of visual inputs and subsequent
development of perception is one of its major functionalities. In this
paper we present part of our research project, which aims at the
development of an artificial model for visual perception (or
'understanding') based on the human perceptive and cognitive
systems. We propose a new model for perception from visual inputs
and a way of understaning or interpreting images using the model.
We demonstrate the implementation and use of the model with a real
image data set.
Digital Article Identifier (DOI):
65
6501
Supply Chain Management and E-Commerce Technology Adoption among Logistics Service Providers in Malaysia
Abstract: Logistics is part of the supply chain processes that
plans, implements, and controls the efficient and effective forward
and reverse flow and storage of goods, services, and related
information between the point of origin and the point of consumption
in order to meet customer requirements. This research aims to
investigate the current status and future direction of the use of
Information Technology (IT) for logistics, focusing on Supply Chain
Management (SCM) and E-Commerce adoption in Malaysia.
Therefore, this research stresses on the type of technology being
adopted, factors, benefits and barriers affecting the innovation in
SCM and E-Commerce technology adoption among Logistics
Service Providers (LSP). A mailed questionnaire survey was
conducted to collect data from 265 logistics companies in Johor. The
research revealed a high level of SCM technology adoption among
LSP as they had adopted SCM technology in various business
processes while they perceived a high level of benefits from SCM
adoption.
Digital Article Identifier (DOI):
64
9399
Certain Estimates of Oscillatory Integrals and Extrapolation
Abstract: In this paper we study the boundedness properties of
certain oscillatory integrals with polynomial phase. We obtain sharp
estimates for these oscillatory integrals. By the virtue of these
estimates and extrapolation we obtain Lp boundedness for these
oscillatory integrals under rather weak size conditions on the kernel
function.
Digital Article Identifier (DOI):
63
4377
Enhancing Human-Computer Interaction and Feedback in Touchscreen Icon
Abstract: In order to enhance the usability of the human computer interface (HCI) on the touchscreen, this study explored the optimal tactile depth and effect of visual cues on the user-s tendency to touch the touchscreen icons. The experimental program was designed on the touchscreen in this study. Results indicated that the ratio of the icon size to the tactile depth was 1:0.106. There were significant effects of experienced users and novices on the tactile feedback depth (p < 0.01). In addition, the results proved that the visual cues provided a feedback that helped to guide the user-s touch icons accurately and increased the capture efficiency for a tactile recognition field. This tactile recognition field was 18.6 mm in length. There was consistency between the experienced users and novices under the visual cue effects. Finally, the study developed an applied design with touch feedback for touchscreen icons.
Digital Article Identifier (DOI):
62
15807
High Efficiency, Selectivity against Cancer Cell Line of Purified L-Asparaginase from Pathogenic Escherichia coli
Abstract: L-asparaginase was extracted from pathogenic
Escherichia coli which was isolated from urinary tract infection
patients. L-asparaginase was purified 96-fold by ultrafiltration, ion
exchange and gel filtration giving 39.19% yield with final specific
activity of 178.57 IU/mg. L-asparaginase showed 138,356±1,000
Dalton molecular weight with 31024±100 Dalton molecular mass.
Kinetic properties of enzyme resulting 1.25×10-5 mM Km and
2.5×10-3 M/min Vmax. L-asparaginase showed a maximum activity
at pH 7.5 when incubated at 37 ºC for 30 min and illustrated its full
activity (100%) after 15 min incubation at 20-37 ºC, while 70% of its
activity was lost when incubated at 60 ºC. L-asparaginase showed
cytotoxicity to U937 cell line with IC50 0.5±0.19 IU/ml, and
selectivity index (SI=7.6) about 8 time higher selectivity over the
lymphocyte cells. Therefore, the local pathogenic E. coli strains may
be used as a source of high yield of L-asparaginase to produce anti
cancer agent with high selectivity.
Digital Article Identifier (DOI):
61
15804
Denial of Service (DOS) Attack and Its Possible Solutions in VANET
Abstract: Vehicular Ad-hoc Network (VANET) is taking more
attention in automotive industry due to the safety concern of human
lives on roads. Security is one of the safety aspects in VANET. To be
secure, network availability must be obtained at all times since
availability of the network is critically needed when a node sends any
life critical information to other nodes. However, it can be expected
that security attacks are likely to increase in the coming future due to
more and more wireless applications being developed and deployed
onto the well-known expose nature of the wireless medium. In this
respect, the network availability is exposed to many types of attacks.
In this paper, Denial of Service (DOS) attack on network availability
is presented and its severity level in VANET environment is
elaborated. A model to secure the VANET from the DOS attacks has
been developed and some possible solutions to overcome the attacks
have been discussed.
Digital Article Identifier (DOI):
60
14847
Controlled Assembly of Magnetic Biomolecular Nanostructures
Abstract: Two optimized strategies were successfully established
to develop biomolecule-based magnetic nanoassemblies.
Streptavidin-coated and amine-coated magnetic nanoparticles were
chosen as model scaffolds onto which double-stranded DNA and
human immunoglobulin G were specifically conjugated in succession,
using biotin-streptavidin interaction or covalent cross-linkers. The
success of this study opens the prospect of developing selective and
sensitive nanoparticle-based structures for diagnostics or drug
delivery.
Digital Article Identifier (DOI):
59
6136
Variable Guard Channels for Efficient Traffic Management
Abstract: Guard channels improve the probability of successful
handoffs by reserving a number of channels exclusively for handoffs.
This concept has the risk of underutilization of radio spectrum due to
the fact that fewer channels are granted to originating calls even if
these guard channels are not always used, when originating calls are
starving for the want of channels. The penalty is the reduction of
total carried traffic. The optimum number of guard channels can help
reduce this problem. This paper presents fuzzy logic based guard
channel scheme wherein guard channels are reorganized on the basis
of traffic density, so that guard channels are provided on need basis.
This will help in incorporating more originating calls and hence high
throughput of the radio spectrum
Digital Article Identifier (DOI):
58
284
Water and Soil Environment Pollution Reduction by Filter Strips
Abstract: Contour filter strips planted with perennial vegetation
can be used to improve surface and ground water quality by reducing
pollutant, such as NO3-N, and sediment outflow from cropland to a
river or lake. Meanwhile, the filter strips of perennial grass with biofuel
potentials also have economic benefits of producing ethanol. In
this study, The Soil and Water Assessment Tool (SWAT) model was
applied to the Walnut Creek Watershed to examine the effectiveness
of contour strips in reducing NO3-N outflows from crop fields to the
river or lake. Required input data include watershed topography,
slope, soil type, land-use, management practices in the watershed and
climate parameters (precipitation, maximum/minimum air
temperature, solar radiation, wind speed and relative humidity).
Numerical experiments were conducted to identify potential
subbasins in the watershed that have high water quality impact, and
to examine the effects of strip size and location on NO3-N reduction
in the subbasins under various meteorological conditions (dry,
average and wet). Variable sizes of contour strips (10%, 20%, 30%
and 50%, respectively, of a subbasin area) planted with perennial
switchgrass were selected for simulating the effects of strip size and
location on stream water quality. Simulation results showed that a
filter strip having 10%-50% of the subbasin area could lead to 55%-
90% NO3-N reduction in the subbasin during an average rainfall
year. Strips occupying 10-20% of the subbasin area were found to be
more efficient in reducing NO3-N when placed along the contour
than that when placed along the river. The results of this study can
assist in cost-benefit analysis and decision-making in best water
resources management practices for environmental protection.
Digital Article Identifier (DOI):
57
4135
Absorption Center of Photophoresis with in Micro-Sized and Spheroidal Particles in a Gaseous Medium
Abstract: The present study is concerned with the absorption
center of photophoresis within a micro-sized and spheroidal particle in
a gaseous medium. A particle subjected to an intense light beam can
absorb electromagnetic energy within the particle unevenly, which
results in photophoretic force to drive the particle in motion. By
evaluating the energy distribution systematically at various conditions,
the study focuses on the effects of governing parameters, such as
particle aspect ratio, size parameter, refractivity, and absorptivity, on
the heat source function within the particle and their potential
influences to the photophoresis.
Digital Article Identifier (DOI):
56
13325
Three Computational Mathematics Techniques: Comparative Determination of Area under Curve
Abstract: The objective of this manuscript is to find area under the plasma concentration- time curve (AUC) for multiple doses of salbutamol sulphate sustained release tablets (Ventolin® oral tablets SR 8 mg, GSK, Pakistan) in the group of 18 healthy adults by using computational mathematics techniques. Following the administration of 4 doses of Ventolin® tablets 12 hourly to 24 healthy human subjects and bioanalysis of obtained plasma samples, plasma drug concentration-time profile was constructed. AUC, an important pharmacokinetic parameter, was measured using integrated equation of multiple oral dose regimens. The approximated AUC was also calculated by using computational mathematics techniques such as repeated rectangular, repeated trapezium and repeated Simpson's rule and compared with exact value of AUC calculated by using integrated equation of multiple oral dose regimens to find best computational mathematics method that gives AUC values closest to exact. The exact values of AUC for four consecutive doses of Ventolin® oral tablets were 150.5819473, 157.8131756, 164.4178231 and 162.78 ng.h/ml while the closest values approximated AUC values were 149.245962, 157.336171, 164.2585768 and 162.289224 ng.h/ml, respectively as found by repeated rectangular rule. The errors in the approximated values of AUC were negligible. It is concluded that all computational tools approximated values of AUC accurately but the repeated rectangular rule gives slightly better approximated values of AUC as compared to repeated trapezium and repeated Simpson's rules.
Digital Article Identifier (DOI):
55
15397
Validation and Application of a New Optimized RP-HPLC-Fluorescent Detection Method for Norfloxacin
Abstract: A new reverse phase-high performance liquid chromatography (RP-HPLC) method with fluorescent detector (FLD) was developed and optimized for Norfloxacin determination in human plasma. Mobile phase specifications, extraction method and excitation and emission wavelengths were varied for optimization. HPLC system contained a reverse phase C18 (5 μm, 4.6 mm×150 mm) column with FLD operated at excitation 330 nm and emission 440 nm. The optimized mobile phase consisted of 14% acetonitrile in buffer solution. The aqueous phase was prepared by mixing 2g of citric acid, 2g sodium acetate and 1 ml of triethylamine in 1 L of Milli-Q water was run at a flow rate of 1.2 mL/min. The standard curve was linear for the range tested (0.156–20 μg/mL) and the coefficient of determination was 0.9978. Aceclofenac sodium was used as internal standard. A detection limit of 0.078 μg/mL was achieved. Run time was set at 10 minutes because retention time of norfloxacin was 0.99 min. which shows the rapidness of this method of analysis. The present assay showed good accuracy, precision and sensitivity for Norfloxacin determination in human plasma with a new internal standard and can be applied pharmacokinetic evaluation of Norfloxacin tablets after oral administration in human.
Digital Article Identifier (DOI):
54
3809
A Bayesian Hierarchical 13COBT to Correct Estimates Associated with a Delayed Gastric Emptying
Abstract: The use of a Bayesian Hierarchical Model (BHM) to interpret breath measurements obtained during a 13C Octanoic Breath Test (13COBT) is demonstrated. The statistical analysis was implemented using WinBUGS, a commercially available computer package for Bayesian inference. A hierarchical setting was adopted where poorly defined parameters associated with a delayed Gastric Emptying (GE) were able to "borrow" strength from global distributions. This is proved to be a sufficient tool to correct model's failures and data inconsistencies apparent in conventional analyses employing a Non-linear least squares technique (NLS). Direct comparison of two parameters describing gastric emptying ng ( tlag -lag phase, t1/ 2 -half emptying time) revealed a strong correlation between the two methods. Despite our large dataset ( n = 164 ), Bayesian modeling was fast and provided a successful fitting for all subjects. On the contrary, NLS failed to return acceptable estimates in cases where GE was delayed.
Digital Article Identifier (DOI):
53
11532
Intelligent Fuzzy Input Estimator for the Input Force on the Rigid Bar Structure System
Abstract: The intelligent fuzzy input estimator is used to estimate
the input force of the rigid bar structural system in this study. The
fuzzy Kalman filter without the input term and the fuzzy weighting
recursive least square estimator are two main portions of this method.
The practicability and accuracy of the proposed method were verified
with numerical simulations from which the input forces of a rigid bar
structural system were estimated from the output responses. In order to
examine the accuracy of the proposed method, a rigid bar structural
system is subjected to periodic sinusoidal dynamic loading. The
excellent performance of this estimator is demonstrated by comparing
it with the use of difference weighting function and improper the
initial process noise covariance. The estimated results have a good
agreement with the true values in all cases tested.
Digital Article Identifier (DOI):
52
10007
Conversion of Sugarcane Shoots to Reducing Sugars
Abstract: Sugarcane Shoots is an abundantly available
residual resources consisting of lignocelluloses which take it into
the benefit. The present study was focused on utilizing of
sugarcane shoot for reducing sugar production as a substrate in
ethanol production. Physical and chemical pretreatments of
sugarcane shoot were investigated. Results showed that the size of
sugarcane shoot influenced the cellulose content. The maximum
cellulose yield (60 %) can be obtained from alkaline pretreated
sugarcane shoot with 1.0 M NaOH at 30 oC for 90 min. The
cellulose yield reached up to 93.9% (w/w). Enzymatically
hydrolyzed of cellulosic residual in 0.04 citrate buffer (pH 5) with
celluclast 1.5L (0.7 FPU/ml) resulted in the highest amount of
reducing sugar at a rate of 32.1 g/l after 4 h incubation at 50°C,
and 100 oC for 5 min . Cellulose conversion was 55.5%.
Digital Article Identifier (DOI):
51
6187
Implementation of a “DIVA“ Concept withspecific Elisa Kits; When Subunit H5 Avian Influenza Vaccine is used
Abstract: The main objective of this study was to demonstrate that differentiation of infected and vaccinated animals (DIVA) strategy using different ELISA tests is possible when a subunit vaccine (Haemagglutinin protein) is used to prevent Avian influenza. Special emphasis was placed on the differentiation in the serological response to different components of the AIV (Nucleoprotein, Neuraminidase, Haemagglutinin, Nucleocapsid) between chickens that were vaccinated with a whole virus kill vaccine and recombinant vaccine. Furthermore, the potential use of this DIVA strategy using ELISA assays to detect Neuraminidase 1 (N1) was analyzed as strategy in countries where the field virus is H5N1 and the vaccine used is formulated with H5N2. Detection of AIV-s antibodies to any component in serum was negative for all animals on the study days 0-13. At study day 14 the titers of antibodies against Nucleoprotein (NP) and Nucleocapsid (NC) rose in the experimental groups vaccinated with Volvac® AI KV and were negatives during all the trial in the experimental groups vaccinated with a subunit H5; significant statistically differences were observed between these groups (p < 0.05). The seroconversion either Haemagglutinin or Neuraminidase was evident after 21 days post-vaccination in the experimental groups vaccinated with the respective viral fraction. Regarding the main aim of this study and according with the results that were obtained, use a combination of different ELISA test as a DIVA strategy is feasible when the vaccination is carry out with a subunit H5 vaccine. Also is possible to use the ELISA kit to detect Neuraminidase (either N1 or N2) as a DIVA concept in countries where H5N1 is present and the vaccination programs are done with H5N2 vaccine.
Digital Article Identifier (DOI):
50
8806
Analysis of the Genetic Sequences of PCV2 Virus in Mexico
Abstract: These All pig-producing countries from around the world report the presence of Postweaning multisystemic wasting syndrome (PMWS.) In America, PCV2 has been recognized in Canada, United States and Brazil. Knowledge concerning the genetic sequences of PMWS has been very important. In Mexico, there is no report describing the genetic sequences and variations of the PCV2 virus present around the country. For this reason, the main objective was to describe the homology and genetic sequences of the PCV2 virus obtained from different regions of Mexico. The results show that in Mexico are present both subgenotypes \"a\" and \"b\" of this virus and the homologies are from 89 to 99%. Regarding with the aminoacid sequence, three major heterogenic regions were present in the position 59-91, 123–136 and 185–210. This study presents the results of the first genetic characterization of PCV2 in production herds from Mexico.
Digital Article Identifier (DOI):
49
1460
Silicone on Blending Vegetal Petrochemical Based Polyurethane
Abstract: Polyurethane foam (PUF) is formed by a chemical
reaction of polyol and isocyanate. The aim is to understand the
impact of Silicone on synthesizing polyurethane in differentiate
volume of molding. The method used was one step process, which is
simultaneously caried out a blending polyol (petroleum polyol and
soybean polyol), a TDI (2,4):MDI (4,4-) (80:20), a distilled water,
and a silicone. The properties of the material were measured via a
number of parameters, which are polymer density, compressive
strength, and cellular structures. It is found that density of
polyurethane using silicone with volume of molding either 250 ml or
500 ml is lower than without using silicone.
Digital Article Identifier (DOI):
48
13434
Justification and Classification of Issues for the Selection and Implementation of Advanced Manufacturing Technologies
Abstract: It has often been said that the strength of any country
resides in the strength of its industrial sector, and Progress in
industrial society has been accomplished by the creation of new
technologies. Developments have been facilitated by the increasing
availability of advanced manufacturing technology (AMT), in
addition the implementation of advanced manufacturing technology
(AMT) requires careful planning at all levels of the organization to
ensure that the implementation will achieve the intended goals.
Justification and implementation of advanced manufacturing
technology (AMT) involves decisions that are crucial for the
practitioners regarding the survival of business in the present days of
uncertain manufacturing world. This paper assists the industrial
managers to consider all the important criteria for success AMT
implementation, when purchasing new technology. Concurrently,
this paper classifies the tangible benefits of a technology that are
evaluated by addressing both cost and time dimensions, and the
intangible benefits are evaluated by addressing technological,
strategic, social and human issues to identify and create awareness of
the essential elements in the AMT implementation process and
identify the necessary actions before implementing AMT.
Digital Article Identifier (DOI):
47
15548
Achieving High Availability by Implementing Beowulf Cluster
Abstract: A computer cluster is a group of tightly coupled
computers that work together closely so that in many respects they
can be viewed as though they are a single computer. The components
of a cluster are commonly, but not always, connected to each other
through fast local area networks. Clusters are usually deployed to
improve performance and/or availability over that provided by a
single computer, while typically being much more cost-effective than
single computers of comparable speed or availability. This paper
proposed the way to implement the Beowulf Cluster in order to
achieve high performance as well as high availability.
Digital Article Identifier (DOI):
46
1041
The Effect of Variable Incubation Temperatures on Hatchability and Survival of Goldlined Seabream, Rhabdosargus sarba (Forsskål,1775) Larvae
Abstract: The effect of varying holding temperature on hatching success, occurrence of deformities and mortality rates were investigated for goldlined seabream eggs. Wild broodstock (600 g) were stocked at a 2:1 male-female ratio in a 2 m3 fiberglass tank supplied with filtered seawater (37 g L-1 salinity, temp. range 24±0.5 oC [day] and 22±1 oC [night], DO2 in excess of 5.0mg L-1). Females were injected with 200 IU kg-1 HCG between 08.00 and 10.00 h and returned to tanks to spawn following which eggs were collected by hand using a 100μm net. Fertilized eggs at the gastrulation stage (120 L-1) were randomly placed into one of 12 experimental 6 L aerated (DO2 5 mg L-1) plastic containers with water temperatures maintained at 24±0.5 oC (ambient), 26±0.5 oC, 28± 0.5 oC and 30±0.5 oC using thermostats. Each treatment was undertaken in triplicate using a 12:12 photophase:scotophase photoperiod. No differences were recorded between eggs reared at 24 and 26 oC with respect to viability, deformity, mortality or unhatched egg rates. Increasing temperature reduced the number of viable eggs with those at 30 oC returning poorest performance (P < 0.05). Mortality levels were lowest for eggs incubated at 24 and 26 oC. The greatest level of deformities recorded was that for eggs reared at 28 oC.
Digital Article Identifier (DOI):
45
8770
Research on Applying the Continuity Care Document to Generate a Medical Record with Entry Level
Abstract: Transferring patient information between medical care
sites is necessary to deliver better patient care and to reduce medical
cost. So developing of electronic medical records is an important trend
for the world.The Continuity of Care Document (CCD) is product of
collaboration between CDA and CCR standards. In this study, we will
develop a system to generate medical records with entry level based on
CCD template module.
Digital Article Identifier (DOI):
44
5863
The Study of Managing the Personal Consent in the Electronic Healthcare Environment
Abstract: The Electronic Health Record (EHR) system is very
general and we should pay more attention to a patient-s privacy. The
patient-s consent is one of the elements when dealing with privacy
topics. This study focuses on the creating and managing of patient
consent. The integration of the HL7 standards and the IHE BPPC
profile provides a base for the creation of patient consent. Establishing
the platform offers the patients a way to create, revoke or update their
consents. Through this platform, they can manage their consents in an
easier manner.
Digital Article Identifier (DOI):
43
14243
Development of Reliable Web-Based Laboratories for Developing Countries
Abstract: In online context, the design and implementation of
effective remote laboratories environment is highly challenging on
account of hardware and software needs. This paper presents the
remote laboratory software framework modified from ilab shared
architecture (ISA). The ISA is a framework which enables students to
remotely acccess and control experimental hardware using internet
infrastructure. The need for remote laboratories came after
experiencing problems imposed by traditional laboratories. Among
them are: the high cost of laboratory equipment, scarcity of space,
scarcity of technical personnel along with the restricted university
budget creates a significant bottleneck on building required
laboratory experiments. The solution to these problems is to build
web-accessible laboratories. Remote laboratories allow students and
educators to interact with real laboratory equipment located
anywhere in the world at anytime. Recently, many universities and
other educational institutions especially in third world countries rely
on simulations because they do not afford the experimental
equipment they require to their students. Remote laboratories enable
users to get real data from real-time hand-on experiments. To
implement many remote laboratories, the system architecture should
be flexible, understandable and easy to implement, so that different
laboratories with different hardware can be deployed easily. The
modifications were made to enable developers to add more
equipment in ISA framework and to attract the new developers to
develop many online laboratories.
Digital Article Identifier (DOI):
42
4096
On Climbing Winding Stairs for a Robotic Wheelchair
Abstract: In this paper motion analysis on a winding
stair-climbing is investigated using our proposed rotational arm type
of robotic wheelchair. For now, the robotic wheelchair is operated in
an open mode to climb winding stairs by a dynamic turning, therefore,
the dynamics model is required to ensure a passenger-s safety.
Equations of motion based on the skid-steering analysis are developed
for the trajectory planning and motion analysis on climbing winding
stairs. Since the robotic wheelchair must climb a winding staircase
stably, the winding trajectory becomes a constraint equation to be
followed, and the Baumgarte-s method is used to solve for the
constrained dynamics equations. Experimental results validate the
behavior of the prototype as it climbs a winding stair.
Digital Article Identifier (DOI):
41
3254
Computations of Bezier Geodesic-like Curves on Spheres
Abstract: It is an important problem to compute the geodesics on
a surface in many fields. To find the geodesics in practice, however,
the traditional discrete algorithms or numerical approaches can only
find a list of discrete points. The first author proposed in 2010 a new,
elegant and accurate method, the geodesic-like method, for
approximating geodesics on a regular surface. This paper will present
by use of this method a computation of the Bezier geodesic-like curves
on spheres.
Digital Article Identifier (DOI):
40
14845
The Distance between a Point and a Bezier Curveon a Bezier Surface
Abstract: The distance between two objects is an important
problem in CAGD, CAD and CG etc. It will be presented in this paper
that a simple and quick method to estimate the distance between a
point and a Bezier curve on a Bezier surface.
Digital Article Identifier (DOI):
39
4639
Genetic Polymorphism of Main Lactoproteins of Romanian Grey Steppe Breed in Preservation
Abstract: The paper presents a part of the results obtained in a
complex research project on Romanian Grey Steppe breed, owner of
some remarkable qualities such as hardiness, longevity, adaptability,
special resistance to ban weather and diseases and included in the
genetic fund (G.D. no. 822/2008.) from Romania.
Following the researches effectuated, we identified alleles of six
loci, codifying the six types of major milk proteins: alpha-casein S1
(α S1-cz); beta-casein (β-cz); kappa-casein (K-cz); beta-lactoglobulin
(β-lg); alpha-lactalbumin (α-la) and alpha-casein S2 (α S2-cz). In
system αS1-cz allele αs1-Cn B has the highest frequency (0.700), in
system β-cz allele β-Cn A2 ( 0.550 ), in system K-cz allele k-CnA2 (
0.583 ) and heterozygote genotype AB ( 0.416 ) and BB (0.375), in
system β-lg allele β-lgA1 has the highest frequency (0.542 ) and
heterozygote genotype AB ( 0.500 ), in system α-la there is
monomorphism for allele α-la B and similarly in system αS2-cz for
allele αs2-Cn A.
The milk analysis by the isoelectric focalization technique (I.E.F.)
allowed the identification of a new allele for locus αS1-casein, for two
of the individuals under analysis, namely allele called αS1-casein
IRV. When experiments were repeated, we noticed that this is not a
proteolysis band and it really was a new allele that has not been
registered in the specialized literature so far. We identified two
heterozygote individuals, carriers of this allele, namely: BIRV and
CIRV. This discovery is extremely important if focus is laid on the
national genetic patrimony.
Digital Article Identifier (DOI):
38
11338
Characteristics of Suspended Solids Removal by Electrocoagulation
Abstract: The electrochemical coagulation of a kaolin
suspension was investigated at the currents of 0.06, 0.12, 0.22, 0.44,
0.85 A (corresponding to 0.68, 1.36, 2.50, 5.00, 9.66 mA·cm-2,
respectively) for the contact time of 5, 10, 20, 30, and 50 min. The
TSS removal efficiency at currents of 0.06 A, 0.12 A and 0.22 A
increased with the amount of iron generated by the sacrificial anode,
while the removal efficiencies did not increase proportionally with
the amount of iron generated at the currents of 0.44 and 0.85 A,
where electroflotation was clearly observed. Zeta potential
measurement illustrated the presence of the highly positive charged
particles created by sorption of highly charged polymeric metal
hydroxyl species onto the negative surface charged kaolin particles at
both low and high applied currents. The disappearance of the
individual peaks after certain contact times indicated the attraction
between these positive and negative charged particles causing
agglomeration. It was concluded that charge neutralization of the
individual species was not the only mechanism operating in the
electrocoagulation process at any current level, but electrostatic
attraction was likely to co-operate or mainly operate.
Digital Article Identifier (DOI):
37
13876
Effects of Formic Acid on the Chemical State and Morphology of As-synthesized and Annealed ZnO Films
Abstract: Zinc oxide thin films with various microstructures
were grown on substrates by using HCOOH-sols. The reaction
mechanism of the sol system was investigated by performing an XPS
analysis of as-synthesized films, due to the products of hydrolysis
and condensation in the sol system contributing to the chemical state
of the as-synthesized films. The chemical structures of the assynthesized
films related to the microstructures of the final annealed
films were also studied. The results of the Zn 2p3/2, C 1s and O1s
XPS patterns indicate that the hydrolysis reaction in the sol system is
strongly influenced by the HCOOH agent. The results of XRD and
FE-SEM demonstrated the microstructures of the annealed films are
related to the content of hydrolyzed zinc hydrate (Zn-OH) species
present, and that content of the Zn-OH species in the sol system
increases the HCOOH adding, and these Zn-OH species existing in
the sol phase are responsible for large ZnO crystallites in the final
annealed films.
Digital Article Identifier (DOI):
36
12255
Arsenate Removal by Nano Zero-valent Iron in the Gas Bubbling System
Abstract: This study focused on arsenate removal by nano
zero-valent iron (NZVI) in the gas-bubbled aqueous solution. It
appears that solution acidified by H2SO4 is far more favorable than by
CO2-bubbled acidification. In addition, as dissolved oxygen was
stripped out of solution by N2 gas bubbling, the arsenate removal
dropped significantly. To take advantages of common practice of
carbonation and oxic condition, pretreatment of CO2 and air bubbling
in sequence are recommended for a better removal of arsenate.
Digital Article Identifier (DOI):
35
9470
A Novel Microarray Biclustering Algorithm
Abstract: Biclustering aims at identifying several biclusters that
reveal potential local patterns from a microarray matrix. A bicluster is
a sub-matrix of the microarray consisting of only a subset of genes
co-regulates in a subset of conditions. In this study, we extend the
motif of subspace clustering to present a K-biclusters clustering (KBC)
algorithm for the microarray biclustering issue. Besides minimizing
the dissimilarities between genes and bicluster centers within all
biclusters, the objective function of the KBC algorithm additionally
takes into account how to minimize the residues within all biclusters
based on the mean square residue model. In addition, the objective
function also maximizes the entropy of conditions to stimulate more
conditions to contribute the identification of biclusters. The KBC
algorithm adopts the K-means type clustering process to efficiently
make the partition of K biclusters be optimized. A set of experiments
on a practical microarray dataset are demonstrated to show the
performance of the proposed KBC algorithm.
Digital Article Identifier (DOI):
34
10671
Numerical Optimization Design of PEM Fuel Cell Performance Applying the Taguchi Method
Abstract: The purpose of this paper is applied Taguchi method on the optimization for PEMFC performance, and a representative Computational Fluid Dynamics (CFD) model is selectively performed for statistical analysis. The studied factors in this paper are pressure of fuel cell, operating temperature, the relative humidity of anode and cathode, porosity of gas diffusion electrode (GDE) and conductivity of GDE. The optimal combination for maximum power density is gained by using a three-level statistical method. The results confirmed that the robustness of the optimum design parameters influencing the performance of fuel cell are founded by pressure of fuel cell, 3atm; operating temperature, 353K; the relative humidity of anode, 50%; conductivity of GDE, 1000 S/m, but the relative humidity of cathode and porosity of GDE are pooled as error due to a small sum of squares. The present simulation results give designers the ideas ratify the effectiveness of the proposed robust design methodology for the performance of fuel cell.
Digital Article Identifier (DOI):
33
1243
Identification of an Mechanism Systems by Using the Modified PSO Method
Abstract: This paper mainly proposes an efficient modified
particle swarm optimization (MPSO) method, to identify a slidercrank
mechanism driven by a field-oriented PM synchronous motor.
In system identification, we adopt the MPSO method to find
parameters of the slider-crank mechanism. This new algorithm is
added with “distance" term in the traditional PSO-s fitness function to
avoid converging to a local optimum. It is found that the comparisons
of numerical simulations and experimental results prove that the
MPSO identification method for the slider-crank mechanism is
feasible.
Digital Article Identifier (DOI):
32
12313
Why Traditional Technology Acceptance Models Won't Work for Future Information Technologies?
Abstract: This paper illustrates why existing technology
acceptance models are only of limited use for predicting and
explaining the adoption of future information and communication
technologies. It starts with a general overview over technology
adoption processes, and presents several theories for the acceptance
as well as adoption of traditional information technologies. This is
followed by an overview over the recent developments in the area of
information and communication technologies. Based on the
arguments elaborated in these sections, it is shown why the factors
used to predict adoption in existing systems, will not be sufficient for
explaining the adoption of future information and communication
technologies.
Digital Article Identifier (DOI):
31
14316
Qualitative Survey on Managing Building Maintenance Projects
Abstract: Buildings are one of the valuable assets to provide
people with shelters for work, leisure and rest. After years of
attacks by weather, buildings will deteriorate which need proper
maintenance in order to fulfill the requirements and satisfaction of
the users. Poorly managed buildings not just give a negative image
to the city itself, but also pose potential risk hazards to the health
and safety of the general public. As a result, the management of
maintenance projects has played an important role in cities like
Hong Kong where the problem of urban decay has drawn much
attention. However, most research has focused on managing new
construction, and little research effort has been put on maintenance
projects. Given the short duration and more diversified nature of
work, repair and maintenance works are found to be more difficult
to monitor and regulate when compared with new works. Project
participants may face with problems in running maintenance
projects which should be investigated so that proper strategies can
be established. This paper aims to provide a thorough analysis on
the problems of running maintenance projects. A review of
literature on the characteristics of building maintenance projects
was firstly conducted, which forms a solid basis for the empirical
study. Results on the problems and difficulties of running
maintenance projects from the viewpoints of industry practitioners
will also be delivered with a view to formulating effective
strategies for managing maintenance projects successfully.
Digital Article Identifier (DOI):
30
10809
A Case Study of Applying Virtual Prototyping in Construction
Abstract: The use of 3D computer-aided design (CAD) models
to support construction project planning has been increasing in the
previous year. 3D CAD models reveal more planning ideas by
visually showing the construction site environment in different stages
of the construction process. Using 3D CAD models together with
scheduling software to prepare construction plan can identify errors
in process sequence and spatial arrangement, which is vital to the
success of a construction project. A number of 4D (3D plus time)
CAD tools has been developed and utilized in different construction
projects due to the awareness of their importance. Virtual prototyping
extends the idea of 4D CAD by integrating more features for
simulating real construction process. Virtual prototyping originates
from the manufacturing industry where production of products such
as cars and airplanes are virtually simulated in computer before they
are built in the factory. Virtual prototyping integrates 3D CAD,
simulation engine, analysis tools (like structural analysis and
collision detection), and knowledgebase to streamline the whole
product design and production process. In this paper, we present the
application of a virtual prototyping software which has been used in
a few construction projects in Hong Kong to support construction
project planning. Specifically, the paper presents an implementation
of virtual prototyping in a residential building project in Hong Kong.
The applicability, difficulties and benefits of construction virtual
prototyping are examined based on this project.
Digital Article Identifier (DOI):
29
530
Artificial Accelerated Ageing Test of 22 kVXLPE Cable for Distribution System Applications in Thailand
Abstract: This paper presents the experimental results on
artificial ageing test of 22 kV XLPE cable for distribution system
application in Thailand. XLPE insulating material of 22 kV cable
was sliced to 60-70 μm in thick and was subjected to ac high voltage
at 23
Ôùª
C, 60
Ôùª
C and 75
Ôùª
C. Testing voltage was constantly applied to
the specimen until breakdown. Breakdown voltage and time to
breakdown were used to evaluate life time of insulating material.
Furthermore, the physical model by J. P. Crine for predicts life time
of XLPE insulating material was adopted as life time model and was
calculated in order to compare the experimental results. Acceptable
life time results were obtained from Crine-s model comparing with
the experimental result. In addition, fourier transform infrared
spectroscopy (FTIR) for chemical analysis and scanning electron
microscope (SEM) for physical analysis were conducted on tested
specimens.
Digital Article Identifier (DOI):
28
14871
Pattern Recognition of Partial Discharge by Using Simplified Fuzzy ARTMAP
Abstract: This paper presents the effectiveness of artificial
intelligent technique to apply for pattern recognition and
classification of Partial Discharge (PD). Characteristics of PD signal
for pattern recognition and classification are computed from the
relation of the voltage phase angle, the discharge magnitude and the
repeated existing of partial discharges by using statistical and fractal
methods. The simplified fuzzy ARTMAP (SFAM) is used for pattern
recognition and classification as artificial intelligent technique. PDs
quantities, 13 parameters from statistical method and fractal method
results, are inputted to Simplified Fuzzy ARTMAP to train system
for pattern recognition and classification. The results confirm the
effectiveness of purpose technique.
Digital Article Identifier (DOI):
27
5464
Forecasting Foreign Direct Investment with Modified Diffusion Model
Abstract: Prior research has not effectively investigated how the
profitability of Chinese branches affect FDIs in China [1, 2], so this
study for the first time incorporates realistic earnings information
to systematically investigate effects of innovation, imitation, and
profit factors of FDI diffusions from Taiwan to China. Our nonlinear
least square (NLS) model, which incorporates earnings factors,
forms a nonlinear ordinary differential equation (ODE) in numerical
simulation programs. The model parameters are obtained through
a genetic algorithms (GA) technique and then optimized with the
collected data for the best accuracy. Particularly, Taiwanese regulatory
FDI restrictions are also considered in our modified model to meet
the realistic conditions. To validate the model-s effectiveness, this
investigation compares the prediction accuracy of modified model
with the conventional diffusion model, which does not take account
of the profitability factors.
The results clearly demonstrate the internal influence to be positive,
as early FDI adopters- consistent praises of FDI attract potential firms
to make the same move. The former erects a behavior model for the
latter to imitate their foreign investment decision. Particularly, the
results of modified diffusion models show that the earnings from
Chinese branches are positively related to the internal influence. In
general, the imitating tendency of potential consumers is substantially
hindered by the losses in the Chinese branches, and these firms would
invest less into China. The FDI inflow extension depends on earnings
of Chinese branches, and companies will adjust their FDI strategies
based on the returns. Since this research has proved that earning is
an influential factor on FDI dynamics, our revised model explicitly
performs superior in prediction ability than conventional diffusion
model.
Digital Article Identifier (DOI):
26
7722
Power System Load Shedding: Key Issues and New Perspectives
Abstract: Optimal load shedding (LS) design as an emergency plan is one of the main control challenges posed by emerging new uncertainties and numerous distributed generators including renewable energy sources in a modern power system. This paper presents an overview of the key issues and new challenges on optimal LS synthesis concerning the integration of wind turbine units into the power systems. Following a brief survey on the existing LS methods, the impact of power fluctuation produced by wind powers on system frequency and voltage performance is presented. The most LS schemas proposed so far used voltage or frequency parameter via under-frequency or under-voltage LS schemes. Here, the necessity of considering both voltage and frequency indices to achieve a more effective and comprehensive LS strategy is emphasized. Then it is clarified that this problem will be more dominated in the presence of wind turbines.
Digital Article Identifier (DOI):
25
8104
Estimation of Bayesian Sample Size for Binomial Proportions Using Areas P-tolerance with Lowest Posterior Loss
Abstract: This paper uses p-tolerance with the lowest posterior
loss, quadratic loss function, average length criteria, average
coverage criteria, and worst outcome criterion for computing of
sample size to estimate proportion in Binomial probability function
with Beta prior distribution. The proposed methodology is examined,
and its effectiveness is shown.
Digital Article Identifier (DOI):
24
12074
Frequency Regulation Support by Variable-Speed Wind Turbines and SMES
Abstract: This paper quantifies the impact of providing a shortterm
excess active power support of a variable speed wind turbine
(VSWT) and effect of super magnetic energy storage (SMES) unit on
frequency control, particularly temporary minimum frequency (TMF)
term. To demonstrate the effect of these factors on the power system
frequency, a three-area power system is considered as a test system.
Digital Article Identifier (DOI):
23
7064
Impact of Electronic Word-of-Mouth to Consumer Adoption Process in the Online Discussion Forum: A Simulation Study
Abstract: Web-based technologies have created numerous
opportunities for electronic word-of-mouth (eWOM) communication.
There are many factors that affect customer adoption and decisionmaking
process. However, only a few researches focus on some
factors such as the membership time of forum and propensity to trust.
Using a discrete-time event simulation to simulate a diffusion model
along with a consumer decision model, the study shows the effect of
each factor on adoption of opinions on on-line discussion forum. The
purpose of this study is to examine the effect of factor affecting
information adoption and decision making process. The model is
constructed to test quantitative aspects of each factor. The simulation
study shows the membership time and the propensity to trust has an
effect on information adoption and purchasing decision. The result of
simulation shows that the longer the membership time in the
communities and the higher propensity to trust could lead to the
higher demand rates because consumers find it easier and faster to
trust the person in the community and then adopt the eWOM. Other
implications for both researchers and practitioners are provided.
Digital Article Identifier (DOI):
22
6581
The Effect of Tmax in Energy Consumption in 0IEEE 802.16e with Traffic Load
Abstract: Energy consumption is an important design issue for
Mobile Subscriber Station (MSS) in the standard IEEE 802.16e.
Because mobility of MSS implies that energy saving becomes an
issue so that lifetime of MSS can be extended before re-charging.
Also, the mechanism in efficiently managing the limited energy is
becoming very significant since a MSS is generally energized by
battery. For these, sleep mode operation is recently specified in the
MAC (Medium Access Control) protocol. In order to reduce the
energy consumption, we focus on the sleep-mode and wake-mode of
the MAC layer, which are included in the IEEE 802.16 standards [1-
2].
Digital Article Identifier (DOI):
21
15296
A Novel Nano-Scaled SRAM Cell
Abstract: To help overcome limits to the density of conventional SRAMs and leakage current of SRAM cell in nanoscaled CMOS technology, we have developed a four-transistor SRAM cell. The newly developed CMOS four-transistor SRAM cell uses one word-line and one bit-line during read/write operation. This cell retains its data with leakage current and positive feedback without refresh cycle. The new cell size is 19% smaller than a conventional six-transistor cell using same design rules. Also the leakage current of new cell is 60% smaller than a conventional sixtransistor SRAM cell. Simulation result in 65nm CMOS technology shows new cell has correct operation during read/write operation and idle mode.
Digital Article Identifier (DOI):
20
13224
Structural Basis of Resistance of Helicobacterpylori DnaK to Antimicrobial Peptide Pyrrhocoricin
Abstract: Bacterial molecular chaperone DnaK plays an essential role in protein folding, stress response and transmembrane targeting of proteins. DnaKs from many bacterial species, including Escherichia coli, Salmonella typhimurium and Haemophilus infleunzae are the molecular targets for the insect-derived antimicrobial peptide pyrrhocoricin. Pyrrhocoricin-like peptides bind in the substrate recognition tunnel. Despite the high degree of crossspecies sequence conservation in the substrate-binding tunnel, some bacteria are not sensitive to pyrrhocoricin. This work addresses the molecular mechanism of resistance of Helicobacter pylori DnaK to pyrrhocoricin. Homology modelling, structural and sequence analysis identify a single aminoacid substitution at the interface between the lid and the β-sandwich subdomains of the DnaK substrate-binding domain as the major determinant for its resistance.
Digital Article Identifier (DOI):
19
6489
Inhibitory Effect of Lactic Acid and Nisin on Bacterial Spoilage of Chilled Shrimp
Abstract: Lactic acid alone and its combined application with
nisin were evaluated for reducing population of naturally occurring
microorganisms on chilled shrimp. Fresh shrimps were dipped in 0,
1.0% and 2.0% (v/v) lactic acid alone and their combined application
with 0.04 (g/L/kg) nisin solution for 10 min. Total plate counts of
aerobic bacteria (TPCs), Psychrotrophic counts, population of
Pseudomonas spp., H2S producing bacteria and Lactic acid bacteria
(LAB) on shrimps were determined during storage at 4 °C. The
results indicated that total plate counts were 2.91 and 2.63 log CFU/g
higher on untreated shrimps after 7 and 14 days of storage,
respectively, than on shrimps treated with 2.0% lactic acid combined
with 0.04 (g/L/kg) nisin. Both concentrations of lactic acid indicated
significant reduction on Pseudomonas counts during storage, while
2.0% lactic acid combined with nisin indicated the highest reduction.
In addition, H2S producing bacteria were more sensitive to high
concentration of lactic acid combined with nisin during storage.
Digital Article Identifier (DOI):
18
4383
Agent-Based Simulation and Analysis of Network-Centric Air Defense Missile Systems
Abstract: Network-Centric Air Defense Missile Systems
(NCADMS) represents the superior development of the air defense
missile systems and has been regarded as one of the major research
issues in military domain at present. Due to lack of knowledge and
experience on NCADMS, modeling and simulation becomes an effective
approach to perform operational analysis, compared with
those equation based ones. However, the complex dynamic interactions
among entities and flexible architectures of NCADMS put forward
new requirements and challenges to the simulation framework
and models. ABS (Agent-Based Simulations) explicitly addresses
modeling behaviors of heterogeneous individuals. Agents have capability
to sense and understand things, make decisions, and act on the
environment. They can also cooperate with others dynamically to
perform the tasks assigned to them. ABS proves an effective approach
to explore the new operational characteristics emerging in
NCADMS. In this paper, based on the analysis of network-centric
architecture and new cooperative engagement strategies for
NCADMS, an agent-based simulation framework by expanding the
simulation framework in the so-called System Effectiveness Analysis
Simulation (SEAS) was designed. The simulation framework specifies
components, relationships and interactions between them, the
structure and behavior rules of an agent in NCADMS. Based on scenario
simulations, information and decision superiority and operational
advantages in NCADMS were analyzed; meanwhile some
suggestions were provided for its future development.
Digital Article Identifier (DOI):
17
11447
On the Robust Stability of Homogeneous Perturbed Large-Scale Bilinear Systems with Time Delays and Constrained Inputs
Abstract: The stability test problem for homogeneous large-scale perturbed bilinear time-delay systems subjected to constrained inputs is considered in this paper. Both nonlinear uncertainties and interval systems are discussed. By utilizing the Lyapunove equation approach associated with linear algebraic techniques, several delay-independent criteria are presented to guarantee the robust stability of the overall systems. The main feature of the presented results is that although the Lyapunov stability theorem is used, they do not involve any Lyapunov equation which may be unsolvable. Furthermore, it is seen the proposed schemes can be applied to solve the stability analysis problem of large-scale time-delay systems.
Digital Article Identifier (DOI):
16
15232
The Potential of Strain M Protease in Degradations of Protein in Natural Rubber Latex
Abstract: Strain M was isolated from the latex of Hevea brasiliensis that grow in the rubber farm area of Malaysia Rubber Board. Strain M was tentatively identified as Bacillus sp. Strain M demonstrated high protease production at pH 9, and this was suitable to be applied in rubber processing that was in alkaline conditions. The right and suitable proportion to be used in applying supernatant into the latex was two parts of latex and one part of enzyme. In this proportion, the latex was stable throughout the 72 hours of treatment. The potential of strain M to degrade protein in the natural rubber latex was proven with the reduction of 79.3% nitrogen in 24 hours treatment. Centrifugation process of the latex before undergoing the treatment had increased the protein degradation in latex. Although the centrifugation process did not achieve zero nitrogen content, it had improved the performance of protein denaturing in the natural rubber.
Digital Article Identifier (DOI):
15
14309
Detection of Salmonella in Egg Shell and Egg Content from Different Housing Systems for Laying Hens
Abstract: Polymerase chain reaction (PCR) assay and
conventional microbiological methods were used to detect bacterial
contamination of egg shells and egg content in different commercial
housing systems, open house system and evaporative cooling system.
A PCR assay was developed for direct detection using a set of
primers specific for the invasion by A gene (invA) of Salmonella spp.
PCR detected the presence of Salmonella in 2 samples of shell egg
from the evaporative cooling system, while conventional cultural
methods detected no Salmonella from the same samples.
Digital Article Identifier (DOI):
14
5839
The Effect of Complementary Irrigation in Different Growth Stages on Yield, Qualitative and Quantitative Indices of the Two Wheat (Triticum aestivum L.) Cultivars in Mazandaran
Abstract: In most wheat growing moderate regions and
especially in the north of Iran climate, is affected grain filling by
several physical and abiotic stresses. In this region, grain filling often
occurs when temperatures are increasing and moisture supply is
decreasing. The experiment was designed in RCBD with split plot
arrangements with four replications. Four irrigation treatments
included (I0) no irrigation (check); (I1) one irrigation (50 mm) at
heading stage; (I2) two irrigation (100 mm) at heading and anthesis
stage; and (I3) three irrigation (150 mm) at heading, anthesis and
early grain filling growth stage, two wheat cultivars (Milan and
Shanghai) were cultured in the experiment. Totally raining was 453
mm during the growth season. The result indicated that biological
yield, grain yield and harvest index were significantly affected by
irrigation levels. I3 treatment produced more tillers number in m2,
fertile tillers number in m2, harvest index and biological yield. Milan
produced more tillers number in m2, fertile tillers in m2, while
Shanghai produced heavier tillers and grain 1000 weight. Plant height
was significant in wheat varieties while were not statistically
significant in irrigation levels. Milan produced more grain yield,
harvest index and biological yield. Grain yield shown that I1, I2, and
I3 produced increasing of 5228 (21%), 5460 (27%) and 5670 (29%)
kg ha-1, respectively. There was an interaction of irrigation and
cultivar on grain yields. In the absence of the irrigation reduced grain
1000 weight from 45 to 40 g. No irrigation reduced soil moisture
extraction during the grain filling stage. Current assimilation as a
source of carbon for grain filling depends on the light intercepting
viable green surfaces of the plant after anthesis that due to natural
senescence and the effect of various stresses. At the same time the
demand by the growing grain is increasing. It is concluded from
research work that wheat crop irrigated Milan cultivar could increase
the grain yield in comparison with Shanghai cultivar. Although, the
grain yield of Shanghai under irrigation was slightly lower than
Milan. This grain yield also was related to weather condition, sowing
date, plant density and location conditions and management of
fertilizers, because there was not significant difference in biological
and straw yield. The best result was produced by I1 treatment. I2 and
I3 treatments were not significantly difference with I1 treatment.
Grain yield of I1 indicated that wheat is under soil moisture
deficiency. Therefore, I1 irrigation was better than I0.
Digital Article Identifier (DOI):
13
12878
Automatic Image Alignment and Stitching of Medical Images with Seam Blending
Abstract: This paper proposes an algorithm which automatically aligns and stitches the component medical images (fluoroscopic) with varying degrees of overlap into a single composite image. The alignment method is based on similarity measure between the component images. As applied here the technique is intensity based rather than feature based. It works well in domains where feature based methods have difficulty, yet more robust than traditional correlation. Component images are stitched together using the new triangular averaging based blending algorithm. The quality of the resultant image is tested for photometric inconsistencies and geometric misalignments. This method cannot correct rotational, scale and perspective artifacts.
Digital Article Identifier (DOI):
12
7751
Heavy Metal Concentrations in Fanworth (Cabombafurcata) from Lake Chini, Malaysia
Abstract: Study was conducted to determine the concentration of
copper, cadmium, lead and zinc in Cabomba furcata that found
abundance in Lake Chini. This aquatic plant was collected randomly
within the lake for heavy metal determination. Water quality
measurement was undertaken in situ for temperature, pH,
conductivity and dissolved oksigen using portable multi sensor probe
YSI model 556. The C. furcata was digested using wet digestion
method and heavy metal concentrations were analysed using Atomic
Absorption Spectrometer (AAS) Perkin Elmer 4100B (flame
method). Result of water quality classify Lake Chini between class II
to class III using Malaysian Water Quality Standard. According to
this standard, Lake Chini has moderate quality, which normal for
natural lake. Heavy metal concentrations in C.furcata were low and
found to be lower than the critical toxic value in aquatic plants. Oneway
ANOVA test indicated the heavy metal concentrations in
C.furcata were significantly differ between sampling location. Water
quality and heavy metal concentrations indicates that Lake Chini was
not receives anthropogenic load from nearby activities.
Digital Article Identifier (DOI):
11
1357
MPPT Operation for PV Grid-connected System using RBFNN and Fuzzy Classification
Abstract: This paper presents a novel methodology for Maximum Power Point Tracking (MPPT) of a grid-connected 20 kW Photovoltaic (PV) system using neuro-fuzzy network. The proposed method predicts the reference PV voltage guarantying optimal power transfer between the PV generator and the main utility grid. The neuro-fuzzy network is composed of a fuzzy rule-based classifier and three Radial Basis Function Neural Networks (RBFNN). Inputs of the network (irradiance and temperature) are classified before they are fed into the appropriated RBFNN for either training or estimation process while the output is the reference voltage. The main advantage of the proposed methodology, comparing to a conventional single neural network-based approach, is the distinct generalization ability regarding to the nonlinear and dynamic behavior of a PV generator. In fact, the neuro-fuzzy network is a neural network based multi-model machine learning that defines a set of local models emulating the complex and non-linear behavior of a PV generator under a wide range of operating conditions. Simulation results under several rapid irradiance variations proved that the proposed MPPT method fulfilled the highest efficiency comparing to a conventional single neural network.
Digital Article Identifier (DOI):
10
8400
Flexible, Adaptable and Scaleable Business Rules Management System for Data Validation
Abstract: The policies governing the business of any
organization are well reflected in her business rules. The business
rules are implemented by data validation techniques, coded during
the software development process. Any change in business
policies results in change in the code written for data validation
used to enforce the business policies. Implementing the change in
business rules without changing the code is the objective of this
paper. The proposed approach enables users to create rule sets at
run time once the software has been developed. The newly defined
rule sets by end users are associated with the data variables for
which the validation is required. The proposed approach facilitates
the users to define business rules using all the comparison
operators and Boolean operators. Multithreading is used to
validate the data entered by end user against the business rules
applied. The evaluation of the data is performed by a newly
created thread using an enhanced form of the RPN (Reverse Polish
Notation) algorithm.
Digital Article Identifier (DOI):
9
1003
Improvement of Durability of Wood by Maleic Anhydride
Abstract: Wood as a natural renewable material is vulnerable to
degradation by microorganisms and susceptible to change in
dimension by water. In order to effectively improve the durability of
wood, an active reagent, maleic anhydride (Man) was selected for
wood modification. Man was first dissolved into a solvent, and then
penetrated into wood porous structure under a vacuum/pressure
condition. After a final catalyst-thermal treatment, wood modification
was finished. The test results indicate that acetone is a good solvent for
transporting Man into wood matrix. SEM observation proved that
wood samples treated by Man kept a good cellular structure, indicating
a well penetration of Man into wood cell walls. FTIR analysis
suggested that Man reacted with hydroxyl groups on wood cell walls
by its ring-ether group, resulting in reduction of amount of hydroxyl
groups and resultant good dimensional stability as well as fine decay
resistance. Consequently, Man modifying wood to improve its
durability is an effective method.
Digital Article Identifier (DOI):
8
8559
Comparative Studies of Support Vector Regression between Reproducing Kernel and Gaussian Kernel
Abstract: Support vector regression (SVR) has been regarded
as a state-of-the-art method for approximation and regression. The
importance of kernel function, which is so-called admissible support
vector kernel (SV kernel) in SVR, has motivated many studies
on its composition. The Gaussian kernel (RBF) is regarded as a
“best" choice of SV kernel used by non-expert in SVR, whereas
there is no evidence, except for its superior performance on some
practical applications, to prove the statement. Its well-known that
reproducing kernel (R.K) is also a SV kernel which possesses many
important properties, e.g. positive definiteness, reproducing property
and composing complex R.K by simpler ones. However, there are a
limited number of R.Ks with explicit forms and consequently few
quantitative comparison studies in practice. In this paper, two R.Ks,
i.e. SV kernels, composed by the sum and product of a translation
invariant kernel in a Sobolev space are proposed. An exploratory
study on the performance of SVR based general R.K is presented
through a systematic comparison to that of RBF using multiple
criteria and synthetic problems. The results show that the R.K is
an equivalent or even better SV kernel than RBF for the problems
with more input variables (more than 5, especially more than 10) and
higher nonlinearity.
Digital Article Identifier (DOI):
7
474
Motivated Support Vector Regression using Structural Prior Knowledge
Abstract: It-s known that incorporating prior knowledge into support
vector regression (SVR) can help to improve the approximation
performance. Most of researches are concerned with the incorporation
of knowledge in the form of numerical relationships. Little work,
however, has been done to incorporate the prior knowledge on the
structural relationships among the variables (referred as to Structural
Prior Knowledge, SPK). This paper explores the incorporation of SPK
in SVR by constructing appropriate admissible support vector kernel
(SV kernel) based on the properties of reproducing kernel (R.K).
Three-levels specifications of SPK are studied with the corresponding
sub-levels of prior knowledge that can be considered for the method.
These include Hierarchical SPK (HSPK), Interactional SPK (ISPK)
consisting of independence, global and local interaction, Functional
SPK (FSPK) composed of exterior-FSPK and interior-FSPK. A
convenient tool for describing the SPK, namely Description Matrix
of SPK is introduced. Subsequently, a new SVR, namely Motivated
Support Vector Regression (MSVR) whose structure is motivated
in part by SPK, is proposed. Synthetic examples show that it is
possible to incorporate a wide variety of SPK and helpful to improve
the approximation performance in complex cases. The benefits of
MSVR are finally shown on a real-life military application, Air-toground
battle simulation, which shows great potential for MSVR to
the complex military applications.
Digital Article Identifier (DOI):
6
12342
A Bayesian Network Reliability Modeling for FlexRay Systems
Abstract: The increasing importance of FlexRay systems in
automotive domain inspires unceasingly relative researches. One
primary issue among researches is to verify the reliability of FlexRay
systems either from protocol aspect or from system design aspect.
However, research rarely discusses the effect of network topology on
the system reliability. In this paper, we will illustrate how to model
the reliability of FlexRay systems with various network topologies by
a well-known probabilistic reasoning technology, Bayesian Network.
In this illustration, we especially investigate the effectiveness of error
containment built in star topology and fault-tolerant midpoint
synchronization algorithm adopted in FlexRay communication
protocol. Through a FlexRay steer-by-wire case study, the influence
of different topologies on the failure probability of the FlexRay steerby-
wire system is demonstrated. The notable value of this research is
to show that the Bayesian Network inference is a powerful and
feasible method for the reliability assessment of FlexRay systems.
Digital Article Identifier (DOI):
5
8186
Family-size Biogas Plant Using Manure and Urine Mixture at Ambient Temperature in Semi-arid Regions of Northwestern China
Abstract: Biogas, a clean renewable energy, is attracting a growing
concern of researchers and professionals in many fields. Based
on the natural and climatic conditions in semi-arid regions of northwestern
China, the present study introduces a specifically-designed
family-size biogas plant (with a digester of 10m3) with manure
and urine of animals and humanity as raw materials. The biogas
plant is applicable to areas with altitudes of more than 2000 meters
in northwestern China. In addition to the installation cost, a little
operational expenditure, structure, characteristics, benefits of this
small-scale biogas plant, this article introduces a wide range of
specific popularization methods such as training, financial support,
guided tour to the biogas plant, community-based group study and
delivery of operational manuals. The feasibility of the biogas plant is
explored on the basis of the availability of the raw materials. Simple
operations contained in the current work increase the possibility of
the wide use of this small-scale biogas plant in similar regions of the
world.
Digital Article Identifier (DOI):
4
6729
Performance Comparison of Single and Multi-Path Routing Protocol in MANET with Selfish Behaviors
Abstract: Mobile Ad Hoc network is an infrastructure less
network which operates with the coordination of each node. Each node
believes to help another node, by forwarding its data to/from another
node. Unlike a wired network, nodes in an ad hoc network are resource
(i.e. battery, bandwidth computational capability and so on)
constrained. Such dependability of one node to another and limited
resources of nodes can result in non cooperation by any node to
accumulate its resources. Such non cooperation is known as selfish
behavior.
This paper discusses the performance analysis of very well known
MANET single-path (i.e. AODV) and multi-path (i.e. AOMDV)
routing protocol, in the presence of selfish behaviors. Along with
existing selfish behaviors, a new variation is also studied. Extensive
simulations were carried out using ns-2 and the study concluded that
the multi-path protocol (i.e. AOMDV) with link disjoint configuration
outperforms the other two configurations.
Digital Article Identifier (DOI):
3
10661
Pig Husbandry and Solid Manures in a Commercial Pig Farm in Beijing, China
Abstract: Porcine production in China represents approximately
the 50% of the worldwide pig production. Information about pig
husbandry characteristics in China and manure properties from sows
to fatteners in intensive pig farms are not broadly available for
scientific studies as it is a time consuming, expensive task and highly
inaccessible. This study provides a report about solid pig manures
(28% dry matter) in a commercial pig farm located in the peri-urban
area of Beijing as well as a general overview of the current pig
husbandry techniques including pig breeds, feeds, diseases, housing as
well as pig manure and wastewater disposal. The main results are
intended to serve as a literature source for young scientists in order to
understand the main composition of pig manures as well as to identify
the husbandry techniques applied in an intensive pig farm in Beijing.
Digital Article Identifier (DOI):
2
4487
Strategy Analysis and Creation by Simulation in the General Game
Abstract: In this paper the General Game problem is described.
In this problem the competition or cooperation dilemma occurs as the
two basic types of strategies. The strategy possibilities have been
analyzed for finding winning strategy in uncertain situations (no
information about the number of players and their strategy types).
The winning strategy is missing, but a good solution can be found by
simulation by varying the ratio of the two types of strategies. This
new method has been used in a real contest with human players,
where the created strategies by simulation have reached very good
ranks. This construction can be applied in other real social games as
well.
Digital Article Identifier (DOI):
1
2882
Finding Equilibrium in Transport Networks by Simulation and Investigation of Behaviors
Abstract: The goal of this paper is to find Wardrop equilibrium
in transport networks at case of uncertainty situations, where the
uncertainty comes from lack of information. We use simulation tool
to find the equilibrium, which gives only approximate solution, but
this is sufficient for large networks as well. In order to take the
uncertainty into account we have developed an interval-based
procedure for finding the paths with minimal cost using the
Dempster-Shafer theory. Furthermore we have investigated the users-
behaviors using game theory approach, because their path choices
influence the costs of the other users- paths.
Digital Article Identifier (DOI):